Professional Documents
Culture Documents
[SOR-FY-19.257]
Piping Material Classes
- Specification -
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 1 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
REVISION HISTORY
(to be filled from the 2nd issue of the document with details of the previous revision(s))
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 2 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
TABLE OF CONTENTS
1. INTRODUCTION ..............................................................................................................................4
2. PURPOSE .........................................................................................................................................5
2.1. SCOPE .............................................................................................................................................. 5
3. HOLDS .............................................................................................................................................6
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 3 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
1. INTRODUCTION
The Al-Shaheen field is QATAR’s largest oil field. It is a conventional oil field (of approximately 60 m water depth) situated offshore
the State of Qatar approximately 70 km north-north-east of Ras Laffan. The field overlays the giant pre-Khuff gas field known as
North Field.
Thirty-three platforms, including five production hubs, are installed in Al-Shaheen field. These are spread over nine different areas
across the field - Locations A to I. Crude is exported by tanker via tandem offloading from two FSOs which are permanently
moored in the field to two (of three) SPMs. Gas is gathered in a gas grid pipeline system and exported via North Field Alpha.
The field has been developed through several phases and further development phases are envisaged by COMPANY as operator
of the Al-Shaheen concession.
1. Batch - 1: New bridge-linked Wellhead platform (24 Slots) including jackets (DC / FC / EG), shall be installed and the new
WHP’s shall be integrated with their respective existing host platforms (DA / FA / ED) facilities.
2. Batch - 2: New bridge-linked Wellhead platform (24 Slots) including jackets (CE / EH) shall be installed and the new WHP’s
shall be integrated with their respective host platforms (CD / EG) facilities.
3. Batch - 3: New WHP’s (JA / KA) shall be remote connected to a new Process Platform (GE), bridge-linked to existing
facilities GD and corresponding brownfield integration of G location facilities (GA / GC / GD). A new subsea connection will
be connected to GE from F location existing facilities.
F-DBN Project is the EPCIC8 Package of Gallaf Batch 3 which consists of the integration of the new 20” subsea LP Wet Gas pipeline
and riser (by EPCI7) tie-in from the new GE (CPP) and brownfield upgrade scope of existing FA and FB facilities at F-Location,
including RO removal at AB Location with the main purpose of debottlenecking F-location gas and liquid exports.
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 4 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
2. PURPOSE
The COMPANY standard specification SD-NOC-PVV-112 (Piping Material Classes) provides piping material classes and
requirements which are to be followed for the project. The purpose of this document is to further develop the document to include
project requirements for Greenfield and Brownfield scope for F-DBN including FA, FB platforms and associated bridge piping.
The brownfield SoW consists of, but not limiting to the following.
Further, modifications deemed sub-components are stated below, but currently not exhaustive.
2.1. SCOPE
This particular specification is an addendum to COMPANY standard specification SD-NOC-PVV-112 (Piping Material Classes) and
defines additional requirements to those already specified therein.
This specification shall be therefore implemented along with requirements specified in COMPANY standard specification SD-NOC-
PVV-112 unless otherwise updated and/or modified in this document.
In case of any conflict, the more stringent requirement shall be applied. Any conflict shall also be brought to the notice of
COMPANY for resolution which shall be considered for implementing without any schedule or cost impact.
The type of modifications have been defined and indicated in this specification as follows:
- ADD Additional statement(s)/requirement(s) with respect to SD-NOC-PVV-112
- REPLACE WITH Statement(s)/requirement(s) reported into SD-NOC-PVV-112 which needs to be modified.
In case a statement/requirement reported into SD-NOC-PVV-112 shall be deleted, it will be reported in this specification
with the text barred, while the new or additional part will be reported in italics.
- DELETE A particular statement/requirement/section from SD-NOC-PVV-112 which has been deleted.
