Professional Documents
Culture Documents
Tartalomjegyzék
Ez a sokoldalú, kis fokozatú tápegység teljesen beállítható 0–36 V és 0–3 amper között.
Az Amazonon és az eBay-en elérhető, ez egy remek kiegészítő a padon. Legalább enyém van.
A felhasználói kézikönyv következő szakaszai segítenek abban, hogy a B3603 működjön a következő projektben.
A feszültség határértéke
A jelenlegi határérték
Kimeneti feszültség - valós időben
Jelenlegi kimenet - valós időben
Amp órák - a bekapcsolás óta felhalmozódtak.
Teljesítmény - wattban, valós időben
Navigáció a különféle beállítási menükhöz és memóriamenükhöz.
Elektromos előírások
Bemeneti feszültség 6 - 40 Vdc
Kimeneti feszültség 0-36 Vdc
Kimeneti áram 0 - 2A hűtés nélkül. 0 - 3A hűtéssel
Feszültség kijelző felbontása 0,01 Vdc
Jelenlegi képernyőfelbontás 0.001A
Teljesítmény kijelző felbontása 0,001 Watt
Amp Hour Display Resolution 0,001 AH
Hatékonyság Akár 92 százalék
Kimeneti hullámosság <= 50 mV
Működési hőmérséklet tartomány -40 ° C és +85 ° C között
Kapcsolási frekvencia 150 kHz
Rövidzárlat-védelem Állandó áramkorlát által beállítva
Fordított polaritás elleni védelem Egyik sem. Telepítsen egy diódát, ha szükséges.
Fizikai méretek
Hossz 66mm
Magasság 21mm
Szélesség 50mm
Interfész és csatlakozások
Ha az 'Out' LED nem világít, akkor a feszültség beállítási pontja jelenik meg.
Ha az 'Out' LED nem világít, akkor az aktuális beállított pont jelenik meg.
A két kijelző tehát azt jelenti, hogy az utolsó bekapcsolás óta két amperórát vontak ki a tápegységből.
CV LED - Ha világít, az áramellátás állandó feszültség üzemmódban van. Ez azt jelenti, hogy a kimeneti feszültség a beállított értéken van, és az áram
változik.
CC LED - Ha világít, a B3603 állandó áram üzemmódban van. Ez azt jelenti, hogy az áramkorlátot elérték és a feszültség változik.
OUT LED - világít, ha az áramellátás be van kapcsolva és táplálja. Ha nincs, a kimenet ki van kapcsolva.
SET GOMB - Ha az OUT LED világít, akkor a set gomb megnyomásával kikapcsolhatja a B3603 készüléket.
Ha az OUT LED nem világít, a beállító gomb megnyomásakor a kijelző a feszültség és az áram beállított pontjai között ciklusba lép.
OK GOMB - Ha az OUT LED nem világít, akkor az OK gomb megnyomásával bekapcsolhatja az áramellátást.
Ha az OUT LED világít, és a kijelző rögzített értéket mutat, akkor a gyors megnyomásával a következő érték léphet át.
Ha az OUT LED világít, az OK gomb egy másodpercnél hosszabb megnyomása esetén a kijelző olyan üzemmódba lép, amelyben automatikusan átkapcsol a
különféle tápegység értékek között, vagy a kijelző olyan módba lép, amelyben rögzített érték jelenik meg.
FEL NYÍL - Ennek a gombnak a megnyomásával megnő a beállított érték, amit valaha jelenít meg az érték.
Egy gyors megnyomásával az érték egy számjegytel növekszik. A gomb lenyomásával az érték gyorsan növekszik.
Egy gyors megnyomásával az érték egy számjegytel csökken. A gomb lenyomásával az érték gyorsan csökken.
Funkció 0 - Lehetővé teszi a kiválasztáshoz, hogy a kimenet engedélyezve van-e vagy sem, amikor a lefelé konverter áramellátása táplálkozik.
1. funkció - A felhasználó választhatja, hogy megjeleníti-e az energiafogyasztást és az amperórákat.
2. funkció - A felhasználó dönthet úgy, hogy bekapcsolásként átvált-e az értékek között.
Például a 0-as funkció lehetővé teszi a felhasználó számára, hogy kiválasztja, hogy a kimenet automatikusan bekapcsol-e vagy sem, amikor
tápfeszültséget bekapcsolják. Ha az áramellátást úgy konfigurálták, hogy az azonnal táplálja a kimenetet, amikor a tápellátást először
alkalmazzák, akkor az 'OK gomb' elengedése esetén a B3603 visszakapcsol arra az állapotra, ahol a kimenet ki van kapcsolva, amikor az áramot
először alkalmazzák.
Automatikus kimeneti opció
A B3603 Step Down Converter lehetővé teszi a felhasználó számára, hogy az első tápellátás bekapcsolásakor válassza ki az energiaellátást.
Ha olyan üzemmódba helyezi, ahol a B3603 automatikusan kimeneti energiát szolgáltat bekapcsoláskor, a tápegység ezt az energiát biztosítja az utolsó feszültség és áram
beállítások alapján.
Ha a B3603 olyan üzemmódban van, ahol a kimeneti áram kikapcsol, akkor a kimenetet az 'OK gomb' megnyomásával kell engedélyezni, míg a B3603 áramellátása után.
Bármelyik állapotban a 'SET gomb' megnyomása kikapcsolja a kimenetet.
Az amperóra kijelzése tekintetében fontos megjegyezni, hogy a kimenet kikapcsolása a „SET gomb” segítségével nem állítja vissza a számlálót
nullára. Ehelyett a kimenet kikapcsolása egyszerűen megállítja a számlálást. Ha a kimenetet újra bekapcsolja az „OK gomb” segítségével, az
amperórák számlálása folytatódni fog.
