Professional Documents
Culture Documents
Warehouse Struct
Warehouse Struct
C O N SU L T I N G
ENGINEERS
STRUCTURAL CALCULATIONS
31 pages
ARL
Principal Checked: ______
2020
Miller Consulting Engineers, Inc. was retained in a limited capacity for this
project. This design is based upon information provided by the client, who
is solely responsible for accuracy of same. No responsibility and or liability
is assumed by or is to be assigned to the engineer for items beyond that
shown on these sheets.
Basic Design
Loads:
Seismic Design
Design Summary:
Miller Consulting Engineers is responsible for the anchorage of the metal building to the foundation and the design of the foundation.
Loads from the metal building to the foundation have been provided to Miller Consulting Engineers by the metal building manufacturer Nucor.
Index of Calculations:
Design Summary Pg 1
Anchorage Design Pgs 2-19
Foundation Calculations Pgs 20-27
Appendix - foundation loads and plan Pgs 28-31
Anchor A Conditions:
1. wind to Left - (LRFD load combo: 0.9D+1.0W)
2. wind to right - (LRFD load combo: 0.9D+1.0W)
3. wind to front / back - (LRFD load combo: 0.9D+1.0W)
4. seismic to left - (LRFD load combo: (0.9-0.2Sds)D+omega*E)
5. seismic to right - (LRFD load combo: (0.9-0.2Sds)D+omega*E)
Condition 1:
D = 2 kips Load
Wind to left: 3 kips (uplift on roof)
Wind to left: 3 kips (uplift brace)
direction
Wind to left: 4 kips (lateral)
Vertical load: 0.9D + 1.0W = 0.9(2k) + 1.0 (6k) = 4.2 kips (up)
Lateral load = 5 kips
Conditions 2:
D = 2 kips Load
Wind to right: 3 kips (uplift on roof) direction
Wind to right: 3 kips (downward brace)
Wind to right: 5 kips (lateral)
Vertical load: 0.9D + 1.0W = 0.9(2k) + 1.0 (0k) = 1.8 kips (down)
Lateral load = 5 kips
Condition 3:
D = 2 kips Load
Wind to front: 3 kips (uplift on roof) direction
Vertical load: 0.9D + 1.0W = 0.9(2k) + 1.0 (3k) = 1.2 kips (up)
Lateral load = 1 kips
Condition 4:
D = 2 kips Load
Seismic to left: 2 kips (uplift brace)
Seismic to left: 3 kips (lateral)
direction
Vertical load: 0.77D + 2.5E = 0.77(2k) + 2.5 (2k) = 3.5 kips (up)
Lateral load = 2.5 (3) = 7.5 kips
Condition 5:
D = 2 kips Load
Seismic to left: 2 kips (downward brace)
Seismic to left: 3 kips (lateral) direction
Vertical load: 0.77D + 2.5E = 0.77(2k) + 2.5 (2k) = 6.5 kips (down)
Lateral load = 2.5 (3) = 7.5 kips
Anchor A
Conditions:
6. wind to Left - (LRFD load combo: 1.2D+1.6S)
Condition 6:
D = 2 kips Load
Snow = 1 kips
direction
Vertical load: 1.2D + 1.6S = 1.2(2k) + 1.6(1k) = 4 kips (down)
Hilti Summary and Utilization for Conditions 1-6 (3/4" dia anchor bolts, 16" embed)
supplemental reinforcement is not required
1. 19% - highest uplift - calculation on pages 5-6
2. 42%
3. 0%
4. 28%
5. 62% - highest shear - calculation on pages 7-8
6. 0%
Specifier's comments:
1 Input data
Anchor type and diameter: Hex Head ASTM F 1554 GR. 36 3/4
Effective embedment depth: hef = 16.000 in.
Material: ASTM F 1554
Proof: Design method ACI 318-11 / CIP
Stand-off installation: eb = 0.000 in. (no stand-off); t = 0.500 in.
Anchor plate: lx x ly x t = 8.000 in. x 14.000 in. x 0.500 in.; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, 3000, fc' = 3000 psi; h = 20.000 in.
Reinforcement: tension: condition B, shear: condition B;
edge reinforcement: none or < No. 4 bar
Input data and results must be checked for agreement with the existing conditions and for plausibility! 5 of 31
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
ANCHOR: A CONDITION 1
3 Warnings
• Please consider all details and hints/warnings given in the detailed report!
