Professional Documents
Culture Documents
Lighting (interior)
Lighting system
Function inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-3
Parts location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-4
Symptom table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-7
How to troubleshoot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-8
Check list for interview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-10
Customize function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-10
Circuit figure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-12
ECM terminal arrangement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-15
Data monitor / active test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-17
ACC signal circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-18
IG signal circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-23
Door courtesy light circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-25
Engine switch illumination circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-29
cardiagn.com
Door unlock detection switch circuit. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front door courtesy light switch circuit. . . . . . . . . . . . . . . . . . . . . . . . . . .
LI-30
LI-33
LI
Trunk courtesy light switch circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-37
Interior illumination circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-40
Ignition key cylinder light circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-42
Vanity light
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-46
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-46
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-47
Unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-47
Personal map light
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-48
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-48
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-49
Unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-50
Trunk room light
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-51
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-52
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-53
Unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-53
Door courtesy light (installed to the front side)
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-54
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-54
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-56
Unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-56
Ignition key cylinder light
Exploded view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-57
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-57
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-57
Unit inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LI-58
LI–2
cardiagn.com
LI
Lighting (interior) - Lighting system
LI–3
Lighting system
Interior body
Lighting (interior)
& electrical
Function inspection
1. Before troubleshooting
(1) Basic inspection
(a)Measure the battery voltage.
Voltage: 11 to 14V (when the engine is stopped)
(2) Inspect for blown light bulbs and fuses, wiring harnesses open circuit, short circuits, and poor contact of connectors, in
places where you can inspect visually.
2. Illuminated entry system control operation check A
CAUTION:
Perform the check with the initial settings of the customize function.
NOTE:
The following lights will illuminate with the illuminated entry system (Perform the check with the mode change switch of the
map light ASSY set to the DOOR mode):
• Map light ASSY
• Push button start switch (text illumination) *1
• Transponder key amplifier (key cylinder light) *2
*1: When there is a smart entry & start system
*2: When there is no smart entry & start system
cardiagn.com
(1) Check that the lights illuminate in the following conditions:
(a)Open one of the doors.
LI
(2) Check that the light illuminates for 15 seconds and then goes off in one of the following conditions:
(a)Enter the ID collation area for the smart key. * 1
(b)Perform the unlock operation (wireless unlock, smart unlock, and unlock with key interlock).
(c)When any doors are open with IG OFF, close all the doors.
(d)With all the doors closed, turn the ignition from IG ON →IG OFF.
*1: When there is a smart entry & start system
(3) Check that the lights go off in one of the following conditions:
(a)Exit the ID collation area for the smart key, then wait for 3 seconds or more. * 1
(b)Close and lock all the doors with IG OFF.
(c)With all the doors closed, turn the ignition to ACC ON or IG ON.
(d)When the lights illuminate with IG OFF, turn the ignition to ACC ON or start the engine.
*1: When there is a smart entry & start system
3. Battery saver inspection
(1) When one of the doors is not fully closed with IG OFF, check that the lights that illuminated with the illuminated entry sys-
tem go off after approx. 20 minutes.
NOTE:
If the operating conditions for the light control are met, the battery saver control will be cancelled.
LI–4 Lighting (interior) - Lighting system
Parts location
cardiagn.com
LI
- DCC fuse
- DOME fuse
- MPX-B fuse
- ECM-B fuse
cardiagn.com
LI
LI-01694
LI–6 Lighting (interior) - Lighting system
Main body ECM (multiplex network Instrument panel junction block ASSY
body computer)
- ACC 1 relay
- GAUGE fuse
cardiagn.com
LI
SL-02002
Lighting (interior) - Lighting system
LI–7
Symptom table
Illuminated entry system
Symptoms Inspection items Reference pages
The lights do not properly illuminate in all the operating condi- Interior illumination circuit LI - 40
tions. Main body ECM (multiplex network body computer) PD - 25
The light control does not work with the door open/close oper- Front door courtesy light switch circuit LI - 33
ations. Main body ECM (multiplex network body computer) PD - 25
The light control does not work with the door lock operation. Main body ECM (multiplex network body computer) PD - 25
CAN communication system check NW - 30
The light control does not operate when entering the smart
Operation check of the smart entry & start system (smart entry function) TD - 27
detection area.
Main body ECM (multiplex network body computer) PD - 25
IG signal circuit LI - 23
The light control does not work when operating the push but-
ACC signal circuit LI - 18
ton start switch *1 or the ignition switch ASSY *2.
Main body ECM (multiplex network body computer) PD - 25
CAN communication system check NW - 30
The push button start switch (text illumination) does not illumi-
Engine switch illumination circuit LI - 29
nate. *1
Smart key computer ASSY (collation ECM) -
cardiagn.com
Map light ASSY
Symptoms Inspection items Reference pages LI
Bulb -
The map light ASSY does not illuminate. Map light ASSY LI - 50
Vehicle wiring harness and connector -
Battery saver
Symptoms Inspection items Reference pages
IG signal circuit LI - 23
ACC signal circuit LI - 18
The battery saver does not work. Front door courtesy light switch circuit LI - 33
CAN communication system check NW - 30
Main body ECM (multiplex network body computer) -
The transponder key amplifier (key cylinder light) does not illu- Ignition key cylinder light circuit LI - 42
minate. *1 Vehicle wiring harness and connector -
Main body ECM (multiplex network body computer) PD - 25
How to troubleshoot
Next
NOTE:
cardiagn.com
Refer to LI - 10.
