Professional Documents
Culture Documents
Báo Cáo Quá Trình Quá Độ Điện Từ
Báo Cáo Quá Trình Quá Độ Điện Từ
KHOA ĐIỆN_ĐIỆN TỬ
NHÓM 11
LỚP: 20040102
The differences in the two standards require two first Sự khác biệt trong hai tiêu chuẩn yêu cầu hai phép tính
cycle calculations and an interrupting calculation. The chu kỳ đầu tiên và một tính toán gián đoạn. Biểu diễn lý
ideal representation for multivoltage systems is the tưởng cho các hệ thống đa điện áp là đơn giản nhất điều
simplest that determines with reasonable conservatism đó xác định với sự bảo thủ hợp lý ảnh hưởng của cả
the influences of both low- and high-voltage induction điện áp thấp và cao động cơ cảm ứng làm nhiệm vụ
motors on short-circuit duties for circuit breakers and ngắn mạch cho bộ ngắt mạch và cầu chì ở cả mức thấp
fuses at both low and high voltages. A simple first cycle và cao điện áp. Một mạng chu kỳ đầu tiên đơn giản kết
network combining the two similar but different hợp hai mạng tương tự nhưng khác nhau của IEEE Std
networks of IEEE Std C37.13-1990 [B5] and IEEE Std C37.13-1990 [B5] và IEEE Std C37.010-1999 [B4] phù
C37.010-1999 [B4] fits this ideal. The following hợp với lý tưởng này. Các theo cách giải thích và định
interpretation and redefinition, based on extending nghĩa lại, dựa trên việc mở rộng các điểm tương đồng
existing similarities, resolves the differences and obtains hiện có, giải quyết sự khác biệt và thu được một mạng
a single network. Table 6-1 and Table 6-2 provide the duy nhất. Bảng 6-1 và Bảng 6-2 cung cấp hệ số nhân và
multiplying factors and suggested motor reactances to phản ứng động cơ được đề xuất sẽ được sử dụng khi dữ
be used when actual data is not available. liệu thực tế không có sẵn.
For a typical induction motor, the subtransient reactance Đối với một động cơ cảm ứng điển hình, điện trở truyền
of 16.7% is determined by the initial magnitude of dẫn phụ 16,7% được xác định bởi cường độ ban đầu của
symmetrical root-mean-square (rms) current contributed dòng điện gốc-trung bình-bình phương đối xứng (rms)
to a terminal short circuit, assumed to be six times rated. đóng góp vào một thiết bị đầu cuối ngắn mạch, giả định
Using a “4.8 times rated current” first cycle estimate for là sáu lần danh định. Sử dụng chu kỳ đầu tiên "4,8 lần
larger size low-voltage induction motors, described as dòng định mức" ước tính cho động cơ cảm ứng điện áp
“medium 50 hp, etc.” in Table 6-1 and Table 6-2, is thấp kích thước lớn hơn, được mô tả là "trung bình 50
effectively the same as multiplying the subtransient mã lực, v.v." trong Bảng 6-1 và Bảng 6-2, có hiệu quả
reactance by approximately 1.2 (6.0/4.8 = 1.25). For this giống như việc nhân hệ số phụ điện kháng xấp xỉ 1,2
motor group, there is reasonable correspondence of low- (6,0 / 4,8 = 1,25). Đối với nhóm động cơ này, có sự
and medium-voltage calculation procedures. tương ứng của các quy trình tính toán hạ áp và trung áp.
For smaller induction motors, “small < 50 hp” in Table Đối với động cơ cảm ứng nhỏ hơn, "nhỏ <50 mã lực"
6-1 and Table 6-2, a conservative estimate is the “3.6 trong Bảng 6-1 và Bảng 6-2, một ước tính là "3,6 lần
times rated current” (equivalent of 0.28 per-unit dòng định mức" (tương đương với 0,28 trên một đơn vị
reactance) first cycle assumption of low-voltage điện kháng) chu kỳ đầu tiên giả định các tiêu chuẩn điện
standards, and this is effectively the same as multiplying áp thấp và điều này cũng giống như việc nhân 16,7%
16.7% subtransient reactance by 1.67. phản ứng truyền dẫn phụ bằng 1,67.
