Professional Documents
Culture Documents
362'' wall EU
Grade: S-135
Drill Pipe Performance Sheet Range: 2
Asset Number: WS36-01 Tool Joint: 3.875'' x 2.156'' 2 7/8" AOH
Tensile Strength (lbs): 385,820 363,889 342,236 299,763 Upset Type: EU Fluid Capacity w/o IPC (gal/ft): 0.18
Torsional Strength (ft-lbs): 20,798 19,547 18,321 15,945 Max Upset OD (in): 3.188 Fluid Capacity w/o IPC (bbls/ft): 0.0043
Drift Size (in): 2.031
Burst Capacity (psi): 29,747 32,297 30,597 27,197
Collapse Capacity (psi): 29,716 28,746 27,739 25,602
Note: These are OEM values that may vary with actual values due to mill tolerances, IPC tolerances, OEM rounding, and other
Notes: Body properties are calculated based on uniform OD and wall thickness. factors. Pipe is purchased at a guaranteed 95% RBW. IPC is applied to a nominal thickness of 0.009''. Pipe will have an ID of
Burst capacity for Nominal (100% RBW) based on 87.5% RBW per API. 2.093'', which is smaller than pipe purchased at 87.5%.
The technical information contained herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical
information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various
inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices,
and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
www.workstringsinternational.com 05-Jun-20
Download the Workstrings International Pipe Specification App on the App Store℠ or Google Play™
Operational Limits of Drill Pipe
Connection 2-7/8 AOH (2-7/8 OH) Tool Joint OD (in) 3.875 Tool Joint ID (in) 2.156 Tool Joint Specified Minimum 120,000
Yield Strength (psi)
Pipe Body 80 % Inspection Class Pipe Body OD (in) 2.875 Wall Thickness (in) 0.362 Pipe Body Grade S-135
Combined Loading for Drill Pipe at Combined Loading for Drill Pipe at
Maximum Make-up Torque = 5,200 (ft-lbs) Minimum Make-up Torque = 4,300 (ft-lbs)
Operational Assembly Pipe Body Connection Max Operationa Assembly Pipe Body Connection
l Torque Max Tension Max Tension Max Tension
Torque Max Tension Max Tension Tension
(ft-lbs) (lbs) (lbs) (lbs) (ft-lbs) (lbs) (lbs) (lbs)
Connection
Make-up Torque Range
Make-up Torque Connection Max
(ft-lbs) Tension (lbs)
Min MUT 4,300 285,300
4,400 292,000
4,500 298,600
4,600 305,200
4,700 311,900
4,800 318,500
4,900 325,200
5,000 331,800
5,100 335,000
Max MUT 5,200 325,600
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box ID’s, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
06-18-2015
Makeup Torque Guidelines
- Good COPPER-BASED thread compound is recommended for rotary-shouldered drill pipe connections by the OEM.
- Be LIBERAL with the thread compound in the box, the base of the box, and on the pin using a copper-based or a
compatible thread compound.
- Ensure 360 DEGREES of coverage of the threads and torque shoulders.
- Ensure 360 DEGREES of coverage on the seal surfaces on completion pipe.
- Always ENSURE proper pipe alignment.
- ADJUST makeup torque according to thread compound Friction Factor (FF) greater than 1.0 FF up to 1.15 FF.
Workstrings Engineering is available for more information.
- MINIMIZE clamp pressure with the tongs or iron roughneck.
- MAXIMIZE the distance between the box shoulder and lower jaw die per OEM guidelines (1”-2” minimum for most
tool joints).
- Use a SLOW rotation speed during spin-up and break-out of the first 5-6 threads - especially critical for premium
and completion connections.
NOTE: More detailed running procedures for proprietary rotary-shouldered connections are available from the OEM’s website
www.workstringsinternational.com