Professional Documents
Culture Documents
27 - 3al 42923 Adaa Tnaaa
27 - 3al 42923 Adaa Tnaaa
ADXX
not permitted without written authorization from Alcatel.
document, use and communication of its contents
All rights reserved. Passing on and copying of this
1 Function
This subrack has 17 positions for plug-in units and can be equipped with the necessary
units to build 1 complete first order multiplexer system.
This variant is the non-EMC version of the subrack and can be used with board variants
without EMC frontplates (except the QEXA card), but equipped with stiffeners instead.
DOCC: *NA
MMCC: *NA
20031010
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
Q2LTS Manage
Alarm Lamp driver ment bus
3 Subrack equipment
The subrack is equipped as follows :
1 (main) ringer/power unit in position 8;
1 redundant ringer/power unit in position 7 (option);
1 (master) PCMC unit in position 15;
1 CNCC unit in position 16 (option);
1 Q1 extension unit QEXA in position 17 (option);
the positions 1 to 7 and/or 9 to 14 can be equipped with the necessary CSU's to build
1 multiplexer systems :
Test
2 connectors for the through-connection between subracks of the test bus (daisy-chain
principle) :
01 : Not connected
06 : Not connected
02 : SL3 : Signal 3
07 : Not connected
03 : SL4 : Signal 4
08 : Not connected
04 : Not connected
09 : Not connected
05 : Not connected
Meaning :
TPCM system : Signal 3 - 4 : not connected
SPCM system :
Signal 3 : TBA : test bus A-wire
Signal 4 : TBB : test bus B-wire
This connector can be used with the cable 3AL 42877 AAAA to connect the lamps on top of
the rack.
Q2
Q2 interface connector (only if a CNCC is provided in position 16) :
08 : Not connected
15 : Not connected
07 : Not connected
14 : Not connected
06 : Clock in (+)
13 : Clock in (-)
05 : Not connected
12 : Electrical ground
04 : Data out (+)
11 : Data out (-)
03 : Not connected
10 : Electrical ground
02 : Data in (+)
09 : Data in (-)
01 : Safety ground
POWER
Power supply connector, connected to the power distribution via a connection cable 3AL
42732.
B B B
A A A
T T T
2 R 1
5 Power unit
The power unit is used to :
interrupt the power supply (BAT1 and BAT2) either manually or automatically in case of
overcurrent.
protect the boards in this subrack from transients and surges on the battery power
supplies.
Note The addresses can also be set by means of switches on the backpanel of the
subrack : however, this method can only be used on the following conditions :
the CNCC is mounted on the subrack;
there is no need to extend the Q1 bus to other subracks;
the other functionalities of the QEXA unit (access for synchronization clock
input or output, access for auxiliary alarm inputs) are not required.
CLK 123
F X264
A
X266
Master Slave
E S678
S301 S401
D 1 1
2 2
3 3
4 4
5 5
GND 6 6
7 7
Open OUT IN 8 8
S246 ON S402ON
S7001 75Ω 120Ω 120 75Ω S302
S268 Ω
1 1
S286 S262 3
2 2
3
4 4 B
S285 ON ON
C S222 S524
S510
S221 64K 1200
Take care to select different groups by means of the switches of S301 and
ATTENTION S302.
As the switches of S302 can only select addresses below 32, it can be
appropriate to select the addresses above 32 with the switches of S301.
Value Value
8 1 1 5
24 2 2 6
S302 0 3 3 7 S402
16 4 4 8
Value Value
8 1 1 5
The addresses are assigned to the units on the subrack asS302
follows
24 :23 2 6
0 3 7 S402
16 8
the 1st address belongs to the PCM controller unit in position 15 and the main ringer
4 4
Value Value
8 1 1 5
24 2 2 6
S302 0 3 3 7 S402
16 4 4 8
Take care to select different groups by means of the switches of S301 and
ATTENTION S302.
As the switches of S302 can only select addresses below 32, it can be
appropriate to select the addresses above 32 with the switches of S301
Value Value
8 1 1 5
24 2 2 6
S302 0 3 3 7 S402
16 4 4 8
the 1st address belongs to the PCM controller unit in position 15 and the main
ringer power unit RGPA in position 8;
the 2nd address belongs to the unit in position 1 and the redundant ringer power
unit RGPA in position 7 or 16, if provided;
the 3rd address belongs to the unit in position 14;
the 4th address belongs to the unit in position 2;
the 5th address belongs to the unit in position 13;
the 6th address belongs to the unit in position 3;
the 7th address belongs to the unit in position 12;
the 8th address belongs to the unit in position 4;
group of addresses selected with S301 :
the 1st address belongs to the unit in position 11;
the 2nd address belongs to the unit in position 5;
the 3rd address belongs to the unit in position 10;
the 4th address belongs to the unit in position 6;
the 5th address belongs to the unit in position 9;
the 6th address belongs to the unit in position 7;
the 7th address belongs to the unit in position 8;
the 8th address is not used.
The unit in position 1 to 14 can be a Slave PCM controller or ILTAUS.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
S700
CNCC PWR
OFF ON
1
2
S701 3
4
OFF ON
If the address setting is realized on 1
2
the QEXA unit, these switches have S702
3
4
to be open (as shown) !! 5
6
7
8