Input data and results must be checked for agreement with the existing conditions and for plausibility! 6 of 31
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
ANCHOR: A CONDITION 5
www.hilti.us Profis Anchor 2.7.5
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 3/12/2019
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: Hex Head ASTM F 1554 GR. 36 3/4
Effective embedment depth: hef = 16.000 in.
Material: ASTM F 1554
Proof: Design method ACI 318-11 / CIP
Stand-off installation: eb = 0.000 in. (no stand-off); t = 0.500 in.
Anchor plate: lx x ly x t = 8.000 in. x 14.000 in. x 0.500 in.; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, 3000, fc' = 3000 psi; h = 20.000 in.
Reinforcement: tension: condition B, shear: condition B;
edge reinforcement: none or < No. 4 bar
Input data and results must be checked for agreement with the existing conditions and for plausibility! 7 of 31
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
ANCHOR: A CONDITION 5
www.hilti.us Profis Anchor 2.7.5
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 3/12/2019
E-Mail:
3 Warnings
• Please consider all details and hints/warnings given in the detailed report!
Input data and results must be checked for agreement with the existing conditions and for plausibility! 8 of 31
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Design Concrete anchorage
Anchor E Conditions:
1. wind to Left - (LRFD load combo: 0.9D+1.0W)
Condition 1:
D = 4 kips Load
Wind to left: 10 kips (uplift on roof)
Wind to left: 3 kips (lateral)
direction
Vertical load: 0.9D + 1.0W = 0.9(4k) + 1.0 (10k) = 6.4 kips (up)
Lateral load = 3 kips
Hilti Summary and Utilization for Condition 1 (3/4" dia anchor bolts, 16" embed)
1. 11%
Anchor G Conditions:
1. wind to left (1.2D + 1.6S + 0.5W)
2. wind to left (1.2D + 1.0W + 0.5S)
3. wind to left (0.9D + 1.0W)
Condition 1:
Load
Vertical loads
D = 7 kips
direction
Roof live = 14 kips
Snow = 18 kips
Wind to left: 16 kips (uplift on roof)
Wind to left: 3 kips (uplift force brace)
Lateral loads
D = 4 kips
Roof Live = 7 kips
Snow = 9 kips
Wind to left: 9 kips
Vertical load: 1.2D + 1.6S + 0.5W = 1.2 (7) + 1.6 (18) + 0.5 (19) = 27.7 kips down
Lateral load: 1.2D + 1.6S + 0.5W = 1.2 (4) + 1.6 (9) = 19.2 kips
Lateral load: 1.2D + 1.6S + 0.5W = 0.5 (9) = 4.5 kips
Condition 2:
Vertical loads
D = 7 kips Load
Roof live = 14 kips direction
Snow = 18 kips
Wind to left: 16 kips (uplift on roof)
Wind to left: 3 kips (uplift force brace)
Lateral loads
D = 4 kips
Roof Live = 7 kips
Snow = 9 kips
Wind to left: 9 kips
Vertical load: 1.2D + 0.5S + 1.0W = 1.2 (7) + 0.5 (18) + 1.0 (19) = 1.6 kips up
Lateral load: 1.2D + 0.5S + 1.0W = 1.2 (4) + 0.5 (9) = 9.3 kips
Lateral load: 1.2D + 0.5S + 1.0W = 1.0 (9) = 9 kips
Condition 3:
Vertical loads
D = 7 kips
Wind to left: 16 kips (uplift on roof)
Wind to left: 3 kips (uplift force brace) Load
Lateral loads direction
D = 4 kips
Wind to left: 9 kips
Vertical load: 0.9D + 1.0W = 0.9 (7) + 1.0 (19) = 12.7 kips up
Lateral load: 0.9D + 1.0W = 0.9 (4) = 3.6 kips
Lateral load: 0.9D + 1.0W = 1.0 (9) = 9 kips
NCSD Technology & Information Services Metal Bldg Fdn 190220
9570 SW Barbur Blvd Project Name Project #
Suite One Hundred
Portland, OR 97219 4444 SE Lake Road, Milwaukie, OR
Location
BBL Architects
