Professional Documents
Culture Documents
恒隆广场主塔楼施工中的应用
段 海 汪晓阳 张希博
( 中建钢构有限公司,沈阳 110000)
摘 要: 在水平荷载起控制作用的超高层建筑中,设置伸臂桁架可以提高结构的整体工作性能,从而提
高结构的抗侧刚度,控制结构的顶部位移,降低核心筒所承担的倾覆力矩。但是,伸臂桁架在施工阶段,由于
内外筒施工不同步,结构布置不对等原因,会导致施工过程中内、外筒的变形存在一定差异,如果盲目施工,
将会造成在伸臂桁架内部过早产生较大应力,导致结构成形后整体受力状况与原结构设计模型不符。通过
研究,提出一种超高层伸臂桁架“延迟连接”的施工技术。该方法在沈阳恒隆广场主塔楼施工应用的情况表
明,可有效解决外框与芯筒不均衡变形导致的伸臂桁架应力过大的问题,确保了伸臂桁架施工和使用阶段的
结构性能。
关键词: 超高层; 伸臂桁架; 延迟连接; 内外筒不均衡变形
DOI: 10. 13204 / j. gyjz201411028
Abstract: As the horizontal load is the dominant factor for a super tall building,setting outrigger can improve the
overall performance of the structure,so as to improve the lateral stiffness of the structure,control the displacement on
top of the structure,and reduce overturning moment that core tube bears. However,when the outrigger trusses are in
construction stage,the rate of progress of construction between the frame and core tube is not synchronous and
structure arrangement is unequal etc,which will lead to uneven deformation between the frame and core tube. If the
outrigger trusses are blindly installed,a greater internal stress will be generated in outrigger truss,which may cause
the bearing condition of the whole structure can not match the original structure design model after the structure is
finished. It was proposed a“delay connection”construction technology of outrigger truss for super tall buildings,and
the use of this method in the construction of the main tower of Shenyang Henglong Plaza showed that it could
effectively solve the problem of more stress generated in outrigger truss that caused by the uneven deformation between
the frame and core tube; and also ensured the smooth installation of outrigger truss and the structural performance in
the using stage.
Keywords: super tall buildings; outrigger truss; delay connection; uneven deformation between frame and core tube
1 问题的起源 施工阶段,由于结构是逐层施工,荷载的加载方式为
随着建筑行业的快速发展,
300 m 以上的超高层 逐层加载,与设计时的一次性加载有所不同,再加上
建筑不断涌现。在水平荷载起控制作用的超高层建 超高层建筑施工过程中,核心筒普遍领先于外框架
筑中,
设置伸臂桁架可以提高结构的整体工作性能, 施工,内、外筒结构布置相差较大,内、外筒竖向结构
从而提高结构在风荷载、
地震作用等水平作用下的抗 的应力、应变的增长速度随时间的变化不同 ,导致施
工过程中内、外筒的变形不可避免地存在一定差异 。
侧刚度,
控制结构的顶部位移和核心筒所承担的倾覆
力矩。目前国内外超过 300 m 以上的超高层建筑普 第一作者: 段海,男,
1981 年出生,工程师。
遍采用“带伸臂桁架的钢框架 - 芯筒”结构体系。 电子信箱: gjg-hl@ 163. vip. com
但是,对于该体系在结构未成形之前,即结构在 收稿日期: 2014 - 03 - 27
图5 伸臂桁架安装流程
Fig. 5 The flow chart of erecting the outrigger truss
3. 4 “延迟连接”节点焊接固定工艺
—◆—外框架; —■—核心筒; —▲—变形差 由于“延 迟 连 接 ”节 点 的 后 焊 封 板 厚 度 达
图4 施工全过程变形模拟分析 100 mm,且为超长焊缝,长度约 7. 2 m,因此“延迟
Fig. 4 Simulation of the deformation in the process of construction
连接”节点的焊接固定工艺尤为关键。 在焊接固定
通过施工全过程模拟分析计算,掌握伸臂桁架 过程中,应遵循以下焊接工艺原则:
安装前后内、外筒变形差值的变化规律,从而确定伸 1) 对称焊接原则,同一个剖面位置的两条对称
测点 18; 测点 19
图9 应力监测数据分析
Fig. 9 Analysis of stress monitoring data
由图 9 可见,
伸臂桁架焊接前应力很小,
焊接后应
1—①号焊缝; 2—②号焊缝; 3—焊接约束板; 4—外框柱;
力有明显增加, 但增幅不大,
且该部分增加应力主要由
5—100 mm 厚封板( 后焊) ; 6—添加适当的楔形钢垫板
( 递进减小板厚) 焊接残余应力造成。因而确定该技术所提出的伸臂桁
图7 焊接工艺示意 架“延迟连接”施工技术能真实地模拟结构力学模型,
Fig. 7 The graph of welding process 伸臂桁架基本未受到施工阶段内外筒变形差的影响。
3. 5 现场变形监测
4 结 语
在“延迟连接”节点位置的外框牛腿和 U 型槽上
以沈阳茂业中心、深圳京基金融中心、沈阳市府
分别设置监测点,在监测点位置做好永久性标记,并
恒隆广场等多个大型重点工程的伸臂桁架施工实践
记录好初始标高。采用全站仪对“延迟连接”节点两
为基础,创建了伸臂桁架“延迟连接 ”的成套施工技
外筒的竖向变形进行监测,
侧内、 根据监测得到的内、
术,其中包含了基于施工仿真模拟与现场变形监测
外筒变形差值调节 U 形节点上、
下钢垫板的数量。
互相校核的伸臂桁架延迟焊接技术与实时应力监测
变形监测数据显示,随着施工的进展,内、外筒
技术,解决了外框与芯筒不均衡变形导致的伸臂桁
均有不同程度的竖向变形,且内、外筒的竖向变形存
架应力过大难题,确保了伸臂桁架施工与使用阶段
在一定差值,如图 8 所示。
的结构性能,为超高层建筑施工中伸臂桁架的延迟
连接提供了一种实用而有效的新方法 。
参考文献
[1] 刘曙,陆建新,刘晓斌,等. 深圳京基 100 大厦 441. 8 m 伸臂桁
架安装技术[J]. 钢结构, 28( 2) : 68 - 71.
2013,
[2] 刘畅,黄用军,何远明,等. 伸臂桁架工作性能研究和设计建议
[J]. 建筑结构,
2013( 9) : 57 - 61.
[3] 李勇,管昌生,程骥,等. 巨柱框架 - 核心筒 - 伸臂桁架结构体
系施工过程的动态模拟[J]. 工业建筑, 43( 5) : 9 - 13.
2013,
—◇—核心筒; —□—外框 [4] 林同炎,斯多台斯伯利. 结构概念和体系[J]. 2 版. 高立人,
图8 现场变形监测数据分析 译. 北京: 中国建筑工业出版社,
2002.
Fig. 8 Analysis of deformation monitoring data on site [5] GB 50017—2011 钢结构设计规范( 报审) [S].
[6] GB 50755—2012 钢结构工程施工规范[S].