This document also includes the new Piping Class required for Topside Pipeline Section (PVV) between riser-side ESDV and pig
trap, which is designed as per ASME B31.3 and defined as AD3 (see Appendix 2).
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 5 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
3. HOLDS
The following section/paragraph numbers correspond to those indicated in Company Standard SD-NOC-PVV-112 “Piping Material
Classes” and are those which require an addition or a modification.
• 2. Reference Documents
The full list of relevant regulations, standards and design codes are summarized in the following order of precedence.
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 6 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
[14] [SOR-FY-19.257]-ROMA-
Piping Stress Design Basis
ASFYY-06-640001-0001
[15] [SOR-FY-19.257]-ROMA-
Piping & Topside Pipeline – Basis of Design
ASFYY-06-640002-0001
[16] [SOR-FY-19.257]-ROMA-
Painting – Specification
ASFYY-12-390002-0001
[17] [SOR-FY-19.257]-ROMA-
3D Bend – Piping Special Item Datasheet
ASFAA-06-112003-0001
[18] [SOR-FY-19.257]-ROMA-
Instrument Bulk – Material Take-Off
ASFYY-08-240001-0001
[19] [SOR-FY-19.257]-ROMA-
FA/FB/AB Platforms – Tie-in Schedule
ASFAA-06-202004-0001
[20] [SOR-FY-19.257]-ROMA-
FA Platform – Material Selection Report
ASFAA-12-342002-0001
[21] [SOR-FY-19.257]-ROMA-
Material Selection & Corrosion Control Philosophy
ASYYY-12-262006-0001
ADD (Existing FEED Technical Queries)
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 7 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
[22] WHP03-FEED3-TFM2-MPGF-TQR-
Flare knock Out Drum Sizing Basis
000028_rev01
[23] WHP03-FEED3-TFM2-MPGF-TQR-
Short Radius Elbow
000057_rev00
[24] WHP03-FEED3-TFM2-MPGF-TQR-
Surface Treatment of Pipe Supports
000064_rev00
[25] WHP03-FEED3-TFM2-MPGF-TQR-
Trunnion support on elbow
000081_rev01
[26] WHP03-FEED3-TFM2-MPGF-TQR-
FDBN HP Flare KO Drum Inlet Nozzle Size
000123_rev00
[27] WHP03-FEED3-TFM2-MPGF-TQR-
Isolation Arrangement for 150# Rated System with Toxic Service
000141_rev00
[28] WHP03-FEED3-TFM2-MPGF-TQR-
Flare knock Out Drum Sizing Basis
000028_rev01
[29] WHP03-FEED3-TFM2-MPGF-TQR-
Short Radius Elbow
000057_rev00
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 8 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
[43] WHP03-FEED3-TFM2-MPGF-DEV- FDBN Crude Export Piping & Header Overpressure Excursion
000010_rev01
[44] WHP03-FEED3-TFM2-MPGF-DEV- Deluge Provision on F-DBN Escape Ways
000024_rev00
[45] WHP03-FEED3-TFM2-MPGF-DEV- F-DBN Deluge Nozzles Internal Diameter Less than 5mm
000025_rev00
[46] WHP03-FEED3-TFM2-MPGF-DEV- Excessive Flow through Deluge Valves on FA platform
000026_rev00
[47] WHP03-FEED3-TFM2-MPGF-DEV- Flange support on existing inlet separator (ASFAA-V3401) PSV outlet line
000028_rev00
[48] WHP03-FEED3-TFM2-MPGF-DEV- No slope on closed drain piping to Closed Drain Drum
000029_rev01
[49] WHP03-FEED3-TFM2-MPGF-DEV- SS316L Clad Equipment Subjected to PWHT
000035_rev00
ADD
Definition Description
COMPANY NORTH OIL COMPANY
The Engineering, Procurement, Supply, Construction and Commissioning of EPCIC8:
CONTRACT
F-DBN F-Location Debottlenecking Project Al Shaheen Field – Block 5
CONTRACT / PO No. 4600000750
CONTRACTOR Rosetti Marino Qatar Branch
CALL OFF WORK ordered by COMPANY to be performed by the CONTRACTOR
PROJECT Gallaf Batch-3
The party who has manufactured, assembled, tested and supplied the existing equipment
OEM / VENDOR / and accessories which is proposed to be modified under PROJECT scope AND / OR the
MANUFACTURER party who is responsible for manufacturing, assembling, testing and supplying new
equipment and accessories which is proposed to be installed under PROJECT scope
SHALL Indicates a requirement that is mandatory
SHOULD Indicates a preference
Pressure/Temperature rating of Cu-Ni alloy piping is based on the latest EEMUA 234 revision.