LI Next
4 Symptom table
NOTE:
Refer to LI - 7.
Result
Result Go to
Not applicable to the symptom
A
table.
Applicable to the symptom table. B
B Go to Step 6.
5 Based on the trouble phenomenon, perform troubleshooting following the steps below.
Next
Next
7 Confirmation test
Next
Complete
cardiagn.com
LI
LI–10 Lighting (interior) - Lighting system
Year/date of
Lighting (Interior) Diagnosis Checklist for Interview vehicle bring-in Year Month Date
Name Registration First
Year Month Date
No. registration
Vehicle
Frame No.
model
Odometer
Interviewer Inspector Engine type reading
Customer specified content
Date when trouble occurred (from when) Year Month Date Time
cardiagn.com
LI Weather
Road
Fine / Cloudy / Rainy / Snowy / Other (
)
Temperature Approx. ( ) °C (°F)
Illumination
Switch
Trouble symptom
LI-01607
customize function
1. Customization of the lighting system (interior)
(1) Customization using the SSM4
Lighting (interior) - Lighting system
LI–11
(a)Connect the SSM4 to the DLC3 and turn the ignition to IG ON.
(b)According to the screen of SSM4, select [Each System] →[Body Control] →[Customize] for customizing.
Display name Initial setting Contents Setting Controller ECM
Set the function to automatically turn off the interior light
[Lighting Time] 15 seconds after all the doors are shut, when the interior light is set to 15/7.5/30 seconds
the DOOR mode.
Set the function to automatically turn on the interior light by
[I/L when ACC OFF] [ON] turning the ignition from ACC ON →OFF, when the interior [ON]/[OFF]
light is set to the DOOR mode. Main body ECM
Set the function to automatically turn on the interior light in (multiplex network
[I/L ON W/Door Key accordance with the door unlock operation with the smart body computer)
[ON] [ON]/[OFF]
Unlock] key or the mechanical key, when the interior light is set to
the DOOR mode.
[Room Light when Set the function to turn on the interior light when the driver
[ON] [ON]/[OFF]
Approached] approaches the vehicle carrying the smart key.
[Interior Light Control] [ON] Set the function to turn on the interior light by a timer. [ON]/[OFF]
cardiagn.com
LI
LI–12 Lighting (interior) - Lighting system
Circuit figure
22
D5 ACC
28
3B *1
1 9
Battery 3E MB ACC
ECM ACC
20
Smart key computer ASSY*1 3A
Ignition switch ASSY*2 ACC1
8
MB IG
ECM IG1
15
Smart key computer ASSY*1 3A
12 IG1 NO.1
Ignition switch ASSY*2
3A
cardiagn.com
LI 13
3A
18 11
3B MB GND
28 16
1
3A MB FDCY
H21
Front door courtesy light switch ASSY LH
13 10
1
3B MB FPCY
G18
Front door courtesy light switch ASSY RH
5
2 1
D5 FLCL
E2
Courtesy light ASSY LH
HAZ 2
Battery MB KSWB
19 32
3C MB +B
MPX-B
27 1
Battery 3A MB BECU
DCC ECM-B
A
DOME 26 12
2 E D+ 3
3D MB
J3
Trunk lock
Instrument panel
junction block ASSY
1 2
cardiagn.com
H8
LI
Trunk room light
28
2 6
ILL+ ILL- D5 ILL
D54
Transponder key amplifier *1
7
DOOR DOOR SW 3
2 +B D5 DOMR
OFF GND 1
ON
1
K3
Map light ASSY D6 GND
1 2 4
A73 GND
K1
Vanity light RH
1 2
K5
Vanity light LH Main body ECM
(multiplex network body computer)
8 E LSSR 7 12
LSFD
F3
Front door lock ASSY RH
7 E LSSR 8 11
LSFP
E3
Front door lock ASSY LH
D6
Main body ECM (multiplex
cardiagn.com
LI network body computer)
2
Battery D48 +B
AM2 NO.2
5
IG2 relay D41 IG2
GAUGE
16
SWIL 9
D41 SWIL
24
AGND 6
D41 AGND
D25 11
Push start switch D48 GND
SL-02004
Lighting (interior) - Lighting system
LI–15
/$
$
&
% #
'
cardiagn.com
/$ LI
& % '
$ #
Captions in illustration
*1 Instrument panel junction block ASSY *2 Main body ECM (multiplex network body computer)
(1) Inspection of the main body ECM (multiplex network body computer) and the instrument panel junction block ASSY
LI–16 Lighting (interior) - Lighting system
(a)Disconnect the connector of the main body ECM (multiplex network body computer).
(b)Measure the voltage between the connector terminals on the vehicle wiring harness side.