Client
MILLE R Phone 503.246.1250
BAM 3/4/19
C O N S U LT I N G Fax 503.246.1395
www.miller-se.com By Ck'd ARL Date Page 10 of 31
ENGINEERS
Design Concrete anchorage
Anchor G Conditions:
4. seismic to left: 0.9-0.2Sds)D+omega*E)
5. seismic to left: 1.2+0.2Sds)D+omega*E+0.2S)
Condition 4:
Load
Vertical loads
D = 7 kips direction
Roof live = 14 kips
Snow = 18 kips
Seismic to left: 1 kips (uplift)
Seismic to left: 2 kips (uplift force brace)
Lateral loads
D = 4 kips
Roof Live = 7 kips
Snow = 9 kips
Seismic to left: 2 kips
Condition 5:
Load
Vertical loads
D = 7 kips direction
Roof live = 14 kips
Snow = 18 kips
Seismic to left: 1 kips (uplift)
Seismic to left: 2 kips (uplift force brace)
Lateral loads
D = 4 kips
Roof Live = 7 kips
Snow = 9 kips
Seismic to left: 2 kips
Vertical load: 1.33D + 2.5E + 0.2S = 1.33(7) + 2.5 (3) + 0.2(18) = 5.4 kips down
Lateral load: 1.33D + 2.5E + 0.2S = 1.33 (4) + 0.2 (9) = 7.2 kips
Lateral load: 1.33D + 2.5E = 2.5 (2) = 5 kips
Anchor G Conditions:
6. wind to left (1.2D + 1.6S + 0.5W)
7. wind to left (1.2D + 1.0W + 0.5S)
8. 1.2D+1.6S
Condition 6:
Load
Vertical loads
D = 7 kips direction
Roof live = 14 kips
Snow = 18 kips
Wind to front: 15 kips (uplift)
Lateral loads
D = 4 kips
Roof Live = 7 kips
Snow = 9 kips
Wind to front: 4 kips
Condition 7:
Load
Vertical loads
D = 7 kips direction
Roof live = 14 kips
Snow = 18 kips
Wind to front: 15 kips (uplift)
Lateral loads
D = 4 kips
Roof Live = 7 kips
Snow = 9 kips
Wind to front: 4 kips
Condition 8:
Vertical loads
D = 7 kips
Snow = 18 kips
Lateral loads
D = 4 kips
Snow = 9 kips
Anchor G Conditions:
1. Check wind to Left - (LRFD load combo: 0.9D+1.0W)
2. Check wind to right - (LRFD load combo: 0.9D+1.0W)
3. Check wind to front / back - (LRFD load combo: 0.9D+1.0W)
4. Check seismic to left - (LRFD load combo: (0.9-0.2Sds)D+omega*E)
5. Check seismic to right - (LRFD load combo: (0.9-0.2Sds)D+omega*E)
Hilti Summary and Utilization for Conditions 1-8 (3/4" dia anchor bolts, 16" embed)
with supplemental anchor reinf.
1. 51% - calculation on concrete anchorage (pg 14-15)
2. 17%
3. 23% - calculation on concrete anchorage (pg 16-17)
4. 5%
5. 23%
6. 45%
7. 35%
8. 50% - calculation on concrete anchorage (pg 18-19)
Specifier's comments:
1 Input data
Anchor type and diameter: Hex Head ASTM F 1554 GR. 55 3/4
Effective embedment depth: hef = 16.000 in.
Material: ASTM F 1554
Proof: Design method ACI 318-11 / CIP
Stand-off installation: eb = 0.000 in. (no stand-off); t = 0.500 in.
Anchor plate: lx x ly x t = 14.000 in. x 8.000 in. x 0.500 in.; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, 3000, fc' = 3000 psi; h = 20.000 in.
Reinforcement: tension: condition B, shear: condition A; anchor reinforcement: shear
edge reinforcement: none or < No. 4 bar
(2) #5 hairpins
3 Warnings
• Please consider all details and hints/warnings given in the detailed report!
Input data and results must be checked for agreement with the existing conditions and for plausibility! 15 of 31
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
ANCHOR: G CONDITION 3
www.hilti.us Profis Anchor 2.7.5
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 3/6/2019
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: Hex Head ASTM F 1554 GR. 55 3/4
Effective embedment depth: hef = 16.000 in.
Material: ASTM F 1554
Proof: Design method ACI 318-11 / CIP
Stand-off installation: eb = 0.000 in. (no stand-off); t = 0.500 in.
Anchor plate: lx x ly x t = 14.000 in. x 8.000 in. x 0.500 in.; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, 3000, fc' = 3000 psi; h = 20.000 in.
Reinforcement: tension: condition B, shear: condition A; anchor reinforcement: shear
edge reinforcement: none or < No. 4 bar
Input data and results must be checked for agreement with the existing conditions and for plausibility! 16 of 31
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
ANCHOR: G CONDITION 3
3 Warnings
• Please consider all details and hints/warnings given in the detailed report!
Input data and results must be checked for agreement with the existing conditions and for plausibility! 17 of 31
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
ANCHOR: G CONDITION 8
Specifier's comments:
1 Input data
Anchor type and diameter: Hex Head ASTM F 1554 GR. 55 3/4
Effective embedment depth: hef = 16.000 in.
Material: ASTM F 1554
Proof: Design method ACI 318-11 / CIP
Stand-off installation: eb = 0.000 in. (no stand-off); t = 0.500 in.
Anchor plate: lx x ly x t = 14.000 in. x 8.000 in. x 0.500 in.; (Recommended plate thickness: not calculated
Profile: no profile
Base material: cracked concrete, 3000, fc' = 3000 psi; h = 20.000 in.
Reinforcement: tension: condition B, shear: condition A; anchor reinforcement: shear
edge reinforcement: none or < No. 4 bar
Input data and results must be checked for agreement with the existing conditions and for plausibility! 18 of 31
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
ANCHOR: G CONDITION 8
3 Warnings
• Please consider all details and hints/warnings given in the detailed report!
Input data and results must be checked for agreement with the existing conditions and for plausibility! 19 of 31
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
Design Thickened slab edge
Check along grid A (Grid A is the controlling case since reaction G has the highest loads and this
nce the bracing)
grid A also contains
Column A:
D=2k
S=1k
1.2D+1.6S = 4 kips
Column G:
D=7k
S = 18 k
1.2D+1.6S = 37.2 kips
Column D:
D=2k
S=4k
1.2D+1.6S = 8.8 kips
Output
Bar Size = #5
Bar Quantity = 5 bars
Layers = 1
As = 1.55 in² total
b= 27 in
h= 24 in
Clear dist. = 3 in
d= 20.69 in = 24-3-0.625*0.5
λ= 1.00
β1 = 0.85
a= 1.351 in
Mallowable = φMn = 139.6 ft-k > 72.5 ft-k OK
As, min. = 1.86 in² > 1.55, provide 1/3 greater steel than what is required
c= 1.59 in 139.6 > 96.7 (1/3 greater = 96.7) OK
εt = 0.0361 > 0.005, tension controlled
Bar Size = #5
Bar Quantity = 3 bars
Layers = 1
As = 0.93 in² total
b= 27 in
h= 24 in
Clear dist. = 3 in
d= 20.69 in = 24-3-0.625*0.5
λ= 1.00
β1 = 0.85
a= 0.810 in
Mallowable = φMn = 84.9 ft-k > 25.9 ft-k OK
As, min. = 1.86 in² > 0.93, provide 1/3 greater steel than what is required
c= 0.95 in 84.9 > 34.5 (1/3 greater = 34.5) OK
εt = 0.0621 > 0.005, tension controlled
Wind
direction
Check load combination 1.2D + 1.0W + 0.5S
Column A:
D=2k
S=1k
W = 6 kips (wind uplift) + 3 kips (brace down) = 3 kips uplift net
1.2D+1.0W+0.5S = 0.1 kips up
Column G:
D=7k
S = 18 k
W = 16 kips (wind uplift) + 3 kips (brace uplift) = 19 kips uplift net
1.2D+1.0W+0.5S = 1.6 kips up
Column D:
D=2k
S=4k
W = 6 kips (wind uplift)
1.2D+1.0W+0.5S = 1.6 kips up
These forces are low and will not control the foundation design
Wind
direction
Check load combination 0.9D + 1.0W
Column A:
D=2k
W = 6 kips (wind uplift) + 3 kips (brace down) = 3 kips uplift net
0.9D+1.0W = 1.2 kips uplift
Column G:
D=7k
W = 16 kips (wind uplift) + 3 kips (brace uplift) = 19 kips uplift net
0.9D+1.0W = 12.7 kips uplift
Column D:
D=2k
W = 6 kips (wind uplift)
0.9D+1.0W = 4.2 kips uplift
Resisting moments:
Thickened slab edge: 150 pcf x 2ft thick x 2.25ft wide x (45ft long edge x 4edges) x 45ft/2 arm = 2733 k-ft
Moment overturning:
Wind uplift = (16 kips at center x 2 columns x 45ft /2) + (6 kips at end wall x 2 columns x 45ft + 10 kips x 45ft) = 1710 k-ft
Wind lateral = (zone 1 + zone 4 = 20psf) x 45ft wide x 14.2ft tall x 7.1ft moment arm = 90 k-ft
*** PRELIMINARY REACTIONS ONLY - DO NOT USE FOR FINAL CONSTRUCTION!!! ***
This page covers the following frame lines:
1
GLOBAL X : POSITIVE INTO BUILDING (KIPS)
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL TYP INT
(LATERAL) C INT. INT. INT. A COLUMNS COLUMNS CORNER COLUMNS
Dead 0 B 0 0 B 0 0
Collateral Dead 0 0 0 0 0
Roof Live 0 0 0 0 0
Roof Snow* 0 0 0 0 0
Wind to Left 0 0 0 0 0
Wind to Right 0 0 0 0 0
Wind to Front 1 2 0 2 1
Wind to Back -1 -2 0 -2 -1
Seismic to Back 0 0 0 0 0
Seismic to Front 0 0 0 0 0
GLOBAL Y : POSITIVE UPWARD (KIPS)
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL TYP INT
(VERTICAL) C INT. INT. INT. A COLUMNS COLUMNS CORNER COLUMNS
Dead 1 B 1 0 B 1 1
Collateral Dead 1 2 0 2 1
Roof Live 1 5 0 5 1
Roof Snow* 1 7 0 7 1
Wind to Left -2 -5 0 -7 -3
Wind to Right -2 -8 0 -6 -1
Wind to Front -2 -9 0 -9 -2
Wind to Back -2 -9 0 -9 -2
Seismic to Back 0 0 0 0 0
Seismic to Front 0 0 0 0 0
GLOBAL Z : POSITIVE COUNTERCLOCKWISE (FT-KIPS)
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL TYP INT
INT. INT. INT. COLUMNS COLUMNS CORNER COLUMNS
Dead 0 0 0 0 0
Collateral Dead 0 0 0 0 0
Roof Live 0 0 0 0 0
Roof Snow*
Wind to Left
Wind to Right
Wind to Front
Wind to Back
0
0
0
0
0
REFERENCE ONLY
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Seismic to Back 0 0 0 0 0
Seismic to Front 0 0 0 0 0
BASE PLATE AND ANCHOR BOLT INFORMATION
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL COLUMNS
INT. INT. INT. COLUMNS COLUMNS CORNER TYPICAL
Base Plate Width 8.00 8.00 0.00 8.00 8.00
Base Plate Length 14.00 14.00 0.00 14.00 14.00
Anchor Bolt Quantity 4 4 0 4 4
Anchor Bolt Diameter 0.75 0.75 0.00 0.75 0.75
BRACING REACTIONS
BRACING
(KIPS) CONDITION: NUM OF BRACED BAYS: 0
(NOTE: BRACING GLOBAL X LOADS ARE PERPENDICULAR TO FRAME GLOBAL X LOADS)
(NOTE: FOR WALLS WITH AN X BRACING CONDITION,BRACING GLOBAL Y LOADS ARE ADDITIVE TO FRAME GLOBAL Y
GLOBAL
LOADS)X : POSITIVE TO RIGHT ENDWALL INPLANE BRACING
LEFT COL. RIGHT COL.** LEFT COL. RIGHT COL.
Wind to Front 0 0 0 0
Wind to Back -4 (LATERAL) -4 0 0
Seismic to Front 0 0 0 0
Seismic to Back -3 -3 0 0
GLOBAL Y : POSITIVE TO UPWARD ENDWALL INPLANE BRACING
LEFT COL. RIGHT COL. LEFT COL. RIGHT COL.