With this interpretation as a basis, the recommended Với cách giải thích này là cơ sở, động cơ cảm ứng điện
“small” low-voltage induction motor representation is áp thấp "nhỏ" được khuyến nghị biểu diễn được thể hiện
shown by Table 6-2, column 4, and by a dotted line on bằng Bảng 6-2, cột 4, và bằng một đường chấm trên
Figure 6-3. The entries for medium-size motors are the Hình 6-3. Các các mục nhập đối với động cơ cỡ trung
same as in Table 6-1 for medium-voltage calculations, bình giống như trong Bảng 6-1 đối với động cơ trung áp
and their use adds conservatism to low-voltage các phép tính và việc sử dụng chúng bổ sung tính bảo
calculations, and their use adds some conservatism to thủ cho các phép tính điện áp thấp khi nhiều động cơ
low-voltage calculations when many induction motors cảm ứng không phải là "nhỏ". Các mục nhập cho động
are not “small.” The entries for small-size motors are cơ kích thước nhỏ về cơ bản là giống như trong IEEE
essentially the same as in IEEE Std C37.13 [B5] for Std C37.13 [B5] ] để tính toán điện áp thấp và việc sử
low-voltage calculations, and their use adds some dụng chúng bổ sung một số bảo thủ để tính toán chu kỳ
conservatism to medium-voltage first cycle calculations đầu tiên trung áp mà không thay đổi gián đoạn tính toán
without changing interruptingduty calculations. Column nhiệm vụ. Cột 4 của Bảng 6-1 cung cấp các hệ số điện
4 of Table 6-1 provides the recommended reactance trở được khuyến nghị cầu nối hai tiêu chuẩn được ANSI
multipliers that bridge the two ANSI-approved phê duyệt.
standards. Nhiều động cơ hiệu suất cao hơn đang được sử dụng
More high-efficiency motors are being used in industrial trong hệ thống công nghiệp, có dòng điện rôto bị khóa
system, which have higher locked-rotor currents and và do đó điện kháng truyền tải phụ thấp hơn. Một số kỹ
therefore lower subtransient reactances. Some thuật phán đoán phải được sử dụng trong việc lựa chọn
engineering judgment must be used in the selection of các điện trở động cơ giả định dựa trên các loại động cơ
đang được sử dụng.
assumed motor reactances based on the types of Bảng 6-1 — Hệ số nhân điện trở động cơ cảm ứng từ
motors being used.
Bảng 6-2 — Các điện trở động cơ cảm ứng được đề xuất từ
IEEE Std C37.010 [B4] và IEEE Std C37.13 [B5]
6.10 One-line diagram data
Dòng sự cố đối xứng qua Trans T-13 được thể hiện trong Bảng
6-4.
Bảng 6-3 — Các phép tính R và X trên mỗi đơn vị cho chu kỳ
đầu tiên và làm gián đoạn thời gian
Bảng 6-3 — Các phép tính R và X trên mỗi đơn vị cho chu kỳ đầu
tiên và gián đoạn thời gian (tiếp theo)
Bảng 6-4 — Các tính toán cho dòng điện sự cố qua trans T-13
Hình 6-4 — Sơ đồ một dòng tương đương và trở kháng cho tính CONTRIBUTIONS TO FAULT:
toán mẫu
BUS to BUS MAG ANG BUS to BUS MAG ANG
Sample calculation #2
13.22
Z commonbase=5.75 2
=5.261%
13.8
Z Common base
Z commonbase=Z equip .
Zequip base
10 X
Z10=0.05261 =0.02175098+ j0.21756 at =10.0
2.5 R
Máy biến áp T13 được thay đổi và có định mức 2,5 MVA, 13,2 /
2,3 kV, trở kháng 5,75%, và vòi vận hành đã chọn là 13,53 kV.
Vì đánh giá điện áp máy biến áp không phù hợp với điện áp cơ
bản 13,8 kV, ba mục nên được thay đổi, một là điện áp cơ bản,
thứ hai là trở kháng máy biến áp và thứ ba là trở kháng động cơ
mới điện áp cơ sở của hệ thống. Để điều chỉnh trở kháng với cơ
sở điện áp 13,8 kV sơ cấp, Phương trình (3.11) và Phương trình
(3.12) được sử dụng.