Standard value
Terminal No. (Terminal symbol) Inspection conditions Standard value
D5-22 (ACC) ←→chassis ground *1 ACC ON 11 to 14V
cardiagn.com
3E-1 ←→chassis ground Always 11 to 14V
NOTE:
If it is out of the standard value, it can be judged as malfunction of the vehicle.
(e)Connect the connectors of the main body ECM (multiplex network body computer) and the instrument panel junction
block ASSY.
(f) Measure the voltage or waveform between the connector terminals.
Standard value
Terminal No. (Terminal symbol) Inspection conditions Standard value
3B-13 ←→chassis ground With driver's door closed →opened 11 to 14V →Less than 1V
3A-28 ←→chassis ground With passenger's door closed →opened 11 to 14V →Less than 1V
3D-26 ←→chassis ground With trunk closed →opened 11 to 14V →Less than 1V
D5-5 (FLCL) ←→chassis ground Driver's side courtesy light ON →OFF Less than 1 V →11 to 14 V
D5-6 (FRCL) ←→chassis ground Passenger's side courtesy light ON →OFF Less than 1 V →11 to 14 V
D5-7 (DOMR) ←→chassis ground Map light ASSY OFF →ON Less than 1V
Transponder key amplifier (key cylinder light) ON
D5-28 (ILL) ←→chassis ground *2 11 to 14V →Less than 1V
→OFF
D6-11 (LSFD) ←→chassis ground *1 Driver's side door locked →unlocked Pulse generation →less than 1 V
D6-12 (LSFP) ←→chassis ground *1 Passenger's side door locked →unlocked Pulse generation →less than 1 V
cardiagn.com
(b)Measure the voltage and resistance between the connector terminals of the smart key computer ASSY (collation
ECM) on the vehicle side. LI
Standard value
Terminal No. (Terminal sym-
Input/Output Item Inspection conditions Standard value
bol)
D48-2 (+B)←→D48-11 Input Voltage Always 11 to 14V
D48-11 (GND) ←→chassis
- Resistance Always Less than 1 Ω
ground
NOTE:
If it is out of the standard value, it can be judged as malfunction of the vehicle.
(c)Connect the connector D48 of the smart key computer ASSY (collation ECM).
(d)Measure the voltage between the connector terminals.
Standard value
Terminal No. (Terminal sym-
Input/Output Item Inspection conditions Standard value
bol)
D41-16 (SWIL)←→D41-24 Push button start switch ON
Output Voltage 11 to 14V →Less than 1V
(AGND) →OFF
D41-5 (IG2) ←→Chassis
Input Voltage IG ON 11 to 14V
ground
NOTE:
If the measured value is not within the range of the standard value, it can be determined that the smart key computer
ASSY (collation ECM) has a fault.
cardiagn.com
ON
NOTE:
*: Perform the inspection with the changing switch of the map light ASSY set to the DOOR mode.
SSM4 screen: [Each System] →[Keyless Access(Collation ECM)] →[Active Test]
Item name Item description Drive
Turn on the text illumination of the push button start
[Key illumi. Lamp] Stop/output
switch.
Circuit figure
22
D5 ACC
28
3B *2
1 9
Battery 3E MB ACC
ECM ACC
20
Ignition switch ASSY*1 3A
12 ACC1
Smart key computer ASSY
(Collation ECM)*2 3A
13
3A
cardiagn.com
*2: with smart entry and start system
Main body ECM
(multiplex network body computer) LI
LI-10986
Inspection steps
CAUTION:
Before performing the troubleshooting, check the fuse of this circuit.
(1) On the SSM4, navigate to the [Data monitor] display, and check the
computer data. (Refer to LI - 17)
Criteria: The normal value on the data monitor is displayed prop-
erly.
SSM4 screen: [Each System] →[Body Control] →[Data monitor]
Item name Description/display range Normal value Remarks
OFF: ACC OFF
Status of the ACC signal This item will be displayed as
[ACC SW] ON: The power mode is ACC
Display range: OFF-ON [ON] in the IG ON status.
ON or IG ON.
NG Go to Step 2.
OK
See the next circuit for inspection shown on the symptom table. (Refer to LI - 7)
2 Inspection of the wiring harness and the connector (ACC1 relay power supply)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connectors 3A and 3E of the instrument panel junction
block ASSY.
LI–20 Lighting (interior) - Lighting system
(2) Measure the voltage between the connector terminals on the vehicle
C wiring harness side.
' Voltage
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
Result
Result Go to
cardiagn.com
OK (smart entry & start system not equipped) A
LI OK (smart entry & start system equipped) B
NG C
Captions in illustration
Front side of vehicle wiring harness connector
*a
(instrument panel junction block ASSY connector)
B Go to Step 4.
3 Inspection of the instrument panel junction block ASSY (ACC1 relay inspection)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Remove the instrument panel junction block ASSY from the vehicle.
(Refer to PD - 25)
(2) Remove the main body ECM (multiplex network body computer) from
the instrument panel junction block ASSY.
(3) Measure the resistance between the terminals.
Lighting (interior) - Lighting system
LI–21
C ' #
/$
#%%
Captions in illustration
Connector not connected
*a - -
(Instrument panel junction block ASSY)
cardiagn.com
Resistance LI
Inspection terminals Inspection conditions Standard value
3E-1 - MB-9 (ACC) Always 10 kΩ or more
Connect the battery's
positive terminal to the
3A-20 terminal, and
3E-1 - MB-9 (ACC) Less than 1 Ω
the ground terminal to
the 3A-12 or the 3A-13
terminal.
