Professional Documents
Culture Documents
1
Company: Page: 1
Specifier: Project: Riyadh Metro
Address: Sub-Project I Pos. No.: Case-2
Phone I Fax: | Date: 11/1/2015
E-Mail:
Specifier's comments: Edge distance considered as infinity, Concrete strength considered as 40 MPA, Bar size increased from M16 to M20.
Since there is moment; which is creating tension force, Our PROFIS Rebar software not considering this tension force which is being
developed by moment. So that, we have done study on PROFIS Anchor.
1 Input data
Anchor type and diameter: HIT-HY 200 + Rebar 20mm
Dynamic set or any suitable annular gap filling solution
Effective embedment depth: hef,opti = 365 mm (hef,limit = 400 mm)
Material: B500B
Evaluation Service Report: ETA 11/0493
Issued I Valid: 4/15/2015 | 4/15/2020
Proof: Design method Engineering judgement SOFA BOND - based on ETAG BOND testing
Stand-off installation: eb = 0 mm (no stand-off); t = 1 mm
Anchor plate: lx x ly x t = 220 mm x 1250 mm x 1 mm; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, , fc = 40.00 N/mm2; h = 450 mm, Temp. short/long: 40/24 °C
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any Ø) or >= 100 mm (Ø <= 10 mm)
no longitudinal edge reinforcement
Reinforcement to control splitting according to EOTA TR 029, 5.2.2.6 present.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.6.1
Company: Page: 2
Specifier: Project: Riyadh Metro
Address: Sub-Project I Pos. No.: Case-2
Phone I Fax: | Date: 11/1/2015
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.6.1
Company: Page: 3
Specifier: Project: Riyadh Metro
Address: Sub-Project I Pos. No.: Case-2
Phone I Fax: | Date: 11/1/2015
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.6.1
Company: Page: 4
Specifier: Project: Riyadh Metro
Address: Sub-Project I Pos. No.: Case-2
Phone I Fax: | Date: 11/1/2015
E-Mail:
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.6.1
Company: Page: 5
Specifier: Project: Riyadh Metro
Address: Sub-Project I Pos. No.: Case-2
Phone I Fax: | Date: 11/1/2015
E-Mail:
7 Warnings
• Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the loading!
Input data and results must be checked for agreement with the
existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EOTA TR 029, Section 7!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 4.1 of EOTA TR029! For larger
diameters of the clearance hole see Chapter 1.1. of EOTA TR029!
• The design method ETAG (filled holes) assumes that no hole clearance between the anchors and the fixture is present. This can
be
achieved by filling the gap with mortar of sufficient compressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• Bore hole cleaning must be performed according to instructions for use (blow twice with oil-free compressed air (min. 6 bar), brush twice,
blow twice with oil-free compressed air (min. 6 bar)).
• Characteristic bond resistances depend on short- and long-term temperatures.
• The design method SOFA assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by filling
the gap with mortar of sufficient compressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means.
• The compliance with current standards (e.g. EC3) is the responsibility of the user
• An SLS-check is not performed for SOFA and has to be provided by the user!
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.6.1
Company: Page: 6
Specifier: Project: Riyadh Metro
Address: Sub-Project I Pos. No.: Case-2
Phone I Fax: | Date: 11/1/2015
E-Mail:
8 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-HY 200 + Rebar 20mm
Profile: no profile Installation torque: 0.000 kNm
Hole diameter in the fixture: df = 20 mm Hole diameter in the base material: 25 mm
Plate thickness (input): 1 mm Hole depth in the base material: 365 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 415 mm
Cleaning: Premium cleaning of the drilled hole is required
110 110 25
12 13
168
10 11
168
625
8 9
168
6 7
168
4 5
168
2 3
625
168
16 1
168
14 15
49
30 155 35
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.com Profis Anchor 2.6.1
Company: Page: 7
Specifier: Project: Riyadh Metro
Address: Sub-Project I Pos. No.: Case-2
Phone I Fax: | Date: 11/1/2015
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan