Professional Documents
Culture Documents
pinoybix.org/2020/12/mcq-in-machine-design-part-5-me-board-exam.html
December 6, 2020
This is the Multiple Choice Questions Part 5 of the Series in Machine Design as one of the
Mechanical Engineering topic. In Preparation for the ME Board Exam make sure to expose
yourself and familiarize in each and every questions compiled here taken from various
sources including but not limited to past Board Exam Questions in Mechanical Engineering
field, Mechanical Engineering Books, Journals and other ME References. I assume you are
looking for a reviewer that will help you achieve your goal to become a License Mechanical
1/19
Engineer very soon. Yes, you are in the right place to make your dream come true. Make
sure to familiarize each and every questions to increase the chance of passing the
Mechanical Board Examination.
A. 30 to 45
2/19
B. 35 to 50
C. 25 to 30
D. 15 to 20
View Answer:
Answer: Option A
Explanation:
202. The lack of backlash in a spur gear design/operation may result to __________
A. overloading
B. jamming
C. overheating
D. all of these
View Answer:
Answer: Option D
Explanation:
203. The distance from a point on a screw thread to a corresponding point on the next
thread measure along the axis
A. flank
B. lead
C. crest
D. pitch
View Answer:
Answer: Option D
Explanation:
204. As recommended the center to center distance between sprockets should not be less
than ____ times the bigger sprocket
A. 2.216
B. 1 3/4
3/19
C. 1 1/2
D. 2.59
View Answer:
Answer: Option C
Explanation:
205. Machine shop instrument for checking the flatness of plane surfaces to 10ths of
thousandths of a centimeter
B. dial caliper
C. planimeter
D. micrometer
View Answer:
Answer: Option C
Explanation:
A. 88xx
B. 48xx
C. 40xx
D. 46xx
View Answer:
Answer: Option C
Explanation:
207. Determine the minimum mean diameter of a taper pin for use to fix a lever to
a shaft if it is transmit a max torque of 700 in-lbs. The shaft diameter is 2 inches and
the material allowable stress is 15000 psi. Use factor of safety of 2.
A. 7.0 mm
B. 7.2 mm
4/19
C. 5.2 mm
D. 6.2 mm
View Answer:
Answer: Option D
Explanation:
208. Recommended design practice for steel lineshafting to limit the linear deflection to
________ inch/foot of length (maximum)
A. 0.020
B. 0.010
C. 0.012
D. 0.15
View Answer:
Answer: Option B
Explanation:
209. A link has a load factor of 0.8 the surface factor of 0.8 ; the surface factor is
0.92 and the endurance strength is 28000 psi. Compute the alternating stress of the
link if it is subjected to a reversing load. Assume a factor of safety of 3.
A. 8150
B. 10920
C. 9,333
D. 7260
View Answer:
Answer: Option C
Explanation:
210. Big chain sprocket wheels are designed with spokes/arms are generally elliptical
in cross section with major axis _______ times
5/19
A. 2
B. 2 ½
C. 1 ½
D. 3
View Answer:
Answer: Option A
Explanation:
211. For acceptable ideal range of tightness which may result from the application of specific
combination of allowances and tolerances.
A. allowance limit
B. tolerance limit
C. interference
D. Fit
View Answer:
Answer: Option D
Explanation:
212. Determine the safe wall thickness of a 30 inches steel tank with internal
pressure of 7.82 MPa. The yield stress of material is at 275.48 MPa. The factor of
safety to use is 2.0.
A. ¾ inch
B. 232.6 cm
C. 21.6 mm
D. 5/8 inch
View Answer:
Answer: Option C
Explanation:
6/19
213. The recommended center distance of sprockets should not be less than _________
times the diameter of bigger sprocket
A. 1.75
B. 2
C. 1 ½
D. 2 ¼
View Answer:
Answer: Option C
Explanation:
214. An occupant moves toward the center of a merry go around at 6 meters/sec. If the
merry go round rotates at 6 rev./min. Compute the acceleration component of the occupant
normal to the radius
A. 6.79
B. 8.29
C. 7.54
D. 6.11
View Answer:
Answer: Option C
Explanation:
215. The absolute viscosity of the fluid divided by its density expressed in same term of units
is also called _________
A. centistokes
B. kinematic viscosity
C. Petroffs equation
View Answer:
Answer: Option B
7/19
Explanation:
216. Find the tooth thickness on the tooth circle of a 20 degree full depth in volute
tooth having a diametral pitch of 3, circular pitch of 1.0472 and whole depth of tooth at
0.60.