Wind to Front +/- 3 +/- 3 0 0
Wind to Back +/- 3 +/- 3 0 0
Seismic to Front +/- 2 (VERTICAL) +/- 2 0 0
Seismic to Back +/- 2 +/- 2 0 0
*(The Snow Reaction provided is the maximum of: Roof Snow, Unbalanced Snow, and User Override Snow.)
** The user must combine the lean to bracing reactions with supporting building bracing reactions.
Endwall bracing is not included in these reactions.
28 of 31
Building: Main
*** PRELIMINARY REACTIONS ONLY - DO NOT USE FOR FINAL CONSTRUCTION!!! ***
This page covers the following frame lines:
2
GLOBAL X : POSITIVE TO RIGHT (KIPS)
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL TYP INT
H INT. INT. INT. COLUMNS COLUMNS CORNER COLUMNS
(LATERAL)
Dead 2 0 0 0
G -2
Collateral Dead 2 0 0 0 -2
Roof Live 7 0 0 0 -7
Roof Snow* 9 0 0 0 -9
Wind to Left -4 0 0 0 9
Wind to Right -9 0 0 0 4
Wind to Front -6 0 0 0 4
Wind to Back -4 0 0 0 6
Seismic to Right -2 0 0 0 -2
Seismic to Left 2 0 0 0 2
GLOBAL Y : POSITIVE UPWARD (KIPS)
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL TYP INT
H INT. INT. INT. COLUMNS COLUMNS CORNER COLUMNS
(VERTICAL)
Dead 3 0 0 0
G 3
Collateral Dead 4 0 0 0 4
Roof Live 14 0 0 0 14
Roof Snow* 18 0 0 0 18
Wind to Left -12 0 0 0 -16
Wind to Right -16 0 0 0 -12
Wind to Front -13 0 0 0 -15
Wind to Back -15 0 0 0 -13
Seismic to Right -1 0 0 0 1
Seismic to Left 1 0 0 0 -1
GLOBAL Z : POSITIVE COUNTERCLOCKWISE (FT-KIPS)
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL TYP INT
INT. INT. INT. COLUMNS COLUMNS CORNER COLUMNS
Dead 0 0 0 0 0
Collateral Dead 0 0 0 0 0
Roof Live 0 0 0 0 0
Roof Snow*
Wind to Left
Wind to Right
Wind to Front
0
0
0
0
REFERENCE ONLY
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Wind to Back 0 0 0 0 0
Seismic to Right 0 0 0 0 0
Seismic to Left 0 0 0 0 0
BASE PLATE AND ANCHOR BOLT INFORMATION
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL COLUMNS
INT. INT. INT. COLUMNS COLUMNS CORNER TYPICAL
Base Plate Width 8.00 0.00 0.00 0.00 8.00
Base Plate Length 14.00 0.00 0.00 0.00 14.00
Anchor Bolt Quantity 4 0 0 0 4
Anchor Bolt Diameter 0.75 0.00 0.00 0.00 0.75
BRACING REACTIONS
BRACING
(KIPS) CONDITION: NUM OF BRACED BAYS: 0
(NOTE: BRACING GLOBAL X LOADS ARE PERPENDICULAR TO FRAME GLOBAL X LOADS)
(NOTE: FOR WALLS WITH AN X BRACING CONDITION,BRACING GLOBAL Y LOADS ARE ADDITIVE TO FRAME GLOBAL Y
GLOBAL
LOADS)X : POSITIVE TO RIGHT ENDWALL INPLANE BRACING
LEFT COL. RIGHT COL.** LEFT COL. RIGHT COL.
Wind to Front 4 4 0 0
Wind to Back 0 (LATERAL) 0 0 0
Seismic to Front 3 3 0 0
Seismic to Back 0 0 0 0
GLOBAL Y : POSITIVE TO UPWARD ENDWALL INPLANE BRACING
LEFT COL. RIGHT COL. LEFT COL. RIGHT COL.
Wind to Front +/- 3 +/- 3 0 0
Wind to Back +/- 3 (VERTICAL) +/- 3 0 0
Seismic to Front +/- 2 +/- 2 0 0
Seismic to Back +/- 2 +/- 2 0 0
*(The Snow Reaction provided is the maximum of: Roof Snow, Unbalanced Snow, and User Override Snow.)
** The user must combine the lean to bracing reactions with supporting building bracing reactions.
Endwall bracing is not included in these reactions.