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
4 Inspection of the instrument panel junction block ASSY (ACC1 relay inspection)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Remove the instrument panel junction block ASSY from the vehicle.
(Refer to PD - 25)
(2) Remove the main body ECM (multiplex network body computer) from
the instrument panel junction block ASSY.
(3) Measure the resistance between the terminals.
LI–22 Lighting (interior) - Lighting system
C ' # $
/$
Captions in illustration
Connector not connected
*a - -
(Instrument panel junction block ASSY)
cardiagn.com
LI Resistance
OK
5 Inspection of the wiring harness and the connector (instrument panel junction block ASSY - main
body ECM (multiplex network body computer))
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
IG signal circuit
Circuit description
The main body ECM (multiplex network body computer) is detecting the IG signal.
Circuit figure
cardiagn.com
LI
1 8
Battery 3E MB IG
ECU IG1
15
Ignition switch ASSY*1 3A
*1: Without smart entry & start system Main body ECM (multiplex network
body computer)
*2: With smart entry & start system
Inspection steps
CAUTION:
Before performing the troubleshooting, check the fuse of this circuit.
(1) On the SSM4, navigate to the [Data monitor] display, and check the
computer data. (Refer to LI - 17)
SSM4 screen: [Each System] →[Body Control] →[Data monitor]
Item name Description/display range Normal value Remarks
Status of the IG signal OFF: IG OFF This item will be displayed as
[Ignition]
Display range: OFF-ON ON: IG ON [OFF] in the ACC ON status.
LI–24 Lighting (interior) - Lighting system
NG Go to Step 2.
OK
See the next circuit for inspection shown on the symptom table. (Refer to LI - 7)
2 Inspection of the wiring harness and the connector (IG1 NO.1 relay power supply)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connectors 3A and 3E of the instrument panel junction
block ASSY.
(2) Measure the voltage between the connector terminals on the vehicle
C wiring harness side.
Voltage
cardiagn.com
'
LI Inspection terminals Inspection conditions Standard value
3E-1 - chassis ground Always 11 to 14V
3A-15 - chassis
IG ON 11 to 14V
ground
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
Captions in illustration
Front side of vehicle wiring harness connector
*a
(instrument panel junction block ASSY connector)
OK
3 Inspection of the instrument panel junction block ASSY (IG1 NO.1 relay inspection)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Remove the instrument panel junction block ASSY from the vehicle.
(Refer to PD - 25)
(2) Remove the main body ECM (multiplex network body computer) from
the instrument panel junction block ASSY.
(3) Measure the resistance between the terminals.
Lighting (interior) - Lighting system
LI–25
C ' #
/$
+)
Captions in illustration
Connector not connected
*a - -
(Instrument panel junction block ASSY)
cardiagn.com
Resistance LI
Inspection terminals Inspection conditions Standard value
3E-1 - MB-8 (IG) Always 10 kΩ or more
Connect the battery's
positive terminal to the
3A-15 terminal, and
3E-1 - MB-8 (IG) Less than 1 Ω
the ground terminal to
the 3A-12 or the 3A-13
terminal.
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
Circuit figure
2 1 6
Battery FRCL
DCC DOME
F4
Courtesy light ASSY RH
2 1 5
FLCL
E2
Courtesy light ASSY LH
D5
Main body ECM (multiplex network
cardiagn.com
body computer)
LI
LI-01705
Inspection steps
NOTE:
Before performing the troubleshooting, check the fuses and the lights of this circuit.
(1) Using SSM4, display the [Active Test] screen according to the screen
and check the computer data. (Refer to LI - 17)
SSM4 screen: [Each System] →[Body Control] →[Active Test]
Item name Item description Drive
The driver's side courtesy light is turned
[D-Door Courtesy Lamp] OFF/ON
on
The passenger's side courtesy light is
[P-Door Courtesy Lamp] OFF/ON
turned on
Criteria: The driver's and passenger's side courtesy lights are turned
on
Result
Result Go to
All items show the normal status. A
[D-Door Courtesy Lamp] shows an abnormal status. B
[P-Door Courtesy Lamp] shows an abnormal status. C
B Go to Step 2.
C Go to Step 5.
See the next circuit for inspection shown on the symptom table. (Refer to LI - 7)
Lighting (interior) - Lighting system
LI–27
2 Inspection of the wiring harness and the connector (courtesy light ASSY LH - battery)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector E2 of the courtesy light ASSY LH.
(2) Measure the voltage of the vehicle wiring harness connector.
Voltage
OK
cardiagn.com
(1) Remove the courtesy light ASSY LH. (Refer to LI - 54)
(2) Perform the unit inspection of the courtesy light ASSY LH. (Refer to LI - LI
56)
Criteria: The courtesy light ASSY LH illuminates.
OK
4 Inspection of the wiring harness and the connector (main body ECM (multiplex network body com-
puter) - courtesy light ASSY LH)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector D5 of the main body ECM (multiplex network
body computer).