2
kV Equip base
Z commonbase=Z equip . 2
kV Common base
2
13.2
Z commonbase=5.75 2
=5.261%
13.8
6.12 Sample computer printout
Z Common base
Z commonbase=Z equip . The computer printout following is for selected buses to show the
Zequip base more critical buses and to show the effects the induction motors
on the fault levels. The input listing can be found in Chapter 4.
10 X Because of the decaying ac sources, the first cycle and
Z10=0.05261 =0.02175098+ j0.21756 at =10.0
2.5 R interrupting time fault currents will differ.
This value can be entered into some computer programs with the Giá trị này có thể được nhập vào một số chương trình máy tính
13.53 kV tap and the transformer impedance will be corrected for với vòi 13,53 kV và trở kháng của máy biến áp sẽ được hiệu
tap position. However, for hand calculations or computer chỉnh cho vị trí của vòi. Tuy nhiên, để tính toán tay hoặc các
programs without transformer tap capabilities, a second step is chương trình máy tính không có khả năng chạm biến áp, cần thực
required to correct for the transformer tap position. The same hiện bước thứ hai để đúng vị trí vòi máy biến áp. Phương trình
equation as shown above can be used and the change in tương tự như được hiển thị ở trên có thể được sử dụng và sự thay
transformer calculated in one step. Two steps are shown here for đổi máy biến áp được tính toán trong một bước. Hai bước được
clarity.The transformer T-13 impedance on the 10 MVA system hiển thị ở đây để rõ ràng. Trở kháng T-13 của máy biến áp trên
base is: cơ sở hệ thống 10 MVA là:
13.532 13.53
2
Z commonbase=0.02175098+ j 0.021756 =0.022+ j0.21999
Z commonbase =0.02175098+ j 0.021756 =0.022+ j0.21999
13.22 13.2
2
The secondary system base voltage is 2.3 × 13.53/13.2 = 2.3575. Điện áp cơ bản của hệ thống thứ cấp là 2,3 × 13,53 / 13,2 =
2,3575.
The 2.4 kV rated motor is corrected to the system base voltage
by the same equation as used for the transformer. Động cơ định mức 2,4 kV được hiệu chỉnh về điện áp cơ sở của
hệ thống theo phương trình tương tự như dùng cho máy biến áp.
( )
2
2.4
Z commonbase=(0.02744+ j 0.818)
( )
2
2.35752 2.4
Z commonbase=(0.02744+ j 0.818) 2
2.3575
(shown with first cycle impedance)
(hiển thị với trở kháng chu kỳ đầu tiên)
= (0.02844 + j 0.84776) for first cycle
¿ ( 0.02844+ j 0.84776 ) cho chu kỳ đầu * BUS: 04:MILL-2 *****
Dòng sự cố đối xứng qua Trans T-13 được thể hiện trong Bảng 6-6. SYM kA*1.6 = 12.31 ASYM kA Based on X/R ratio = 11.60 kA
Bảng 6-5 — Các tính toán R và X trên mỗi đơn vị cho chu kỳ đầu tiên và MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY =
thời gian ngắt 7.69 SYM, = 11.60 ASY
CONTRIBUTIONS TO FAULT:
Bản in máy tính sau đây dành cho các xe buýt được chọn để hiển SYM kA*1.6 = 12.10 ASYM kA Based on X/R ratio = 11.10 kA
thị các xe buýt quan trọng hơn và để hiển thị ảnh hưởng của động
cơ cảm ứng đối với mức độ lỗi. Danh sách đầu vào có thể được MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY =
tìm thấy trong Chương 4. Do các nguồn xoay chiều đang phân 7.56 SYM, = 11.10 ASY
