Professional Documents
Culture Documents
& C…
Previous Screen
Welcome: p260jea
Product: ROTARY/TRACK DRILLS
Model: MD5150C ROTARY/TRACK DRILLS SEY00148
Configuration: MD5150C Track Drill (Cab, Undercarriage, Engine, Electrical)
SEY00001UP (MACHINE) POWERED BY C11 Engine
i06131974
Operator Controls
SMCS 7300; 7301; 7451
Note: Your machine may not be equipped with all of the controls that are described in this topic.
Operator Controls
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/siswe… 1/9
6/11/2016 MD5150C Track Drill (Cab, Undercarriage, Engine, Electrical) SEY00001UP (MACHINE) POWERED BY C11 Engine(SEBP7124 16) Systems & C…
Illustration 1 g03826507
Operator Cab
(6) Monitor
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/siswe… 2/9
6/11/2016 MD5150C Track Drill (Cab, Undercarriage, Engine, Electrical) SEY00001UP (MACHINE) POWERED BY C11 Engine(SEBP7124 16) Systems & C…
Illustration 2 g03819345
Right Side Control Panel
(21) Radio
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/siswe… 3/9
6/11/2016 MD5150C Track Drill (Cab, Undercarriage, Engine, Electrical) SEY00001UP (MACHINE) POWERED BY C11 Engine(SEBP7124 16) Systems & C…
Illustration 3 g03825834
Lower Right Side Control Panel
Note: Make sure that the lever for the hydraulic lockout control is in the LOCKED position before attempting to
start the engine. If the lever is in the UNLOCKED position, the engine start switch will not function.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/siswe… 4/9
6/11/2016 MD5150C Track Drill (Cab, Undercarriage, Engine, Electrical) SEY00001UP (MACHINE) POWERED BY C11 Engine(SEBP7124 16) Systems & C…
The service port is located in the cab and is used by technicians. For additional information contact your Cat
dealer.
Monitor (6)
The monitor is used in order to display various operating information of the machine. For more information on
the operation of the monitor, refer to Operation and Maintenance Manual, "Monitoring System".
NOTICE
The engine start switch must be in the ON position and the engine must
be running in order to maintain electrical functions and hydraulic
functions. This procedure must be followed in order to prevent serious
machine damage.
Note: If the engine fails to start, return the engine start switch key to the OFF position. Return the key to the
start position before you attempt to start the engine again.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/siswe… 5/9
6/11/2016 MD5150C Track Drill (Cab, Undercarriage, Engine, Electrical) SEY00001UP (MACHINE) POWERED BY C11 Engine(SEBP7124 16) Systems & C…
The travel/drill switch is used with the joystick controls to control certain functions of the machine. The center
position of the switch is neutral and disables both travel and drill modes. Press the switch left to enable travel
mode. Press the switch right to enable drill mode. For more information, refer to Operation and Maintenance
Manual, "Joystick Controls"
Turn the feed pressure dial counter clockwise in order to increase the amount of force applied to the drill bit.
Turn the feed pressure dial clockwise in order to decrease the amount of force applied to the drill bit.
Note: The machine will not go into low idle when the compressor is operating. The LED will not turn on when
the air compressor is on.
NOTICE
If the wiper does not operate with the switch in the ON position, turn
the switch off immediately. Check the cause. If the switch remains on,
motor failure can result.
6 Second Delay When the window wiper switch is depressed one time, the left indicator light will turn on. The
window wiper will operate intermittently at six second intervals.
3 Second Delay When the window wiper switch is depressed two times, the middle indicator light will turn on.
The window wiper will operate intermittently at three second intervals.
Continuous Operation When the window wiper switch is depressed three times, the right indicator light will
turn on. The window wiper will operate continuously.
OFF When the window wiper switch is depressed four times, the indicator lights will turn off. The window
wiper stops.
NOTICE
If the washer is used continuously for more than 20 seconds or used
when no washer solution comes out, motor failure can result.
Press the button a fourth time to turn off the dust collector system. For more information, refer to Operation and
Maintenance Manual, "Dust Collector".
Note: The air system must be on in order to enable the dust collector. See this Operation and Maintenance
Manual, "Joystick Controls" for additional information.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/siswe… 7/9
6/11/2016 MD5150C Track Drill (Cab, Undercarriage, Engine, Electrical) SEY00001UP (MACHINE) POWERED BY C11 Engine(SEBP7124 16) Systems & C…
When enabled, the smart drill function senses rotation and air pressure changes and automatically adjusts feed
force, rotation, and hammer output.
Drill Bit Obstruction If the drill bit becomes obstructed, the smart drill function increases the air pressure,
disables the hammer, and reverses the feed direction.
Drill Rod Jam If the drill bit becomes obstructed, the smart drill function increases the air pressure, disables
the hammer, and reverses the feed direction.
Refer to Operation and Maintenance Manual, "Monitoring System" for additional information.
For more information refer to Operation and Maintenance Manual, "Engine and Machine WarmUp".
The heater/air conditioner provides comfort for the operator that is working under various temperature
conditions. For more information on the air conditioning and heater controls, refer to Operation and
Maintenance Manual, "Air Conditioning and Heating Control".
Radio (21)
This machine may be equipped with a radio. For more information, refer to Operation and Maintenance Manual,
"Radio".
This valve is used to control the flow of the water spray system.
The numbers on the valve indicate the rate of water flow. The higher the number the greater the water flow.
Copyright 1993 2016 Caterpillar Inc. Sun Nov 06 2016 12:10:45 GMT0600 (Hora estándar central (México))
All Rights Reserved.
p260jea
Private Network For SIS Licensees.
https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/productsearch/productheaderinfoframeset.jsp&calledpage=/siswe… 9/9