Professional Documents
Culture Documents
06 - 772 55211 Sxxa Tnbe
06 - 772 55211 Sxxa Tnbe
% !#%% (% &% (#%% &% #+% #
%
&% &$ &% %$ %%$
#%$ #$#' $$ !* %$
$&# $ ! $% $ # !& &%$ "&!! (% % $$#* &%$ % &
!% #$% ## &%!)#
$1 2 3 4 5 6 7 8 9 10 11 12 13
+5V
Note If the equipment is controlled by a CNCC, it has to be noted that a CNCC address can only be
assigned to position 12, refer also to strap fields and, for detailed information, to section 3 of the
manual (Installation). So, no slave PCM controller unit or APS unit should be mounted on the
subrack in case of CNCC control.
/8
772 55211 First order multiplexer subrack
SXXA
PS CS AL MTL1 MTL2 CL
Black Yellow-green
Black Brown
Red Blue
Piercing terminal
(code 770 14600 AFUA)
Cable 772 55103 AAAA
from Subrack
to power bus *1 See backpanel connector +5V
If the subrack is equipped in a module without distribution cable, the subrack power is connected as shown
below :
+5V -5V
PS CS AL MTL1 MTL2 CL
/8
+5V
+5 V connector, connected on only one first order multiplexer subrack to the power distribution cable
772 55102 AXAA for the +5 V supply to the alarm subrack, if an alarm subrack is used and if there is no
DC/DC converter on the alarm subrack.
-5V
-5 V connector.
AL
Alarm bus output connector for remote alarm supervision system. The signals on this connector depend on
the PCMC variant :
D PCMC : 772 52102 BBBA / 3AL 43018 BXXX
The open collector alarm output is active (low impedance with respect to ARTN=ground) in case of
alarm on the system.
MTL1
Multiple connector 1 (through-connection between subracks) : this connector can be used as follows :
D used for the connection of a +48 V supply for some signalling units if provided;
D if the optional TEST-E unit 772 52126 AAAA is equipped on one subrack of the module, see section 4
of the manual (operation), it is used for the through-connection of the test bus :
Meaning :
D TPCM system :
Signal 2 : +48V : positive battery supply for some CSUs (if provided) via cable 772 55149
Signal 3 - 4 - 5 : not connected
D SPCM system :
exchange :
- Signal 2 : not connected
- Signal 3 : TBA : test bus A-wire
- Signal 4 : TBB : test bus B-wire
- Signal 5 : TBF : test bus free indication wire
subscriber :
- Signal 2 : not connected
- Signal 3 : TBA : test bus A-wire
- Signal 4 : TBB : test bus B-wire
- Signal 5 : ALARM : ringing generator alarm
/8
772 55211 First order multiplexer subrack
SXXA
Meaning :
D TPCM system : Signal 0 - 1 - 6 : not connected
D SPCM system :
- exchange : Signal 0 - 1 - 6 : not connected
- subscriber :
- Signal 0 : RBR : ring bus ring lead
- Signal 1 : RBT : ring bus tip lead
- Signal 6 : not connected
CL
Clock signal connector :
Meaning :
D C2OT-C2OF : system clock output
D ECLKIT-ECLKIF : external synchronization clock input
By means of straps on the PCM controller unit both the output and the input can be matched to 120 Ω
balanced or 75 Ω unbalanced. In the latter case the A-pins or the B-pins can be grounded (refer to the
strap options on the PCM controller unit).