Más szavakkal, az Amp Hour kijelzőt csak akkor kell visszaállítani, ha a B3603-ra visszakapcsolják a tápfeszültséget.
This versatile little step down power supply is fully adjustable from 0 to 36V and 0 to 3 Amps.
Offered on Amazon and eBay, it is a cool addition to your bench. At least it is on mine.
This following sections of this user manual will help you to put the B3603 to work in your next project.
Electrical Specifications
Input Voltage 6 to 40 Vdc
Output Voltage 0 to 36 Vdc
Output Current 0 to 2A with no cooling. 0 to 3A with cooling
Voltage Display Resolution 0.01 Vdc
Current Display Resolution 0.001A
Power Display Resolution 0.001 Watt
Amp Hour Display Resolution 0.001 AH
Efficiency Up to 92 percent
Output Ripple <= 50mV
Operating Temperature Range -40 deg C to +85 deg C
Switching Frequency 150 kHz
Short Circuit Protection Set by constant current limit
Reverse Polarity Protection None. Install a diode if necessary.
Physical Dimensions
Length 66mm
Height 21mm
Width 50mm
Controls, Inputs and Outputs
The illustration below shows the various displays, controls and connections available on the B3603 and is followed by a basic functional
description of each.
Input – DC voltage source connects here. Accepts between 6 and 40 volts dc. The input voltage must be higher than the desired output voltage. Also ensure that you use
the correct polarity as there is not protection.
Output – DC Load or device that you want to power connects here. The output is adjustable from 0 to 36 Vdc. The output voltage must be lower than the input voltage.
Note On Input and Output – These are non-isolated. That is to say that the negative terminals for both the input and output are the same electrical point.
Display – When the output is off, it will show the set points for both voltage and current. When the output is on, it shows that actual voltage and current outputs.
The position of the decimal point is what determines whether the indication is for voltage or current. In more advance modes, the display will also show the power and amp
hours.
See the illustrations and explanations below.
Voltage is being displayed when the second decimal from the left is lit.
If the ‘Out’ LED is lit, then the actual voltage output is being displayed
If the ‘Out’ LED is off, the voltage set point is being displayed.
Current is being displayed when the first decimal from the left is lit.
If the ‘Out’ LED is lit, then the actual current output is being displayed
If the ‘Out’ LED is off, the current set point is being displayed.
If the first letter of the display in ‘P’, then actual power output is being shown.
The value being displayed is in watts. Thus, “P2.00” is equal to 2.00 watts and P.200 is equal to .200 watts.
Watts of course meaning voltage times current.
If C is the first letter of the display, then amp hours are being shown.
These are cumulative since power was applied.
Thus a display of two means that two amp hours are have been drawn from the supply since it was last turned on.
CV LED – When lit, the power supply is in the Constant Voltage mode. This means the output voltage is at the value set and it is current that is varying.
CC LED – When lit, the B3603 is in the Constant Current mode. This means the current limit has been reached and voltage is varying.
OUT LED – When lit, the power supply is on and is supplying power. When off, its output is off.
SET BUTTON – If the OUT LED is on, pressing the set button will turn the B3603 off.
If OUT LED is off, pressing the set button will cause the display to cycle between the voltage and current set points.
OK BUTTON – If the OUT LED is off, pressing the OK button will turn the power supply on.
If the OUT LED is on and display is showing a fixed value, a quick press will cycle to the next value.
If the OUT LED is on, pressing the OK button for more than a second will cause the display to enter a mode where it automatically cycles between the various power supply
values or will cause the display to enter a mode where is displays a fixed value.
UP ARROW- Pressing this button will increase the set point of what ever value is being display.
A quick single press, will increase the value by one digit. Holding the button down will cause the value to increase rapidly.
The set points can be changed with the power output on or off.
DOWN ARROW- Pressing this button will decrease the set point of the value being display.
A quick single press, will decrease the value by one digit. Holding the button down will cause the value to decrease rapidly.
Function 0 – Allows use to choose whether or not the output is enable when power is supplied to the step down converter.
Function 1 – User may select whether or not to display power and amp hours.
Function 2 – User can choose to whether or not to cycle between values as a power up option.
Accessing the Functions Menu
The Power Supply’s Functions Menu is accessed by applying power with the ‘OK Button’ pressed. With the ‘OK Button’ still pressed after
power is applied the display will cycle between three values that represent the three user configurable options.
The steps to accessing the functions menu are as follows:
For example, Function 0 allows the user to choose whether or not the output is automatically on when power is applied. If the power supply
were configured to immediately provide an output when power is first applied, releasing the ‘OK Button’ would cause the B3603 to toggle to
the state where output is off when power is first applied.
Automatic Power Output Option
The B3603 Step Down Converter allows the user select whether or not the power supply provides an output when first powered up.
If placed in a mode where the B3603 automatically applies power output when powered up, the supply will provide that power based on the last voltage
and current settings.
If the B3603 is placed in a mode where the power output is first off, it will be necessary to enable the output by pressing the ‘OK Button’ while after
power is applied the the B3603.
In either state, pressing the ‘SET Button’ will turn the power output off.
Determine the Power Output Configuration
It is recommended that the user first determine the Power Output state before changing the configuration. The process is simple.
Step 1 – Remove or turn off power to the power supply.
Step 2 – Apply or turn on power to the power supply.
Step 3– Note whether or not the ‘OUT LED’ is illuminated.
If the ‘OUT LED’ is illuminated, the power supply is set up to automatically provide an output when first turned on.
If the ‘OUT LED’ is not illuminated, the power supply is set so that output is off when the B3603 is first energized.