hủy, chu kỳ đầu tiên và lỗi thời gian gián đoạn dòng điện sẽ khác MAX. HIGH VOLTAGE DISTRIBUTION FUSE DUTY = 7.69
nhau. SYM, = 11.29 ASY
First Cycle* Chu kỳ đầu tiên
BUS: 100 :UTIL-69 ***** BUS: 100 :UTIL-69 *****
8.914 KA AT -87.27 DEG (1065.29 MVA) : X/R = 21.65 KV = 8.914 KA AT -87.27 DEG (1065.29 MVA) : X/R = 21.65 KV =
69.000 69.000
Ze = 0.0004472 +j 0.0093764 (Complex) Ze = 0.0004472 +j 0.0093764 (Complex)
SYM kA*1.6 = 14.26 ASYM kA Based on X/R ratio = 14.11 kA SYM kA*1.6 = 14.26 ASYM kA Based on X/R ratio = 14.11 kA
MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY = MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY =
9.25 SYM, = 14.64 ASY 9.25 SYM, = 14.64 ASY
MAX. HIGH VOLTAGE DISTRIBUTION FUSE DUTY = 9.77 MAX. HIGH VOLTAGE DISTRIBUTION FUSE DUTY = 9.77
SYM, = 15.46 ASY SYM, = 15.46 ASY
CONTRIBUTIONS TO FAULT: CONTRIBUTIONS TO FAULT:
BUS to BUS MAG ANG BUS to BUS MAG ANG BUS to BUS MAG ANG BUS to BUS MAG ANG
UTIL 100 :UTIL 8.367 -87.42 01:69-1 100 :UTIL 0.318 -84.53 UTIL 100 :UTIL 8.367 -87.42 01:69-1 100 :UTIL 0.318 -84.53
02:69-2 100 :UTIL 0.229 -85.54 02:69-2 100 :UTIL 0.229 -85.54
* BUS: 04:MILL-2 ***** CONTRIBUTIONS TO FAULT:
7.691 KA AT -85.66 DEG ( 183.83 MVA): X/R = 13.61 KV = BUS to BUS MAG ANG BUS to BUS MAG ANG
13.800
31:FDR P 36:T13 SE -0.399 -87.25 24:FDR M 31:FDR P 7.076 -
Ze = 0.0041165 +j 0.0542433 (Complex) 83.84
SYM kA*1.6 = 12.31 ASYM kA Based on X/R ratio = 11.60 kA * BUS: 36:T13 SEC *****
MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY = 11.254 KA AT -85.21 DEG ( 46.78 MVA) : X/R = 15.06 KV =
7.69 SYM, = 11.60 ASY 2.400
MAX. HIGH VOLTAGE DISTRIBUTION FUSE DUTY = 8.03 Ze = 0.0178490 +j 0.2130016 (Complex)
SYM, = 12.11 ASY
SYM kA*1.6 = 18.01 ASYM kA Based on X/R ratio = 17.18 kA
CONTRIBUTIONS TO FAULT:
MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY =
BUS to BUS MAG ANG BUS to BUS MAG ANG 11.26 SYM, = 17.18 ASY
02:69-2 04:MILL-2 6.338 -85.68 04:MILL-2 15:FDR I -0.550 - MAX. HIGH VOLTAGE DISTRIBUTION FUSE DUTY =
86.35 11.90 SYM, = 18.16 ASY
04: MILL-2 27:T12 PR -0.167 -82.49 04: MILL-2 16:T9 PRI - CONTRIBUTIONS TO FAULT:
0.091 -84.11
BUS to BUS MAG ANG BUS to BUS MAG ANG
04: MILL-2 08: FDR L 0.000 0.00 04:MILL-2 24:FDR M -0.545
-85.95 Med Ind 36:T13 SE 2.939 -88.08 31:FDR P 36:T13 SE 8.320
MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY = Ze = 0.0004440 +j 0.0096591 (Complex)
7.56 SYM, = 11.10 ASY CONTRIBUTIONS TO FAULT:
MAX. HIGH VOLTAGE DISTRIBUTION FUSE DUTY = 7.69 BUS to BUS MAG ANG BUS to BUS MAG ANG
SYM, = 11.29 ASY
CONTRIBUTIONS TO FAULT:
CONTRIBUTIONS TO FAULT:
BUS to BUS MAG ANG BUS to BUS MAG ANG
BUS to BUS MAG ANG BUS to BUS MAG ANG
04: MILL-2 24:FDR M 7.016 -84.58 24:FDR M 31:FDER P
04: MILL-2 24:FDR M 7.016 -84.58 24:FDR M 31:FDER P
-0.399 -87.20
-0.399 -87.20
24:FDR M 32:FDR Q -0.148 -82.86
24:FDR M 32:FDR Q -0.148 -82.86
* BUS: 31:FDR P *****
* BUS: 31:FDR P *****
7.474 KA AT -84.02 DEG ( 178.65 MVA): X/R = 10.02 KV =
7.474 KA AT -84.02 DEG ( 178.65 MVA): X/R = 10.02 KV = 13.800
13.800
Ze = 0.0058284 +j 0.0556708 (Complex)
Ze = 0.0058284 +j 0.0556708 (Complex)