(2) Disconnect the connector E2 of the courtesy light ASSY LH.
(3) Measure the resistance of the vehicle wiring harness connector.
Resistance
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
LI–28 Lighting (interior) - Lighting system
5 Inspection of the wiring harness and the connector (courtesy light ASSY RH - battery)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector F4 of the courtesy light ASSY RH.
(2) Measure the voltage of the vehicle wiring harness connector.
Voltage
OK
cardiagn.com
(1) Remove the courtesy light ASSY RH. (Refer to LI - 54)
LI (2) Perform the unit inspection of the courtesy light ASSY RH. (Refer to LI
- 56)
Criteria: The courtesy light ASSY RH illuminates.
OK
7 Inspection of the wiring harness and the connector (main body ECM (multiplex network body com-
puter) - courtesy light ASSY RH)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector D5 of the main body ECM (multiplex network
body computer).
(2) Disconnect the connector F4 of the courtesy light ASSY RH.
(3) Measure the resistance of the vehicle wiring harness connector.
Resistance
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
Lighting (interior) - Lighting system
LI–29
Circuit figure
16
SWIL 9
D41 SWIL
24
AGND 6
D41 AGND
cardiagn.com
LI
Inspection steps
(1) Using SSM4, display the [Active Test] screen according to the screen
and check the computer data. (Refer to LI - 17)
SSM4 screen: [Each System] →[Keyless Access(Collation ECM)] →[Active Test]
Item name Item description Drive
Turn on the text illumination of the push
[Key illumi. Lamp] Stop/output
button start switch.
NG Go to Step 2.
OK
See the next circuit for inspection shown on the symptom table. (Refer to LI - 7)
OK
3 Inspection of the wiring harness and the connector (push button start switch - smart key computer
ASSY (collation ECM) and chassis ground)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector D25 of the push button start switch.
(2) Disconnect the connector D41 of the smart key computer ASSY (colla-
tion ECM).
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
cardiagn.com
LI D41-16 (SWIL) - chas-
sis ground
Always 10 kΩ or more
D41-24 (AGND) -
Always 10 kΩ or more
chassis ground
OK
Circuit figure
12
8 E LSSR 7
D6 LSFP
F3
Front door lock ASSY RH
11
7 E LSSR 8
D6 LSFD
E3
Front door lock ASSY LH
ECU-B 1
Battery MB BECU
cardiagn.com
Main body ECM
(multiplex network body computer) LI
LI-10983
Inspection steps
CAUTION:
Before performing the troubleshooting, check the fuse of this circuit.
(1) On the SSM4, navigate to the [Data monitor] display, and check the
computer data. (Refer to LI - 17)
Criteria: The normal value on the data monitor is displayed prop-
erly.
SSM4 screen: [Each System] →[Body Control] →[Data monitor]
Item name Description/display range Normal value Remarks
[Lock]: When the driver's side
Lock/unlock status of the
door is locked.
[D Door Lock Pos] driver's side door -
[Unlock]: When the driver's
Display range: [Lock]-[Unlock]
side door is unlocked.
[Lock]: When the passen-
Lock/unlock status of the pas-
ger's side door is locked
[P Door Lock Pos] senger's side door -
[Unlock]: When the passen-
Display range: [Lock]-[Unlock]
ger's side door is unlocked
Result
Result Go to
OK A
NG (The door lock position switch of the driver's side door
B
does not operate.)
NG (The door lock position switch of the passenger's side
C
door does not operate.)
B Go to Step 2.
LI–32 Lighting (interior) - Lighting system
C Go to Step 4.
See the next circuit for inspection shown on the symptom table. (Refer to LI - 7)
(1) Remove the front door lock ASSY RH. (Refer to DL - 101)
(2) Perform the unit inspection of the front door lock ASSY RH. (Refer to
DL - 102)
Criteria: The inspection result shows the normal status.
OK
cardiagn.com
LI 3 Inspection of the wiring harness and the connector (front door lock ASSY RH - main body ECM (mul-
tiplex network body computer) and chassis ground)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector F3 of the front door lock ASSY RH.
(2) Disconnect the connector D6 of the main body ECM (multiplex network
body computer).
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
(1) Remove the front door lock ASSY LH. (Refer to DL - 101)
(2) Perform the unit inspection of the front door lock ASSY LH. (Refer to
DL - 102)
Criteria: The inspection result shows the normal status.
Lighting (interior) - Lighting system
LI–33
OK
5 Inspection of the wiring harness and the connector (front door lock ASSY LH - main body ECM (mul-
tiplex network body computer) and chassis ground)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector E3 of the front door lock ASSY LH.
(2) Disconnect the connector D6 of the main body ECM (multiplex network
body computer).
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
cardiagn.com
(LSSR)
E3-7 (E) - chassis
Always Less than 1 Ω
LI
ground
E3-8 (LSSR) - chas-
Always 10 kΩ or more
sis ground
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
Circuit figure
28 16
1
3A MB FDCY
G18
Front door courtesy light
switch ASSY RH
13 10
1
3B MB FPCY
MPX-B 32
Battery MB BMPX
cardiagn.com
LI
ECU-B 1
MB BECU
Inspection steps
CAUTION:
Before performing the troubleshooting, check the fuse of this circuit.