29 of 31
Building: Main
*** PRELIMINARY REACTIONS ONLY - DO NOT USE FOR FINAL CONSTRUCTION!!! ***
This page covers the following frame lines:
3
GLOBAL X : POSITIVE INTO BUILDING (KIPS) E
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL TYP INT
(LATERAL) INT. INT. INT. D COLUMNS COLUMNS CORNER COLUMNS
Dead F 0 0 0 0 0
Collateral Dead 0 0 0 0 0
Roof Live 0 0 0 0 0
Roof Snow* 0 0 0 0 0
Wind to Left 0 0 0 0 0
Wind to Right 0 0 0 0 0
Wind to Front 1 0 3 0 1
Wind to Back -1 0 -3 0 -1
Seismic to Back 0 0 0 0 0
Seismic to Front 0 0 0 0 0
GLOBAL Y : POSITIVE UPWARD (KIPS) E
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL TYP INT
(VERTICAL) INT. INT. INT. D COLUMNS COLUMNS CORNER COLUMNS
Dead F 1 0 2 0 1
Collateral Dead 1 0 2 0 1
Roof Live 3 0 6 0 3
Roof Snow* 4 0 7 0 4
Wind to Left -4 0 -7 0 -6
Wind to Right -5 0 -8 0 -4
Wind to Front -6 0 -10 0 -6
Wind to Back -6 0 -10 0 -6
Seismic to Back 0 0 0 0 0
Seismic to Front 0 0 0 0 0
GLOBAL Z : POSITIVE COUNTERCLOCKWISE (FT-KIPS)
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL TYP INT
INT. INT. INT. COLUMNS COLUMNS CORNER COLUMNS
Dead 0 0 0 0 0
Collateral Dead 0 0 0 0 0
Roof Live 0 0 0 0 0
Roof Snow* 0 0 0 0 0
Wind to Left
Wind to Right
Wind to Front
Wind to Back
0
0
0
0
0
0
0
0
REFERENCE ONLY
0
0
0
0
0
0
0
0
0
0
0
0
Seismic to Back 0 0 0 0 0
Seismic to Front 0 0 0 0 0
BASE PLATE AND ANCHOR BOLT INFORMATION
MAIN FRAME COLUMNS FSW 1ST TYP LAST BSW FSW WIND BSW WIND ENDWALL COLUMNS
INT. INT. INT. COLUMNS COLUMNS CORNER TYPICAL
Base Plate Width 8.00 0.00 10.00 0.00 8.00
Base Plate Length 14.00 0.00 15.00 0.00 14.00
Anchor Bolt Quantity 4 0 4 0 4
Anchor Bolt Diameter 0.75 0.00 0.75 0.00 0.75
BRACING REACTIONS
BRACING
(KIPS) CONDITION: NUM OF BRACED BAYS: 0
(NOTE: BRACING GLOBAL X LOADS ARE PERPENDICULAR TO FRAME GLOBAL X LOADS)
(NOTE: FOR WALLS WITH AN X BRACING CONDITION,BRACING GLOBAL Y LOADS ARE ADDITIVE TO FRAME GLOBAL Y
GLOBAL
LOADS)X : POSITIVE TO RIGHT ENDWALL INPLANE BRACING
LEFT COL. RIGHT COL.** LEFT COL. RIGHT COL.
Wind to Front 0 0 0 0
Wind to Back 0 0 0 0
Seismic to Front 0 (LATERAL) 0 0 0
Seismic to Back 0 0 0 0
GLOBAL Y : POSITIVE TO UPWARD ENDWALL INPLANE BRACING
LEFT COL. RIGHT COL. LEFT COL. RIGHT COL.
Wind to Front +/- 0 +/- 0 0 0
Wind to Back +/- 0 +/- 0 0 0
Seismic to Front +/- 0 (VERTICAL) +/- 0 0 0
Seismic to Back +/- 0 +/- 0 0 0
*(The Snow Reaction provided is the maximum of: Roof Snow, Unbalanced Snow, and User Override Snow.)
** The user must combine the lean to bracing reactions with supporting building bracing reactions.
Endwall bracing is not included in these reactions.
30 of 31
REFERENCE ONLY
Back
Side
Wall
Left
End
Wall Ridge
Right
End
Wall
Front
Side
Wall
31 of 31