Professional Documents
Culture Documents
www.tyco-fire.com
Contacts
DIFFUSER
SHAPE
WRENCH RECESS
(USE ONLY
END "A")
1.22"
(31,0 mm)
FIGURE 2
W-TYPE 6 WRENCH
7 Components:
8
1 - Strainer Frequent visual inspections are recom
1-11/16" 6 2 - Orifice Insert mended to be initially performed for
(42,9 mm) 9
3 - Frame nozzles installed in potentially corro
WRENCH 5 4 - Button sive atmospheres to verify the integ
2-3/8" FLATS 5 - Sealing rity of the materials of construction
(60,3 mm) 4 Assembly and finish as they may be affected by
6 - Bulb the corrosive conditions present for a
11/16"
3 7 - Loading given installation. Thereafter, annual
(17,5 mm)
Screw inspections per applicable standards
2 8 - Diffuser are required, in addition to inspec
11/16" 9 - Ejection
(17,5 mm)
1/2" NPT tions required by the authority having
7/16" (11,1 mm) Spring
NOMINAL 1 jurisdiction.
MAKE-IN The owner is responsible for the
inspection, testing, and maintenance of
FIGURE 1
their fire protection system and devices
TYPE ULF AM30 AQUAMIST NOZZLE
in compliance with this document, as
NOMINAL DIMENSIONS
well as with the applicable standards
of any other authorities having juris
Installation Care and diction. Contact the installing contrac
tor or product manufacturer with any
TYCO Ultra Low Flow AQUAMIST
Nozzles Type ULF AM30 must be
Maintenance questions.
Water mist systems should be in
installed in accordance with this TYCO Ultra Low Flow AQUAMIST spected, tested, and maintained by a
section. Nozzles Type ULF AM30 must be main qualified Inspection Service in accor
Do not install any bulb type nozzle if tained and serviced in accordance with dance with local requirements and/or
the bulb is cracked or there is a loss this section. national codes.
of liquid from the bulb. With the nozzle Before closing a fire protection system
held horizontally, a small air bubble
should be present. The diameter of
main control valve for maintenance
work on the fire protection system
Limited
the air bubble is approximately 1,6 mm
(1/16 in.) for the 57°C (135°F) to 2,4 mm
that it controls, obtain permission to
shut down the affected fire protection
Warranty
(3/32 in.) for the 182°C (360°F) temper system from the proper authorities For warranty terms and conditions, visit
ature ratings. and notify all personnel who may be www.tyco-fire.com.
A leak-tight 1/2 inch NPT nozzle joint affected by this action.
should be obtained by applying a min
imum-to-maximum torque of 9,5 to
Nozzles which are found to be leaking
or exhibiting visible signs of corrosion
Ordering
19,0 Nm (7 to 14 lb-ft). Higher levels
of torque can distort the nozzle inlet
must be replaced. Procedure
Automatic nozzles must never be Contact your local distributor for avail
and cause leakage or impairment of
painted, plated, coated, or other ability. When placing an order, indicate
the nozzle.
wise altered after leaving the factory. the full product name and part number
Type ULF AM30 Modified nozzles must be replaced. (P/N).
The Type ULF AM30 AQUAMIST Nozzles that have been exposed to
Nozzles must be installed in accor corrosive products of combustion, but Type ULF AM30 AQUAMIST Nozzles
dance with the following instructions: have not operated, should be replaced Specify: Type ULF AM30 AQUA
if they cannot be completely cleaned MIST Nozzle with Natural Brass finish,
Step 1. Install the Type ULF AM30 in the (specify) temperature rating, P/N
by wiping the nozzle with a cloth or by
upright position as shown in Figure 1. (specify):
brushing it with a soft bristle brush.
Step 2. With pipe thread sealant 57°C (135°F) . . . . . . . . . . . . . . . . . 49-230-1-135
Care must be exercised to avoid
app lied to the pipe threads, hand- 68°C (155°F) . . . . . . . . . . . . . . . . . 49-230-1-155
damage to the nozzles before, during,
tighten the nozzle into the nozzle fitting. 79°C (175°F) . . . . . . . . . . . . . . . . . . 49-230-1-175
and after installation. Nozzles damaged 93°C (200°F) . . . . . . . . . . . . . . . . . 49-230-1-200
Step 3. Tighten the nozzle into the by dropping, striking, wrench twist/ 141°C (286°F) . . . . . . . . . . . . . . . . 49-230-1-286
nozzle fitting using only the W-Type 6 slippage, or the like, must be replaced. 182°C (360°F) . . . . . . . . . . . . . . . . 49-230-1-360
Wrench (Ref. to Figure 2). With refer Also, replace any nozzle that has a Wrench
ence to Figure 1, apply the W-Type 6 cracked bulb or that has lost liquid from Specify: W-Type 6 Sprinkler Wrench,
Wrench to the wrench flats. its bulb (Ref. Installation section). P/N 56-000-6-387
NATIONAL FIRE PROTECTION ASSOCIATION and NFPA are registered trademarks of National Fire Protection Association;
TEFLON is a registered trademark of DuPont