(1) On the SSM4, navigate to the [Data monitor] display, and check the
computer data. (Refer to LI - 17)
Criteria: The normal value on the data monitor is displayed prop-
erly.
SSM4 screen: [Each System] →[Body Control] →[Data monitor]
Item name Description/display range Normal value Remarks
[Close]: Close the driver's
Status of the front door cour-
door.
[D Door Courtesy] tesy light switch ASSY LH -
[Open]: Open the driver's
Display range: [Close]-[Open]
door.
Closed: Close the passen-
Status of the front door cour-
ger's door.
[P Door Courtesy] tesy light switch ASSY RH -
Open: Open the passenger's
Display range: [Close]-[Open]
door.
Result
Result Go to
OK A
Lighting (interior) - Lighting system
LI–35
Result Go to
NG (The courtesy light switch of the driver's side door
B
does not operate.)
NG (The courtesy light switch of the passenger's side
C
door does not operate.)
B Go to Step 5.
C Go to Step 2.
See the next circuit for inspection shown on the symptom table. (Refer to LI - 7)
(1) Remove the front door courtesy light switch ASSY RH. (Refer to LI -
cardiagn.com
59)
(2) Perform the unit inspection of the front door courtesy light switch ASSY LI
RH. (Refer to LI - 60)
Criteria: The inspection result shows the normal status.
OK
3 Inspection of the wiring harness and the connector (front door courtesy light switch ASSY RH -
instrument panel junction block ASSY)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector G18 of the front door courtesy light switch
ASSY RH.
(2) Disconnect the connector 3B of the instrument panel junction block
ASSY.
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
OK
NOTE:
For inspection procedures and precautions, refer to IN - 36.
LI–36 Lighting (interior) - Lighting system
(1) Remove the instrument panel junction block ASSY from the vehicle.
(Refer to PD - 25)
(2) Measure the resistance between the terminals.
(3) Remove the main body ECM (multiplex network body computer) from
the instrument panel junction block ASSY.
C
$
/$
(2%;
cardiagn.com
Resistance
LI Inspection terminals Inspection conditions Standard value
3B-13 - MB-10 (FPCY) Always Less than 1 Ω
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
(1) Remove the front door courtesy light switch ASSY LH. (Refer to LI - 59)
(2) Perform the unit inspection of the front door courtesy light switch ASSY
LH. (Refer to LI - 60)
Criteria: The inspection result shows the normal status.
OK
6 Inspection of the wiring harness and the connector (front door courtesy light switch ASSY LH - instru-
ment panel junction block ASSY)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector H21 of the front door courtesy light switch
ASSY LH.
(2) Disconnect the connector 3A of the instrument panel junction block
ASSY.
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Lighting (interior) - Lighting system
LI–37
Resistance
OK
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Remove the instrument panel junction block ASSY from the vehicle.
(Refer to PD - 25)
(2) Remove the main body ECM (multiplex network body computer) from
the instrument panel junction block ASSY.
(3) Measure the resistance between the terminals.
cardiagn.com
LI
C
#
/$
(&%;
Resistance
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
Circuit figure
26 12
2 E D+ 3
3D MB
J3
Trunk lock ASSY
Instrument panel
junction block ASSY
MPX-B 32
Battery MB BMPX
cardiagn.com
LI
Main body ECM
(multiplex network body computer)
LI-10970
Inspection steps
CAUTION:
Before performing the troubleshooting, check the fuse of this circuit.
(1) On the SSM4, navigate to the [Data monitor] display, and check the
computer data. (Refer to LI - 17)
SSM4 screen: [Each System] →[Body Control] →[Data monitor]
Item name Description/display range Normal value Remarks
Status of the trunk lock ASSY Closed: The trunk door is closed.
[Luggage Courtesy SW] -
Display range: [Close]-[Open] Open: The trunk door is open.
NG Go to Step 2.
OK
See the next circuit for inspection shown on the symptom table. (Refer to LI - 7)
3 2 1
3 (D+) - 2 (E) Locked 10 kΩ or more
Captions in illustration
&
' $ Connector not connected
*a
(trunk lock ASSY)
*b Locked
*c Open
OK
3 Inspection of the wiring harness and the connector (trunk lock ASSY - instrument panel junction
block ASSY and chassis ground)
cardiagn.com
NOTE:
For inspection procedures and precautions, refer to IN - 36.
LI
(1) Disconnect the connector 3D of the instrument panel junction block
ASSY.
(2) Disconnect the connector J3 of the trunk lock ASSY.
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
OK
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Remove the instrument panel junction block ASSY from the vehicle.
(Refer to PD - 25)
(2) Remove the main body ECM (multiplex network body computer) from
the instrument panel junction block ASSY.
(3) Measure the resistance between the terminals.