SYM kA*1.6 = 11.96 ASYM kA Based on X/R ratio = 10.80 kA
SYM kA*1.6 = 11.96 ASYM kA Based on X/R ratio = 10.80 kA
MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY =
MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY = 7.47 SYM, = 10.80 ASY
7.47 SYM, = 10.80 ASY
MAX. HIGH VOLTAGE DISTRIBUTION FUSE DUTY = 7.48
MAX. HIGH VOLTAGE DISTRIBUTION FUSE DUTY = 7.48 SYM, = 10.80 ASY
SYM, = 10.80 ASY
CONTRIBUTIONS TO FAULT: CONTRIBUTIONS TO FAULT:
BUS to BUS MAG ANG BUS to BUS MAG ANG BUS to BUS MAG ANG BUS to BUS MAG ANG
31:FDR P 36:T13 SE -0.399 -87.25 24:FDR M 31:FDR P 7.076 - 02:69-2 04:MILL-2 6.321 -85.69 04:MILL-2 15:FDR I -0.393 -
83.84 86.48
* BUS: 36:T13 SEC ***** 04:MILL-2 27:T12 PR -0.031 -85.11 04:MILL-2 16:T9 PRI
0.000 0.00
11.254 KA AT -85.21 DEG ( 46.78 MVA) : X/R = 15.06 KV =
2.400 04:MILL-2 08:FDR L 0.000 0.00 04:MILL-2 24:FDR M -0.236 -
86.99
Ze = 0.0178490 +j 0.2130016 (Complex)
* BUS: 24:FDR M *****
SYM kA*1.6 = 18.01 ASYM kA Based on X/R ratio = 17.18 kA
6.866 KA AT -84.81 DEG ( 164.12 MVA) : X/R = 11.28 KV =
MAX. HIGH VOLTAGE CLF AND POWER FUSE DUTY = 13.800
11.26 SYM, = 17.18 ASY
Ze = 0.0055071 +j 0.0606812 (Complex)
MAX. HIGH VOLTAGE DISTRIBUTION FUSE DUTY =
11.90 SYM, = 18.16 ASY CONTRIBUTIONS TO FAULT:
CONTRIBUTIONS TO FAULT: BUS to BUS MAG ANG BUS to BUS MAG ANG
BUS to BUS MAG ANG BUS to BUS MAG ANG 04:MILL-2 24:FDR M 6.630 -84.74 24:FDR M 31:FDR P -0.184
-87.68
Med Ind 36:T13 SE 2.939 -88.08 31:FDR P 36:T13 SE 8.320
24:FDR M 32:FDR Q -0.052 -84.81
-84.20
* BUS: 31:FDR P *****
Làm gián đoạn thời gian
6.790 KA AT -84.18 DEG ( 162.29 MVA) : X/R = 10.10 KV =
* BUS: 100 :UTIL-69 ***** 13.800
8.654 KA AT -87.37 DEG (1034.21 MVA) : X/R = 21.99 KV = Ze = 0.0062527 +j 0.0612986 (Complex)
69.000
CONTRIBUTIONS TO FAULT:
Ze = 0.0004440 +j 0.0096591 (Complex)
BUS to BUS MAG ANG BUS to BUS MAG ANG
CONTRIBUTIONS TO FAULT:
31:FDR P 36:T13 SE -0.184 -87.70 24:FDR M 31:FDR P 6.606 -
BUS to BUS MAG ANG BUS to BUS MAG ANG 84.08
UTIL 100 :UTIL 8.367 -87.42 01:69-1 100 :UTIL 0.165 -85.33 UTIL 100 :UTIL 8.367 -87.42 01:69-1 100 :UTIL 0.165 -85.33
02:69-2 100 :UTIL 0.121 -86.50 02:69-2 100 :UTIL 0.121 -86.50
* BUS: 01:69-1 ***** * BUS: 01:69-1 *****
6.633 KA AT -81.93 DEG ( 792.74 MVA) : X/R = 7.19 KV = 6.633 KA AT -81.93 DEG ( 792.74 MVA) : X/R = 7.19 KV =
69.000 69.000
Ze = 0.0017702 +j 0.0124897 (Complex) Ze = 0.0017702 +j 0.0124897 (Complex)
CONTRIBUTIONS TO FAULT: CONTRIBUTIONS TO FAULT:
BUS to BUS MAG ANG BUS to BUS MAG ANG BUS to BUS MAG ANG BUS to BUS MAG ANG
01:69-1 03:MILL-1 -0.166 -85.46 01:69-1 100 :UTIL -6.467 - 01:69-1 03:MILL-1 -0.166 -85.46 01:69-1 100 :UTIL -6.467 -
81.84 81.84
* BUS: 04:MILL-2 ***** * BUS: 04:MILL-2 *****
6.981 KA AT -85.78 DEG ( 166.87 MVA) : X/R = 13.78 KV = 6.981 KA AT -85.78 DEG ( 166.87 MVA) : X/R = 13.78 KV =
13.800 13.800
Ze = 0.0044095 +j 0.0597656 (Complex) Ze = 0.0044095 +j 0.0597656 (Complex)
CONTRIBUTIONS TO FAULT:
[B3] IEC 909-1988, International Standard, Short-circuit Current
BUS to BUS MAG ANG BUS to BUS MAG ANG Calculation in Threephase a.c. Systems, First edition.