Pressure/Temperature rating of Ni-Al bronze alloy valves is based on ASME B16.24, with yield and tensile strength at
design temperature, established from ASME BPVC Section II – Part D.
• 5. Abbreviations Used
ADD
Abbreviation Description
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 9 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
ADD
The calculation of pipe wall thickness values for each piping class, included the new piping class AD3 for Topside Pipeline
(PVV) section (Wet Gas), has been performed in accordance with ASME B31.3. See Appendix 9 for the detailed calculation.
Vacuum condition (full or partial) has been verified for all piping material classes according to ASME B31.3 Sect. 304.1.3
and corresponding ASME BPVC sections indicated therein. See Appendix 10 for the detailed calculation.
ADD
A minimum corrosion allowance of 3 mm shall be considered for all the topside piping in carbon steel and low alloy steel
materials, including new piping material class AD3 for the topside pipeline (PVV) section, except for galvanized carbon
steel (piping material class AG1) which has a corrosion allowance of 1.3 mm.
ADD
The minimum nominal pipe size (except for instrument and chemical injection tubing) shall be as follows:
o ¾” for local vent/drain connections
o 2” for all other process and utility services
ADD
In case any stainless steel piping class size would require a thickness which is higher than the maximum thickness listed
inside ASME B36.19M, ASME B36.10M shall be used in lieu of ASME B36.19M.
Dimensions of Cu-Ni pipe shall be in accordance with EEMUA 234.
REPLACE WITH
For NPS 18 and above welded pipe will be following ASTM A671 CC65 Class 22 with supplementary requirement S2 (Charpy
V-Notch Test).
ADD
Only low carbon grade SS316L material shall be considered for all Stainless Steel material welded constructions.
Dual grade SS316/316L material is also acceptable, however material properties of SS316L (allowable stress as per ASME
B31.3 Appendix A) shall be considered for all the design calculations.
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 10 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
ADD
Super Austenitic Stainless Steel (6Mo) piping and components shall comply with SD-NOC-PVV-615.
REPLACE WITH
Raised Face (RF): ASME Classes 150 and 300 and 600
Grooved, for Ring Joint (RJ): ASME Classes 600 900 and above.
In order to minimize galvanic corrosion when connecting carbon steel to Corrosion Resistant Alloys (CRA), weld overlay
shall be applied on carbon steel side (flange) according to SD-NOC-PVV-111.
The overlay shall be applied only on the carbon steel flange including the seal joint contact surface, but with no overlap
inside the flange. This requirement is only applicable for:
o Flanges with RJ facing (ASME Class 600 and above)
o Flanges ASME Class 150 and 300 if used with flat graphite gasket
CRA weld overlaid layer shall be 3 mm thick. Weld overlay material shall be Alloy 625 for any CS – CRA coupling. SS309L
is an acceptable weld overlay material for CS – SS316L couplings.
Carbon steel flanges with CRA weld overlay shall be considered as Special Piping Part (SPP) items (ref. new section 6.12).
HOLD 1: A TQ will be issued to ask CPY confirmation that CRA weld overlay on CS flange face is needed only in case of
flat graphite gasket for ratings 150# and 300#.
