Professional Documents
Culture Documents
1. There are sheet metal troughs with hinged or removable covers for housing and
protecting electrical wires and cables and in which conductors are laid in place.
A. Bus ways
B. Wire ways
C. Cable ducts
D. Cable trays
3. When tightening a terminal screw connection, the end of the wire should pass around
the screw in the same direction as the screw is turned so that
B. Enclosure
C. Panel board
D. Switch gear
A. Conduit
B. Fittings
C. Expander
D. Tighteners
6. Why is if necessary to use torque wrench in tightening bottled joints of copper bus bars
inside bus ducts and bus ways?
A. PVC
B. EMT
C. RSC/RMC
D. Flex Conduit
8. What is the types of fitting commonly used for exposed conduit support?
A. Conduit strap/Clamp
B. Condulet
C. Connector
E.
A. Sealed
B. Bonded
C. Grounded
D. Isolated
B. Such work will not impair any part of the existing installation
12. The size of circuit breaker to be used in 40 A motor full load current is
D. Equal to 100AT
15. The material used in long length bus bar joints to give allowance for thermal expansion
is____________
16. The current is directly proportional to the voltage and inversely proportional to
resistance.
A. Lenz’s Law
B. Power Law
C. Faraday’s Law
D. Ohm’s Law
17. Before adding to or altering an installation, you must ensure that
A. Partially tightened
B. Loosely installed
18. What amount of current will be drawn by incandescent bulb connected to a 115-volt
circuit if its resistance is 264.5 ohms?
A. 0.45 amps.
B. 0.43 amps.
C. 0.42 amps.
D. 2.3 amps.
19. When measuring ballast resistance if it is defective o good, it is necessary that the
source.
A. Energized
B. de-energized
C. unloaded
D. loaded
21. The 24 hours protection from home and commercial building to monitor and access
the video any time anywhere on this device.
D. CCTV Camera
22. The Auxiliary device of CCTV that monitor the motion daily.
A. Camera
B. Recorder
C. Monitor
D. Adapter
B. Exit Button
24. A part Auxiliary device that capture live events and save as video files
A. Power splitter
B. Camera
C. Monitor
D. Recorder
25. The minimum size of conduit commonly used in laying-out of Auxiliary Devices
A. ½” diameter
B. ¾” diameter
C. ½” PVC molding
D. ¾” PVC molding
26. An electricians should always have his tools in good working condition, the most
important reason being is__________
27. What type of hand tools commonly used in boring of ½” diameter hole in panel board
D. Hand drill
28. It is the connection between the grounded circuit conductor and the equipment
grounding conductor at the service.
A. Bonding jumper
29. What is the fitting commonly used for tightening between the boxes the RSC conduit?
A. Straight Connector
B. Condulet
C. Conduit strap
30. Part of the Auxiliary System that set the motion-trigger action individually for each
camera.
A. Live Previewing
B. Recording
C. Camera Scheduled
D. Motion detection
A. Wiring diagram
B. Schematic diagram
C. Pictorial drawing
D. Electrical lay-out
2. Which of the following electrical parameters apply or labelled to all kind of awitches?
A. Rated power and rated voltage
3. When tightening a terminal screw connection with the splice wire, the end of the splice
wire should pass around the screw in the same direction as the screw is turned, so
that_________
A. Conduit
B. Fittings
C. Expander
D. Tighteners
A. PVC
B. EMT
C. Flex Conduit
D. RSC/IMC
7. What do you call a fitting resembling a pipe with a removable cover access to electric conduit?
A. Conduit strap/Clamp
B. Condulet
C. Connector
D. Lock nut and bushing
A. Splice Box
B. Full Box
C. Square Box
D. Utility Box
9. A mechanical connector that is crimped unto a conductor for both splice and termination is
known as
B. Solderless connector
C. Mechanical lug
D. Bolt connector
A. PVC Cement
B. PVC Solvent
C. PVC Varnish
D. PVC Adhesive
11. The size of circuit breaker to be used in 40 A motor full load current is
C. Less than 50 AT
D. Equal to 100AT
12. A live duplex wire can be de-energized quickly and safely by cutting ______.
A. 35 amperes
B. 20 amperes
C. 25 amperes
D. 50 amperes
16. What will you do if the load schedule a 20AT/2.0-sq.mm.Lighting Branch Circuit of which
circuit breaker is over rated?
17. What amount of current will be drawn by incandescent bulb connected to a 115-volt circuit if
its resistance is 264.5 ohms?
A. 0.45 amps.
B. 0.43 amps.
C. 0.42 amps.
D. 2.3 amps.
18. When measuring ballast resistance if it is defective or good, it is necessary that the source
A. Energized
B. De-energized
C. Unloaded
D. Loaded
20. It is the connection between the grounded circuit conductor and the equipment grounding
conductor at the service.
A. Bonding jumper
B. Exit Button
D. Magnetic Lock
22. The technical term for the type THW wires mostly is industrial wirings is
D. Plastic Covering
23. Which of the following is the input device
A. Door Lock
B. Exit Button
24. When skinning a small wire, the insulation should be “ pencil down” rather that cut squire to
25. The minimum size of conduit commonly used in laying-out of Auxiliary Devices
A. ½” diameter
B. ¾” diameter
C. ½” PVC molding
D. ¾” PVC molding
26. An electricians should always have his tools in good working condition, the most important
reason being is ______
27. What type of hand tool commonly used in boring of ½” diameter hole in a panel board
D. Hand drill
28. There are sheet metal troughs with hinged or removable covers for housing and protecting
electrical wires and cables and ion which conductors are laid in place.
A. Bus ways
B. Wire ways
C. Cable ducts
D. Cable trays
29. What are the types of fitting commonly used for tightening between the boxes and the
conduit?
A. Straight Connector
B. Condulet
C. Conduit strap
A. Splice box
B. Full Box
C. Square Box
D. Utility Box
Set C
1. C
2. B
3. B
4. B
5. C
6. C
7. B
8. a
9. B
10. B
11. B
12. D
13. C
14. D
15. b
16. c
17. C
18. C
19. B
20. B
21. D
22. A
23. B
24. D
25. B
26. D
27. D
28. A
29. D
30. B