A. 10.7 mm
B. 13.2 mm
C. 10.1 mm
D. 7.9 mm
View Answer:
Answer: Option B
Explanation:
217. It is required that pipes bigger than ________ mm. should not be screwed but flanged
A. 76.2
B. 63.5
C. 2 ¼ inch
D. 68.5
View Answer:
Answer: Option B
Explanation:
218. An eyebolt is lifting a block weighing 350 lbs. The eyebolt is of SAE C 1040
material with Su = 67 ksi and S2 = 55 ksi what is the stress area (in inches square) of the
bolt if it is under the unified coarse series thread?
A. 1341
B. 0.1134
C. 0991
D. 1043
View Answer:
8/19
Answer: Option B
Explanation:
219. Formed by the intersection of the adjacent flanks of adjacent threads when
extended is called.
A. crest apex
B. all of these
C. sharp root
D. sharp crest
View Answer:
Answer: Option C
Explanation:
220. In designing the spoke or wheel arm of a flywheel it is ideal to consider that
the cross-sectional area of the spoke at rim side should not be less than ________of
the cross area at the hub side
A. 80%
B. 2/3
C. 90%
D. 3/8
View Answer:
Answer: Option B
Explanation:
221. Find the number of active coils of a No. 8 wire Helical Spring with index of 6, steady
load with spring rate of 42.5 lb/in . Maximum allowable stress is 60 ksi
A. 25
B. 28
C. 29
D. 22
9/19
View Answer:
Answer: Option A
Explanation:
222. The cutting up to 70% is best for drilling extremely hard metals and for soft
materials ______degrees may be applied
A. 60
B. 45
C. 40
D. 48
View Answer:
Answer: Option C
Explanation:
223. _________is the process necessary to reduce the brittleness in alloy steel
A. martempering
B. carburizing
C. normalizing
D. tempering
View Answer:
Answer: Option D
Explanation:
224. The total machinery weight plus the foundation weight should be well distributed in the
corresponding soil area which is enough to cause a bearing stress within the safe bearing
capacity of the soil with a factor of safety of _________.
A. 4.5
B. 3
C. 4.2
D. 5.0
10/19
View Answer:
Answer: Option D
Explanation:
A. 1838 lbs.
B. 1698 lbs.
C. 3676 lbs.
D. 1848 lbs.
View Answer:
Answer: Option A
Explanation:
226. Steel springs are made of high carbon steel heat treated and/or cold worked to a
high elastic limit to get good elastic deflection. In general the carbon content is at
_________.
A. 0.40% or more
B. 0.65% or more
C. 0.5% or more
D. 0.66% or more
View Answer:
Answer: Option C
Explanation:
227. In a chain drive design for large speed reduction it is preferable to use a double
reduction or compound type of transmission instead of single two sprockets transmission.
Drives should type be so designed that the angle between two tight chain strand
does not exceed _____ degrees.
A. 45
B. 60
C. 55
11/19
D.90
View Answer:
Answer: Option A
Explanation:
228. Method of finishing/shaping a machine part of exceptionally high carbon or high
chromium steel parts (orveryhard material)
View Answer:
Answer: Option B
Explanation:
229. Alloy steel used in manufacturing bolts studs tubings subjected to torsional stresses
A. AISI 3141
B. AISI 2330
C. AISI4830
D. AISI 4310
View Answer:
Answer: Option B
Explanation:
A. Teflon
B. plastic
C. metal
D. all of these
12/19
View Answer:
Answer: Option C
Explanation:
231. A resulting force that replace two or more forces acting together
A. vector
B. couple
C. resultant
D. equilibrant
View Answer:
Answer: Option C
Explanation:
232. Stress relieving is also_________ for the purpose of reducing the internal stresses
of steel material/metal
A. tempering
B. normalizing
C. all of these
D. annealing
View Answer:
Answer: Option A
Explanation:
233. Matensite (stainless steel) contains 4 to 26% Cr. And a maximum of ______% nickel
A. 2.5
B. 3.25
C. 3.5
D. 2.0
View Answer:
Answer: Option A
13/19
Explanation:
234. Compute the deflection of a 18 coils helical soring having a load of 100 kgs. The
modulus of elasticity in shear of spring is 96.62 GPa, OD of 9 256 cm and with diameter
of 9 525 mm. The spring is square and ground ends.
