Professional Documents
Culture Documents
A. Straight Polarity
B. Reverse Polarity
C. Constant Polarity
D. Constant Current
A. SMAW
B. GTAW
C. SAW
D. FCAW
3. Which of the following is not the inspector’s responsibilities prior to welding
4. A welding process that uses a consumable electrode and whose shielding gas is generated by the
A. GMAW
B. FCAW
C. SMAW
D. GTAW
5. The welding process that is well suited to making superior root passes because of good penetration is
A. FCAW
B. SAW
C. GMAW-S
D. GTAW
GLOBAL INDUSTRIAL SOLUTIONS
(WELDING QA QC NDT TRAINING INSPECTION MANPOWER ALLIED SERVICES)
H.NO.27-1-65/1/1, SRI SWARNA TOWERS, SRINAGAR, GAJUWAKA, VISAKHAPATNAM,
ANDHRA PRADESH, INDIA – 530026, Website: www.globalindustrialsolutions.in/
Email: info@globalindustrialsolutions.in, globalis.gis@gmail.com, Ph: +91 9959482868
-----------------------------------------------------------------------------------------------------------------------------------------------
B. F, H
C. V
D. F, H, V, O
A. Supplementary variables.
B. Essential variables
9. A welding technique used to obtain desired grain refinement and tempering of the underlying
heat-affected zone in the base metal is known as:
A. Stress Relieving
B. Controlled Deposition Welding
C. Semi-Automatic Welding
A. Pipe with its axis horizontal and rolled during welding so that the weld metal is deposited from above
B. Pipe with its axis vertical and the axis of the weld in the horizontal plane. The pipe is not rotated
C. Pipe with its axis horizontal and with the welding groove in the vertical plane. The pipe shall not be
rotated
D. Pipe with its axis inclined 45º to horizontal without rotating the pipe.
GLOBAL INDUSTRIAL SOLUTIONS
(WELDING QA QC NDT TRAINING INSPECTION MANPOWER ALLIED SERVICES)
H.NO.27-1-65/1/1, SRI SWARNA TOWERS, SRINAGAR, GAJUWAKA, VISAKHAPATNAM,
ANDHRA PRADESH, INDIA – 530026, Website: www.globalindustrialsolutions.in/
Email: info@globalindustrialsolutions.in, globalis.gis@gmail.com, Ph: +91 9959482868
-----------------------------------------------------------------------------------------------------------------------------------------------
12. Deposited weld metal on the face of a weld preparation or surface that will be part of a welded joint is
Referred to as:
A. Buttering
B. Weld Build-Up
C. Cladding
D. Fusion Line
13. A welding technique where the heat and placement of weld passes in deposited weld layers is controlled
so that sufficient heat is provided to temper each previously deposited weld layer is known as:
A. Autogenous Welding.
B. Buttering.
B. That the proposed production weldment is capable of having the required properties
GLOBAL INDUSTRIAL SOLUTIONS
(WELDING QA QC NDT TRAINING INSPECTION MANPOWER ALLIED SERVICES)
H.NO.27-1-65/1/1, SRI SWARNA TOWERS, SRINAGAR, GAJUWAKA, VISAKHAPATNAM,
ANDHRA PRADESH, INDIA – 530026, Website: www.globalindustrialsolutions.in/
Email: info@globalindustrialsolutions.in, globalis.gis@gmail.com, Ph: +91 9959482868
-----------------------------------------------------------------------------------------------------------------------------------------------
C. The corrosion-resistance of the proposed weldment
16. The A-number grouping in ASME Section IX, Table QW-442 is based on
D. Degree Of Deoxidizer
17. For welders, a minimum of 6 in. (150 mm) length of the first production weld must be examined for
performance qualification while a minimum of _______length must be examined for welding operators.
A. 6”
B. 3”
C. 12”
D. 3’
18. What should the inspector do after a rejectable defect has been identified?
A. Consult A Metallurgist
C. Perform Rt Inspection
B. 10
C. 2
D. Several
---END---