02:69-2 04:MILL-2 6.321 -85.69 04:MILL-2 15:FDR I -0.393 -
86.48 [B4] IEEE Std C37.010-1999 (Reaff 2005), IEEE Application
04:MILL-2 27:T12 PR -0.031 -85.11 04:MILL-2 16:T9 PRI Guide for AC HighVoltage Circuit Breakers Rated on a
0.000 0.00 Symmetrical Current Basis.
6.866 KA AT -84.81 DEG ( 164.12 MVA) : X/R = 11.28 KV = [B6] IEEE Std C37.41-2000, IEEE Standard Design Tests for
13.800 Distribution Cutouts and Fuse Links, Secondary Fuses,
Distribution Enclosed Single-Pole Air Switches, Power Fuses,
Ze = 0.0055071 +j 0.0606812 (Complex)
Fuse Disconnecting Switches, and Accessories.
CONTRIBUTIONS TO FAULT:
CONTRIBUTIONS TO FAULT:
Then left click on the workspace, the program will display the following dialog box:
therein:
“Bus number” and “bus name” is the place to enter the number and name of the busbar..
The show area permits the bus to be placed horizontally (horizontal bar), placed vertically (vertical bar), set
Associate in Nursing oval (oval), or parallelogram (rectangle). The “pixel thickness” and “display size” indicators
are the thickness and display size of the busbar. “Area and zone” enter the serial variety and name of the
world and area if the network is large. “Nominal voltage” is that the rated voltage of the busbar, “voltage” and
“angle” are the voltage (v) and therefore the voltage point (degrees) placed at the busbar.
“System slack bus” choose if we would like that bus to be the “slack bus” of the system. every system should
have a “slack bus”, and also the bus hand-picked must be the one connected to the transmitter.
Once done, click OK
down.
Voltage control: enter the generator letter worths (Mvar output), the minimum value (Min Mvar) and also the most
value (Max Mvar) of the generator Q. “Available for AVR” mechanically adjusts the generator terminal voltage,
“setpoint voltage” is that the generator terminal voltage.
“Input/Output Curve”
Select “cubic cost model” to define the generator cost curve as: C(Pgi) = (d*Pgi^3 + c*Pgi^2 + b*Pgi + a) * (fuel cost),
choose “ piecewise linear” to define a linearized cost curve.
“Fule cots” fuel price, “Number of break points” is the number of points where we want to approximate the curve to
straight lines.
“Fault Parameters”
“Generator MVA Base” is the base power (S) of the generator. “Positive Sequence Internal Impedace":
impedance of positive order
“Negative Sequence Internal Impedace”: reverse order total impedance “Zero Sequence Internal
Impedace”: total impedance zero.
“Neutral-to-Ground Impedance": total resistance to ground.
“Generator Step Transfomer”: model transformer impedance (default is none).
Transformers
On the Edit Toolbar select the icon of the transformer.
Then using the mouse to click on the two busbars that the generator connects to (like drawing a line), we get the
following dialog box:
After getting into the names and serial numbers of the 2 buses that the electrical device connects to (usually the
program can try this automatically), we tend to fill within the values of the impedances R, L, C (or B) in the
corresponding boxes. response: “Resistance”, “Reactance”, “Charging”.