A. 9 mm
B. 101 mm
C. 112 mm
D. 14 mm
View Answer:
Answer: Option B
Explanation:
235. A flanged bolt coupling has ten (10) steel 25.4 mm diameter bolts evenly tighten around
a 415 mm bolt circle. Determine the torque capacity of the connection if the allowable
shearing stress in the bolt is 50 MN/m2
A. 59.95 KN-m
B. 52.6 KN-m
C. 46.15 KN-m
D. 43.8 KN-m
View Answer:
Answer: Option B
Explanation:
236. The material that can cut/wear hardest substance subjected to:
A. carbide
B. abrasive
C. tungsten
D. vanadium
View Answer:
14/19
Answer: Option B
Explanation:
237. A ridge of uniform section in the form of a helix cut around the circumference of
a cylinder and advancing along the axis
A. thread roots
B. helix thread
C. screw threads
D. chamfers
View Answer:
Answer: Option C
Explanation:
238. Cast iron flywheels are commonly designed with factor of safety of
A. 10 to 13
B. 10 to 12
C. 10 to 14
D. 8 to 13
View Answer:
Answer: Option A
Explanation:
239. Class of material exhibiting decreased electrical conductivity with increasing
temperature
A. aluminum
B. p-type semiconductors
C. metals
D. n-type semiconductors
View Answer:
Answer: Option C
15/19
Explanation:
240. The welding made along the edges of two parallel plates is called ______
A. groove joint
B. fillet joint
C. edge joint
D. corner joint
View Answer:
Answer: Option C
Explanation:
241. Not part and in fact should not be used in the steel melting process
A. coke
B. silicon
C. zinc
D. aluminum
View Answer:
Answer: Option A
Explanation:
242. Rule of thumb in calculating the Equipment foundation mass should be ____ times
the weight of the machinery it is supposed to support
A. 3-5
B. 3-6
C. 3-9
D. 2-4
View Answer:
Answer: Option A
Explanation:
16/19
243. The strength of non-ferrous alloys is at maximum at room temperature while that
of ferrous metal has a maximum strength at_______ °F
A. 400
B. 1200
C. 450
D. 350
View Answer:
Answer: Option A
Explanation:
244. A 76.2 mm diameter shafting of SAE 1040 grade cold rolled, having a yield
point of 50 ksi and with a ¾ x ¾ x 5 inches key. Compute the minimum yield point
in the key in order to transmit the torque of the shaft. The factor of safety to used
is 2 and Sys = 0.5Sy.
A. 39.120 Ksi
B. 42.130 Ksi
C. 279.20 Ksi
D. 47.120 Ksi
View Answer:
Answer: Option D
Explanation:
245. The ratio of stress acting on an elastic substance to the decrease in volume per unit
volume
A. bulk modulus
B. modules of resilience
C. elastic limit
D. modules of elasticity
View Answer:
Answer: Option A
17/19
Explanation:
246. The normal helix angles in helical gear is recommended in the range of
______degrees.
A. less than 18
B. 20 to 35
C. 15 to 25
D. 20 to 30
View Answer:
Answer: Option C
Explanation:
247. Type of bolt commonly used in the construction that is threaded in both ends
A. stud bolt
C. hex bolt
View Answer:
Answer: Option A
Explanation:
248. It is rigid piece which serves to transmit force from a piece another piece or to
cause/ control motion
A. follower
B. crank
C. cam motion
D. link
View Answer:
Answer: Option D
Explanation:
18/19
249. A 20 kgs. cast iron piece rest on a plain horizontal aluminum surface. To move
the object it needs a force of 7 lbs. The density of AI is 0.098 lb/in3 and iron is 0.260 lb/in3
A. 0.172
B. 0.186
C. 1.601
D. 0.160
View Answer:
Answer: Option D
Explanation:
A. Mn Hadfield steel
B. chrome-moly steel
C. stainless steel C
View Answer:
Answer: Option C
Explanation:
Subscribe
Prev Article Next Article
19/19