Professional Documents
Culture Documents
PART 1 GENERAL
1.1 SUMMARY
A. Section includes pipe, pipe fittings, connections and equipment for sanitary sewer
piping systems. This section also includes floor drains, cleanouts, interceptors,
manholes and sewage ejectors.
B. Related Sections:
1. Pipes and Tubes
2. Concrete Forms and Accessories: Execution requirements for placement
of inserts and sleeves specified by this section.
3. Cast-in-Place Concrete: Execution requirements for placement of concrete
specified by this section.
4. Paints and Coatings: Execution requirements for painting material
specified by this section.
5. Mechanical Identification: Product requirements for pipe identification for
placement by this section.
6. Wiring Connections: Execution requirements for electric connections to
equipment specified by this section.
7. Motors: Product requirements for motors for placement by this section.
1.2 REFERENCES
F. ASTM A53 - Pipe, Steel, Black and Hot-Dipped Zinc Coated, Welded and
Seamless.
J. ASTM C14 - Concrete Sewer, Storm Drain, and Culvert Pipe (ASTM C14M -
Concrete Sewer, Storm Drain, and Culvert Pipe Metric).
K. ASTM C425 - Compression Joints for Vitrified Clay Pipe and Fittings.
L. ASTM C564 - Rubber Gaskets for Cast Iron Soil Pipe and Fittings.
M. ASTM C1053 - Borosilicate Glass Pipe and fittings for Drain, Waste, and Vent
(DWV) Applications.
O. ASTM D2564 - Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Pipe
and Fittings.
R. ASTM D2665 - Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe
and Fittings.
S. ASTM D2729 - Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings.
X. ASTM D3034 - Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings.
AA. ASTM D4160 - Reinforced Thermosetting Resin Pipe (RTRP) Fittings for Non-
Pressure Applications.
CC. ASTM F477 - Elastomeric Seals (Gaskets) for Joining Plastic Pipe.
EE. ASTM F679 - Poly (Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity
Sewer Pipe and Fittings.
HH. CISPI 301 (Cast Iron Soil Pipe Institute) - Cast Iron Soil Pipe and Fittings for
Hubless Cast Iron Sanitary Systems.
II. CISPI 310 (Cast Iron Soil Pipe Institute) - Joints for Hubless Cast Iron Sanitary
Systems.
JJ. MSS SP58 (Manufacturers Standardization Society of the Valve and Fittings
Industry) - Pipe Hangers and Supports - Materials, Design and Manufacturer.
KK. SP89 - Pipe Hangers and Supports - Fabrication and Installation Practices.
MM. PDI G-101 (Plumbing and Drainage Institute) - Testing and Rating Procedure for
Grease Interceptors with Appendix of Sizing and Installation Dat
1.3 SUBMITTALS
B. Product Data: Submit data on pipe materials, fittings, and accessories. Submit
manufacturers catalog information. Indicate component sizes, rough-in
requirements, service sizes, and finishes. Indicate pump type, capacity, power
requirements, certified pump curves showing pump performance characteristics
1.5 QUALIFICATIONS
A. Product Requirements.
1.10 WARRANTY
B. Furnish five year manufacturer warranty for sanitary waste and vent piping.
PART 2 PRODUCTS
C. PVC Pipe: ASTM D1785 Schedule 40, or ASTM D2241 SDR-26 for not less than
150 psi pressure rating.
1. Fittings: ASTM D2466, PVC.
2. Joints: ASTM D2855, solvent weld with ASTM D2564 Solvent cement.
A. Drain, Waste, and Vent: Conform to ASME B31.9, ASTM F708,MSS SP58,MSS
SP69,MSS SP89.
B. Hangers for Pipe Sizes 1/2 to 1-1/2 inch malleable iron, Carbon steel, adjustable
swivel, split ring.
C. Hangers for Pipe Sizes 2 inches and Over: Carbon steel, adjustable, clevis.
D. Multiple or Trapeze Hangers: Steel channels with welded spacers and hanger
rods.
F. Wall Support for Pipe Sizes over 3 inches Welded steel bracket and wrought steel
clamp.
H. Floor Support: Cast iron adjustable pipe saddle, lock nut, nipple, floor flange, and
concrete pier or steel support.
B. General Purpose Vibration Resistant Fire Stopping Sealant: Silicone based, non-
slumping, premixed sealant with in tumescent properties, vibration and moisture
resistant, rated for 3 hours in accordance with ASTM E814 and UL 1479.
C. DWV Plastic Pipe Systems Fire Stopping Sealant: Silicone based, premixed
sealant with in tumescent properties, vibration and moisture resistant, rated for 3
hours in accordance with ASTM E814 and UL 1479 with metal collars.
A. Manufacturers:
1. Terain
2. Jason
Or approved equal
B. Floor Drain (FD-1): ANSI A1121.1; galvanized cast iron two piece body with
double drainage flange, weep holes, reversible clamping collar, and round,
adjustable nickel-bronze strainer.
C. Floor Drain (FD-2): ANSI A1121.1; galvanized cast iron two piece body with
double drainage flange, weep holes, [reversible clamping collar, and round,
adjustable round or square nickel-bronze strainer with removable perforated
sediment bucket.
D. Floor Drain (FD-3): ANSI A1121.1; galvanized cast iron two piece body with
double drainage flange, weep holes, reversible clamping collar, and round,
adjustable nickel-bronze strainer with polished bronze funnel
E. Floor Drain (FD-4): ANSI A1121.1; galvanized cast iron two piece body with
double drainage flange, weep holes, reversible clamping collar, and round,
adjustable nickel-bronze extra heavy duty strainer.
