Professional Documents
Culture Documents
8. GENERAL OBJECTIVE: the case study aids to evaluate the skill of candidate to study,
exploit, intervene into conception and realization of electrical equipment.
9. STRUCTURE OF THE SUBJECT:
SUBJECT SPECIALTY DIFFERENT PARTS DURATIO Workload MARKS
/ N ALLOCATED
OPTION
PART A: Electrical Machines 1H30 30% 30
CASE ELT PART B: Generation and 2H30 40% 40
STUDY Electrical installations
PART C: Power control and 2H00 30% 30
linear feedback
Page 1 of 10
Objective: this part, aids to evaluate the skill of candidate to:
Explain the organisation and the functioning of electrical machines;
Adapt a load to an electrical machine;
Exploit the characteristics of an electrical machine.
The machines of which investigation should be carried out are:
Static machines (single-phase and three-phase transformers);
Direct current machines;
Single-phase and three-phase asynchronous machines;
Single-phase and three-phase synchronous machines;
This part should be carried out at less on two different machines and related questions
such as:
Technological study;
Modelisation;
Functioning;
Estimation of powers.
PART B: Generation and Electrical installations
Duration: 2H30. Workload: 40% 40 Marks
Objective: this part, aids to evaluate the skill of candidate to:
Study and implement electrical equipment;
Dimensioning and choice of apparatus;
Power estimate of industrial system;
This part should be carried out at least on two sections that can be independent.
Section I: Generation and transmission lines.
This section should contain the following elements:
Technology of electrical power plant generation;
Elements of power plant dimensioning;
Architecture and equipment of a transmission network.
Section II: electrical installation.
This section should contain the following elements:
Lighting project (dimension of luminary, choice of apparatus);
Page 2 of 10
Study of electrical energy (power estimate, power factor correction, choice of
power transformer);
Dimensioning and choice of electrical apparatus;
Dimensioning and choice of canalisations;
Safety and protection.
PART C: Power control and linear feedback
Duration: 2H00. Workload : 30% 30 Marks
Objective: this part, aids to evaluate the skill of candidate to:
Describe the operation of a power converter;
Study on the technological plane and quantitative, a chain of production containing
static converters;
Explain the function of constitutive elements of a chain of regulation in industrial
section;
This part should be carried out at least on two sections that can be independent.
Section I: power electronic.
This section should contain the following elements:
The technology of components;
Study of power electronic static converters.
Section II: linear feedback.
This section should contain the following elements:
- Analysis of linear linear control system;
- characterization of linear control system;
- PID regulator for linear feedback control systems.
11.EVALUATION CRITERIA
The base of the evaluation will be focus on the following elements:
Calculations exactitude (literal statement should be allocated 50% of mark for the
question and 50% for the final result);
Presentation of tables, curves or graphs and diagrams;
Method used, clear definitions and pertinent analysis.
NB: the subject should be accompanied by its marking guide well structured.
Page 3 of 10
ELECTRONIC FOR ELECTROTECHNICs
1- SUBJECT ENTITLED: Electronic for Electrotechnics
2- TYPE OF PAPER: Professional
3- NATURE OF THE PAPER: Written paper.
4- TIME ALLOWED: 04 Hours
5- CREDIT: 06
6- TOTAL MARKS: 60
7- INSTRUCTIONS
c) Instructions to be respected by the candidate
- Precise the documents and the materials allowed.
d) Instruction to be respecter by the designer of the question paper.
- Precise the number of Annex join to the subject;
- The number of pages following the model X over Y.
Page 4 of 10
Analog filters or sinusoidal oscillators: 15% 9 Marks.
Page 5 of 10
AUTOMATION AND INDUSTRIAL COMMUNICATION PAPER
8. GENERAL OBJECTIVE:
Conceive an automation system, using industrial programmable logic controller
(PLC);
Be familial with industrial communication tools.
9. STRUCTURE OF THE SUBJECT:
SPECIALTY DIFFERENT PARTS DURATION WORKLOAD MARKS
/ ALLOCATED
OPTION
PART A: Industrial automatism 3H 70% 45
ELT PART B: Knowledge on industrial 1H 30% 15
communication
Page 6 of 10
Objective: this part, aids to evaluate the candidate skill to conceive and implement
sequential automatism and PLC.
The following aspects should be targeted:
Flow charts:
- Flow chart level I;
- Flow chart level II (viewed at the control point of the system);
- Viewed at the operating part.
Technology of the materialization:
- Sensors;
- Pre-actuators;
- Actuators;
- Circuits diagrams.
Programming of PLC.
Wiring of PLC.
Objective: this part aids to evaluate, the theoretical knowledge of the candidate within an
industrial communication environment.
Industrial networks: 30 Min. Workload: 15% 7 Marks
Topology of local Ethernet Network;
Industrial application of Ethernet networks;
Standard communication on Area network;
Network functionalities;
International standard;
Interconnection networks.
Data communication: 30 Min. Workload: 15% 8 Marks
Page 7 of 10
Model OSI (OSI layer model solicited in industrial communication network);
10.Evaluating criteria:
The evaluation is based on the following aspects:
- Exactitude of literal statement;
- Respect of graphics standard;
- Presentation of tables, curves and diagrams;
- Methodology used, clean definitions and pertinence analysis.
NB:
o precise if this paper has Annex, abacus or datasheet;
o precise the allowed documents, excluding the ones given by the examiner;
o The questions paper should be accompanied with a well elaborated marking guide.
Page 8 of 10
ELECTROTECHNICS PRACTICAL WORKS PAPER
1- SUBJECT ENTITLED: ELECTROTECHNICS PRACTICAL WORKS.
2- TYPE OF PAPER: PROFESSIONNAL SUBJECTS
3- NATURE OF THE PAPER: PRACTICAL
4- TIME ALLOWED: 05 Hours
5- CREDIT:08
6- TOTAL MARKS: 100
7- INSTRUCTIONS
a- Instructions to be respected by the candidate
- Precise the documents and the materials allowed.
b- Instruction to be respecter by the designer of question paper.
- Precise the number of Annex join to the subject;
- The number of pages following the model X over Y.
c- Precise the cutting list of materials as separated document.
Page 9 of 10
observe.
PART C: Report.
- Results table; 60 Min. 20% 20
- Plotting of curve.
- Results and analysis.
11.Evaluating criteria:
The evaluation is based on the following aspects:
- Mastering of the topic (Preparation) 30%
- Organisation of the working post (safety rules and implementation) 10%
- Execution (Wiring, measure, testing, etc.) 40%
- Interpretation (report) 20%
Page 10 of 10