“Limit A”, “Limit B”, “Limit C” are the power limits of the transformer, the program allows to use 3 different limit
values.
If you click Error Parameters, a dialog box like the one above will appear. Enter the zero ordinal impedance values in the
R, X, C boxes (usually the program will automatically fill in these values when we enter the ordinal impedance).
"Settings" to select the connection type of transformer windings After setting the parameters, click OK, the results are
as follows:
2.3 Lines
On the Edit Toolbar, select the line icon.
Having selected the same transformer, we also draw the line between the two power rails just like drawing a line in
Paint. After drawing, we also get a dialog like the following
Completely similar to the transformer, we also fill in the rated voltage parameters
2.4 LOAD.
On the Edit Toolbar select the download icon, as shown below:
Then click near the bus that we want to place the load, we get the following dialog box:
Similar to other components, after setting the screen properties (size, direction of rotation...), we need to enter the
power consumption values "MW value": active power and "Mvar value": reactive power consumed). Then click OK..
Similar to the load, we also click on the busbar to compensate, we get the following dialog box:
As with other devices, we also configure display parameters. Next set the nominal compensation value (Mvar nominal).
Select the Fixed control modes: Automatic, Discrete, and Continuous are the modes that set the maximum and
minimum allowable voltage values compared to the desired value,and divide it into small steps when compensate.
3 Operational problems.
Method 1: click thereon load, once the panel appears, we alter the worth "MW Value" or "Mvar Value" like the active
and reactive power, for example here the change is 200MW and a hundred Mvar, then OK.
Method 2: Right click on one of the two bids P and Q, we will get the following dialog box:
Change the worth "Delta per Mouse Click" (default is no), this value represents the increase or decrease of such AN
quantity for every click on the button to extend or decrease the load, maybe here select the value is 50, then for each
modification by mouse click, we are going to increase or decrease the active or reactive power by an amount of fifty
MW (or 50 Mvar). Then click OK, we will get the following result:
0.000 MW
199.953 MW 58.496 MVR
200.0 MW nam bon ba
7.471 MVR 1.050 pu
7.5 MVR
mot
1.050 pu
200 MW
1.050 pu
-2.823 Deg hai
100 MW
103 MVR
100 MVR
100 MW
Now we just need to click on the increase or decrease button of P or Q respectively. For example, to get the value P=
100MW and Q= 100 Mvar, we press to decrease P 2 times and increase Q 1 time. The results are as follows:
0.000 MW
100.020 MW 102.634 MVR
100.0 MW nam bon ba
1.493 MVR 1.050 pu
1.5 MVR
mot
1.050 pu
100 MW
1.050 pu
-1.411 Deg hai
100 MW
101 MVR
100 MVR
100 MW
Method 1: Click on the transmitter to be changed, select “Infomation Dialog…”, a dialog box similar to when we set the
parameters for the detector to be detected, then change the desired values.
Method 2: Click on the value of P transmitter or Q transmitter of the currently displayed transmitter. We get a dialog
box, and change the value "Delta Per Mouse Click".
For example, change the power of the transmitter in busbar "two", choose the value "Delta per Mouse Click" to be 50,
change P=150 MW and Q = 50Mvar, we get the following:
0.000 MW
50.000 MW 129.130 MVR
25.4 MVR
mot
1.050 pu
100 MW
1.030 pu
0.052 Deg hai
150 MW
50 MVR
100 MVR
100 MW
1.047 pu
1.050 pu
-1.459 Deg
-1.980 Deg
Returning to the previous example, all generators have a terminal voltage of 1.05 pu, now reduced to 1 pu for all
generators. When the dialog box appears, after modifying the first generator, click the save button and then click the
up button to configure the other generators.:
The results obtained are as follows:
0.000 MW
50.000 MW 129.407 MVR
50.0 MW nam bon ba
25.559 MVR 1.000 pu
25.6 MVR
mot
1.000 pu
100 MW
0.978 pu
0.059 Deg hai
150 MW
50 MVR
100 MVR
100 MW
Method 1: Right click on the element, select “Information.”, at status select “Open”, for example generator:
Method 2: Left-click on the cutter to connect that element to the system. Using the previous example, i.e. cut the
circuit breaker at busbar “two”:
0.000 MW
99.989 MW 102.561 MVR
100.0 MW nam bon ba
2.562 MVR 1.000 pu
2.6 MVR
mot
1.000 pu
100 MW
1.000 pu
-1.555 Deg hai
0 MW
0 MVR
0 MVR
0 MW
0.000 MW
100.000 MW 102.574 MVR
100.0 MW nam bon ba
2.573 MVR 1.000 pu
2.6 MVR
mot
1.000 pu
100 MW
1.000 pu
-1.556 Deg hai
0 MW
0 MVR
0 MVR
0 MW
We can select other busbars, then select short circuit types and then press the . button
“Calculate”, the example here selects busbar 5 and short circuit type 3 phase, the result is as follows:
The short current is shown within the “Fautl curent” box, with the amplitude price being “Magnitude” (pu), and
therefore the point being “Angle” (degrees). different values are shown in the table. Order:
To see the present once the contact runs on the lines, we have a tendency to minimize the short circuit dialog box, click
the arrow next to the “fault” button, choose the show mode, for example part A.