LI–40 Lighting (interior) - Lighting system
C
&
/$
Captions in illustration
Connector not connected
*a - -
(Instrument panel junction block ASSY)
Resistance
Inspection terminals
Inspection conditions Standard value
(Terminal symbol)
3D-26 - MB-12 Always Less than 1 Ω
cardiagn.com
LI NG Replacement of the instrument panel junction block ASSY
(Refer to PD - 25)
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
Circuit figure
DOOR
DOOR SW 3 7
DOMR
2 +B OFF
Battery
DCC DOME GND 1
ON
K3
Map light ASSY
D5
Main body ECM (multiplex network
body computer)
cardiagn.com
LI
Inspection steps
CAUTION:
Before performing the troubleshooting, check the bulbs and the fuses of this circuit.
(1) Using SSM4, perform an [Active Test] by following the display. (Refer
to LI - 17)
SSM4 screen: [Each System] →[Body Control] →[Active Test]
Item name Item description Drive
The lights controlled by the illuminated
[Illuminated Entry System] OFF/ON
entry system are turned on
NG Go to Step 2.
OK
OK
3 Inspection of the wiring harness and the connector (map light ASSY - battery)
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector K3 of the map light ASSY.
(2) Measure the voltage between the connector terminals on the vehicle
C wiring harness side.
Voltage
Captions in illustration
$ Front side of vehicle wiring harness connector
*a
(map light ASSY connector)
cardiagn.com
LI NG Repair or replacement of wiring harness or connector
OK
4 Inspection of the wiring harness and the connector (map light ASSY - main body ECM (multiplex net-
work body computer))
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector K3 of the map light ASSY.
(2) Disconnect the connector D5 of the main body ECM (multiplex network
body computer).
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
Circuit figure
28
2 6
Battery ILL+ ILL- D5 ILL
DCC DOME
D54
Transponder key
amplifier
cardiagn.com
LI
Inspection steps
CAUTION:
Before performing the troubleshooting, check the fuses and the lights of this circuit.
(1) Using SSM4, display the [Active Test] screen according to the screen
and check the computer data. (Refer to LI - 17)
SSM4 screen: [Each System] →[Body Control] →[Active Test]
Item name Item description Drive
[Key illumi. Lamp] Turn on the key cylinder light ON/OFF
NG Go to Step 2.
OK
See the next circuit for inspection shown on the symptom table. (Refer to LI - 7)
OK
3 Inspection of the wiring harness and the connector (transponder key amplifier - battery)
cardiagn.com
NOTE:
LI For inspection procedures and precautions, refer to IN - 36.
Inspection condi-
& 1 2 3 4 5 6 7 Inspection terminals Standard value
tions
D54-2 (ILL+) - chassis ground Always 11 to 14 V
OK
4 Inspection of the wiring harness and the connector (transponder key amplifier - main body ECM
(multiplex network body computer))
NOTE:
For inspection procedures and precautions, refer to IN - 36.
(1) Disconnect the connector D54 of the transponder key amplifier.
(2) Disconnect the connector D5 of the main body ECM (multiplex network
body computer).
(3) Measure the resistance between the connector terminals on the vehi-
cle wiring harness side.
Resistance
OK
Replacement of the main body ECM (multiplex network body computer) (Refer to PD - 25)
cardiagn.com
LI
LI–46 Lighting (interior) - Vanity light
Vanity light
Interior body
Lighting (interior)
& electrical
Exploded view
Visor ASSY RH
x2
cardiagn.com
LI Removal
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Removal of visor ASSY RH
(1) Remove the 2 screws.
(2) Disconnect the visor ASSY RH from the hook.
(3) Disconnect the connector and remove the visor ASSY RH.
Lighting (interior) - Vanity light
LI–47
Installation
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Installation of the vanity light bulb
(1) Install the vanity light bulb to the visor ASSY RH.
cardiagn.com
2. Installation of the vanity light lens
(1) Engage the claws and install the vanity light lens. LI
Unit inspection
1. Inspection of the visor ASSY RH
C (1) Measure the resistance between the connector terminals when the
visor ASSY RH (vanity light switch) is operated.
Resistance
Inspection terminals Inspection conditions Standard value
1-2 Mirror cover closed 10 kΩ or more
1-2 Mirror cover opened Less than 1 Ω
Captions in illustration
Connector not connected
*a
(visor ASSY RH)
LI–48 Lighting (interior) - Personal map light
Exploded view
cardiagn.com
LI
Removal
1. Removal of the map light ASSY
(1) Release the 2 tabs.
Lighting (interior) - Personal map light
LI–49
(2) Release two guides and disconnect the map light ASSY.
(3) Disconnect the connector and remove the map light ASSY.
cardiagn.com
LI
Installation
1. Installation of the map light bulb
(1) Install the map light bulb.
2. Installation of the map light lens NO.1
(1) Engage two claws and install the map light lens NO.1.
3. Installation of the map light ASSY
(1) Connect the connector.
(2) Insert two guides.
(3) Engage two claws and install the map light ASSY.
LI–50 Lighting (interior) - Personal map light
Unit inspection
1. Inspection of the map light ASSY
C (1) Illumination condition check for the map light
(a)Check the illumination condition of the map light when battery
voltage is applied between the connector terminals.
Criteria
Battery connection Inspection conditions Criteria
Battery positive terminal
→2(+B)
Map light switch ON The map light illuminates.