F. Floor Drain (FD-5): ANSI A1121.1; galvanized cast iron two piece body with
double drainage flange, weep holes, reversible clamping collar, and round,
G. Floor Drain (FD-6): Galvanized cast iron two piece body with drainage flange,
heavy duty grate 6 inches -12 inches wide, 12 inches -24 inches long, dome
strainer, end plates with gaskets.
A. Manufacturers:
1. Ideal Standard
2. Duravit
Approved or equal
B. Floor Sink (FS-1): Galvanized cast iron body with dome strainer and seepage
flange.
C. Floor Sink (FS-2): Square lacquered cast iron body with integral seepage pan,
epoxy coated interior, aluminum dome strainer, clamp collar, sediment bucket,
epoxy coated, nickel bronze frame and full grate.
A. Manufacturers:
1. Terain
2. Jason
Approved or equal
C. Strainer: Removable polyethylene, cast metal ,cast aluminum, cast bronze, cast
iron dome with stainless steel, bronze screen.
D. Accessories: Membrane flange and membrane clamp with integral gravel stops.
2.10 CLEANOUTS
A. Manufacturers:
1. Terain
2. Jason
Approved or equal
B. Exterior Surfaced Areas (CO-1): Round or Square cast nickel bronze access frame
and non-skid cover.
C. Exterior Unsurfaced Areas (CO-2): Line type with lacquered cast iron body and
round epoxy coated cover with gasket.
E. Interior Finished Wall Areas (CO-4): Line type with lacquered cast iron body and
round epoxy coated cover with gasket, and round stainless steel access cover
secured with machine screw.
2.11 SUMPS
A. Manufacturers:
1. Terain
2. Jason
Approved or equal
B. Construction:
1. Material: Epoxy coated fabricated steel
2. Rough in: Fully recessed in floor installation with anchor flange
D. Cover: Steel, epoxy coated, non-skid with gasket, securing handle, and enzyme
injection port, recessed for floor finish, tile, terrazzo
A. Manufacturers:
1. Jason
2. Terain
Approved or equal
B. Construction:
1. Material: Epoxy coated fabricated steel
2. Rough in: Fully recessed in floor installation with anchor flange.
D. Cover: Steel, epoxy coated, with gasket, securing handle, and enzyme injection
port , recessed for floor finish
A. Manufacturers:
1. Jason
2. Terain
Approved or equal
B. Epoxy coated cast iron, Stainless steel or Precast concrete body and secured cover
with removable stainless steel sediment bucket.
2.15 MANHOLES
A. Manufacturers:
1. Jason
2. Terain
Approved or equal
C. Casing: Cast iron volute with radial clearance around impeller, slide away
couplings
D. Impeller: Cast iron, Bronze; open non-clog, keyed to corrosion resistant alloy
steel stainless steel shaft.
E. Support: Cast iron pedestal motor support on steel floor plate with gas tight
gaskets.
F. Bearings: Oil lubricated bronze sleeve spaced maximum 48 inches and grease
lubricated ball thrust at floor plate.
H. Sump: Steel cover plate with steel curb frame for grouting into concrete sump
with inspection opening and cover, and alarm fittings.
I. Controls Float operated mechanical alternator with float rod, stops, and corrosion
resistant float to alternate operation of pumps. Cut-in second pump on rising level
or lead pump failure. Furnish separate pressure switch high level alarm with
transformer, alarm bell, and stand pipe ,and extra set of wired terminals for
remote alarm circuit and emergency float switch with float rod, stops, and
corrosion resistant float to operate both pumps on failure of alternator.
A. Manufacturers:
1. Jason
2. Terian
Or Approved equal
B. Casing: Cast iron or Bronze pump body and oil filled motor chamber.
C. Impeller: Cast iron; Bronze; open non-clog, stainless steel corrosion resistant
alloy steel] shaft.
F. Accessories: Oil resistant 6 foot cord and plug with three-prong connector for
connection to electric wiring system including grounding connector.
H. Controls: Integral diaphragm, mercury switch, type level controls with separate,
liquid-level, and control high level alarm.
3.1 EXAMINATION
3.2 PREPARATION
A. Ream pipe and tube ends. Remove burrs. Bevel plain end ferrous pipe.
3.3 INSTALLATION
E. Route piping in orderly manner and maintain gradient. Route parallel and
perpendicular to walls.
H. Install piping to allow for expansion and contraction without stressing pipe,
joints, or connected equipment.
I. Provide clearance in hangers and from structure and other equipment for
installation of insulation and access to valves and fittings.
J. Provide access where valves and fittings are not exposed. Coordinate size and
location of access doors
K. Establish elevations of buried piping outside building to provide not less than ft
of cover.
N. Prepare exposed, unfinished pipe, fittings, supports, and accessories ready for
finish painting.
R. Inserts:
1. Provide inserts for placement in concrete forms.
2. Provide inserts for suspending hangers from reinforced concrete slabs and
sides of reinforced concrete beams.
3. Provide hooked rod to concrete reinforcement section for inserts carrying
pipe over 4 inches
4. Where concrete slabs form finished ceiling, locate inserts flush with slab
surface.
5. Where inserts are omitted, drill through concrete slab from below and
provide through-bolt with recessed square steel plate and nut above flush
with top of recessed into and grouted flush with slab.
9. Prime coat exposed steel hangers and supports. Hangers and supports
located in crawl spaces, pipe shafts, and suspended ceiling spaces are not
considered expose
10. Install hangers adjacent to motor driven equipment with vibration
isolation; refer to Section 15070.
11. Support cast iron drainage piping at every joint.
T. Pumps:
B. Establish invert elevations, slopes for drainage to ¼ inch per foot percent
minimum. Maintain gradients.
3.5 SCHEDULES
G. All Sizes:
1. Maximum hanger spacing: 6 ft
2. Hanger rod diameter: 3/8 inch