The results obtained are as follows:
17.597 pu
15.565 pu
15.6 pu nam bon ba
mot
0.311 pu
0.624 pu
0.951 deg hai
15 pu
TBA 1:
115
SrT 1=120 MVA ; U KT %=10,5 % ; KV
6,3
TBA 2:
115
SrT 2=80 MVA ;U KT % =10,5 % ; KV
10,5
TBA 3:
115
SrT 3 =120 MVA ; U KT %=10,5 % ; KV
35
TBA 4:
115
SrT 4=80 MVA ; U KT %=10,5 % ; KV
10,5
Đường Dây 1:
Ω
L1=132 km; U =115 KV ; X ' =0,4
km
Đường Dây 2:
Ω
L2=78 km ;U=115 KV ; X ' =0,4
km
Đường Dây 3:
' Ω
L3=123 km ; U=115 KV ; X =0,4
km
Đường Dây 4:
' Ω
L1=50 km ;U=35 KV ; X =0,4
km
U bs 2=115 KV
U bs 3=37 KV
U bs 4 =10,5 KV
Sbs
⇒ I bs 1= =9,2 KA
√3 U bs 1
I bs2 =0,5 KA
I bs3 =1,56 KA
I bs 4=5,5 KA
Máy Phát:
¿ } . {{S} rsub {bs}} over {{S} rsub {rG1}} = {100} over {25} .0,14=0,5 ¿
X rG1 =X d
¿ } . {{S} rsub {bs}} over {{S} rsub {rG2}} = {100} over {30} .0,13=0,4 ¿
X rG2 =X d
¿ } . {{S} rsub {bs}} over {{S} rsub {rG3}} = {100} over {30} .0,14=0,4 ¿
X rG3 =X d
¿ } . {{S} rsub {bs}} over {{S} rsub {rG4}} = {100} over {35} .0,13=0,¿
X rG 4=X d
¿ 10,5 100
X T 2= . 0,131
100 80
10,5 100
X ¿T 4 = . 0,087
100 120
¿ 10,5 100
X T 3= . 0,131
100 80
Đường dây
Sbs 100
X ¿D 1= X ' . l 1 . 2
=0,4.132. 2
=0,39
U1 115
¿ 100
X D 2=0,4.78. 2
=0,23
115
¿ 100
X D 3=0,4.123. =0,37
1152
100
X ¿D 4 =0,4.50 . 2
=1,63
35
X 7 =X 4+ X 1=0,09+ 0,367=0,457
X 8=X 3 + X 6=2,117+0,14=2,257
X7. X 8 0,457.2,257
X 9= + X5= + 0,08=0,46
X7+ X8 0,457+ 2,257
E∑ =1
0,46.0,362
X∑= =0,2
0,46 +0,362
(3) bs I
0.5
=>> Dòng ngắn mạch I N 1 = X = 0,2 =2,5
∑
X 8=X 5 + X 2=0,08+0,282=0,368
X7. X 8 0,457.0,368
X 9= + X6= + 0,146=0,34
X7+ X8 0,457 +0,368
E∑ =1
X 9 . X 3 0,2.2,117
X∑= =
X 9 + X 3 0,2+2,117
=0,3
( 3) 0,5
=>> I N 2 = 0,3 =1,667