Battery ground terminal
&11459
$ )0& →1(GND)
Battery positive terminal
→2(+B)
Map light switch DOOR The map light illuminates.
Battery ground terminal
→3(DOOR SW)
Captions in illustration
Connector not connected
*a
(map light ASSY)
cardiagn.com
LI
Lighting (interior) - Trunk room light
LI–51
Exploded view
cardiagn.com
LI
LI-01589
LI–52 Lighting (interior) - Trunk room light
Removal
1. Removal of the trunk light ASSY NO.1
(1) Rotate the trunk light ASSY NO.1 as shown in the figure, and dis-
connect the trunk light ASSY NO.1 from the vehicle.
cardiagn.com
LI
(2) Disconnect the connector and remove the trunk light ASSY NO.1.
Installation
1. Installation of the trunk light bulb
(1) Install the trunk light bulb.
2. Installation of the trunk light lens
(1) Engage two claws and install the trunk light lens.
3. Installation of the trunk light ASSY NO.1
(1) Connect the connector.
cardiagn.com
(2) Rotate the trunk light ASSY NO.1 as shown in the figure, and
install the trunk light ASSY NO.1. LI
Unit inspection
1. Inspection of the trunk light ASSY NO.1
(1) Check the illumination condition when battery voltage is applied
C
between the connector terminals.
Criteria
Inspection terminals Inspection conditions Criteria
Battery positive →1
1-2 Light turns on.
Battery ground →2
Captions in illustration
Connector not connected
*a
(trunk light ASSY NO.1)
NOTE:
Perform the inspection using a properly functioning bulb.
LI–54 Lighting (interior) - Door courtesy light (installed to the front side)
Exploded view
cardiagn.com
LI
Courtesy light cover
Removal
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
Lighting (interior) - Door courtesy light (installed to the front side)
LI–55
cardiagn.com
LI
(2) Disconnect the connector and remove the courtesy light ASSY.
Installation
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Installation of the courtesy light bulb
(1) Install the courtesy light bulb.
(2) Engage the claws and install the courtesy light cover.
2. Installation of the courtesy light ASSY
(1) Connect the connector.
(2) Engage the claws and install the courtesy light ASSY.
# Captions in illustration
*A Installation location on the passenger's side
*B Installation location on the driver's side
cardiagn.com
LI $
Unit inspection
NOTE:
The procedures described below are for the RH side. Perform the same procedures for the LH side.
1. Inspection of the courtesy light ASSY
(1) Light inspection
C
(a)Inspect if the light turns on when battery voltage is applied to
each connector terminal.
Criteria
Inspection terminals Battery connection Criteria
Battery positive →1
1-2 Light turns on.
Battery ground →2
Captions in illustration
Connector not connected
*a
(courtesy light ASSY)
Lighting (interior) - Ignition key cylinder light
LI–57
Exploded view
cardiagn.com
LI
Transponder key amplifier
x2
SL-10294
Removal
1. Removal of the steering column cover LWR (Refer to WW - 22)
2. Removal of the steering column cover UPR (Refer to WW - 23)
3. Removal of the transponder key amplifier
(1) Disconnect the connector.
(2) Release the two claws by using a fine flat tip screwdriver wrapped
with protective tape, and remove the transponder key amplifier.
Captions in illustration
*1 Protective tape
Installation
1. Installation of the transponder key amplifier
(1) Engage two claws and install the transponder key amplifier.
LI–58 Lighting (interior) - Ignition key cylinder light
Unit inspection
1. Inspection of the transponder key amplifier
C (1) Light inspection
(a)Inspect if the light turns on when battery voltage is applied to
each connector terminal.
Criteria
Battery connection Criteria
Battery positive terminal →2 (ILL+)
Light turns on.
Battery ground terminal →6 (ILL-)
+.. +..
Captions in illustration
Connector not connected
*a
(transponder key amplifier)
cardiagn.com
LI
Lighting (interior) - Front door courtesy switch
LI–59
Exploded view
cardiagn.com
LI
7.5 {77,5.5}
LI-01546
Removal
NOTE:
The following procedure is for LH side. Perform the same procedures for the RH side.
1. Removal of the front door courtesy light switch ASSY
(1) Remove the bolt.
LI–60 Lighting (interior) - Front door courtesy switch
(2) Disconnect the connector and remove the front door courtesy light
switch ASSY.
Installation
NOTE:
The following procedure is for LH side. Perform the same procedures for the RH side.
1. Installation of the front door courtesy light switch ASSY
(1) Connect the connector.
(2) Install the front door courtesy light switch ASSY with the bolt.
Standard value:T=7.5N·m {77kgf·cm} {5.5ft·lbf}
cardiagn.com
LI Unit inspection
NOTE:
The following procedure is for LH side. Perform the same procedures for the RH side.
1. Inspection of the front door courtesy light switch ASSY
C (1) Measure the resistance when the shaft of the front door courtesy
light switch ASSY is operated.
Resistance
Inspection terminals Inspection conditions Standard value
When the shaft is not pushed
1 - Chassis ground Less than 1 Ω
in
1 - Chassis ground When the shaft is pushed in 10 kΩ or more
Captions in illustration
Connector not connected
*a
(front door courtesy light switch ASSY)