• 6.6.1 General
ADD
BW fittings shall comply with ASME B16.9
Threaded fittings shall comply with ASME B16.11
Dimensions of non-metallic fittings shall be in accordance with their respective manufacturer information.
Wall thickness of BW fittings shall be the same nominal wall thickness as the attached pipe.
ADD
Only 3D Hot Induction Bends (HIB) shall be used for Topside Pipeline (PVV) Section (if required).
HIBs shall comply with its project datasheet [SOR-FY-19.257]-ROMA-ASFAA-06-112003-0001.
• 6.7.1 General
ADD
Bolting material used for SDBB valves shall also comply with the requirements of SD-NOC-PVV-155.
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 11 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
ADD
Metal seated ball valves shall be used in the fluid services listed inside SD-NOC-PVV-111 Sect. 4.6, and all their technical
requirements shall be in accordance with SD-NOC-PVV-154.
ADD
For dissimilar type check valves requirement, nozzle check valves (short pattern) shall be used instead of swing check
valve if density of the medium if below 0.7 g/cm3.
ADD
Slim Line Double Block and Bleed (SDBB) valves shall be used for all pressure instruments without diaphragm seal, as per
piping hook-up standard, P&ID and P&ID legend.
Integral Double Block and Bleed (IDBB) valves with flanged ends shall be used for instrument connections such as LG, LT,
PG, PT with diaphragm seal as per P&ID and P&ID legend. IDBB valves have been assigned digit “9” for “type of valve”
(ref. SD-NOC-PVV-154 Appendix 11 “Valve tagging philosophy”).
IDBB valves used in lines carrying solid particles/sand shall be metal seated.
According to SD-NOC-PVV-111 Sect- 4.9, SPPs comprise non-standard pressure containing inline items not covered by this
document or valve specifications.
Any SPP shall be assigned an SPP number and be identified as such on the P&IDs.
SPP item tag index and datasheets shall be prepared to include a material description, design, inspection & testing
requirements and any drawing or sketches as required, for each SPP item. SPP tag numbering shall be done according to
SD-NOC-EC-106.
SPP items shall be identified with a permanently attached corrosion resistant metal plate.
A register of SPP items shall be prepared and maintained. This list shall include all data necessary to identify and locate
the SPP items.
High pressure Tubing shall be used for Chemical Injections identified in P&IDs as Tubing. Tubing shall be used for Chemical
Injections for sizes up to and including 1” only. For sizes 1.1/2” and above piping material as per respective piping classes
shall be used.
The Tubing material shall be 6Mo (UNS S31254). All Tubing shall be new, seamless, fully annealed, complying to ASTM
A269 and ASTM A1016/1016M, free from scratches and suitable for bending and flaring.
Impulse tubing for process / utility fluids shall be minimum of ½” OD.
The minimum wall thickness of Tubing shall be selected / finalized based on the final tubing size and line design pressure
/ temperature conditions. Piping shall be used if tubing is not available due to the higher design pressure requirements.
All Tubing fittings shall be of 6Mo (UNS S31254 / UNS N08367) material. Tubing fitting shall be of double compression
type or C&T type. Instrument fittings shall be manufactured by Swagelok or Parker. C&T fittings shall be manufactured by
Swagelok or Parker or BUTECH.
Fitting rating shall be determined based on suitable allowable working pressure.
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 12 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
All valves shall be of 6Mo (UNS S31254) material complying to ASTM A276 or ASTM A479. Valves shall be forged / one
piece bar stock design. Needle valve (except pressure gauge multiport valve) shall have lockable + circular dial type
handle. T-bar handle is not acceptable.
Ball valves may also be one piece forged body, one piece ball and stem design. Handle shall include indication of flow
direction. Ball valves shall be full bore. Ball seals shall have Viton O-ring, PEEK or PTFE seats and PTFE or Graphite packing.
The material of construction and pressure rating of all process connected instrument tubing, fittings, valves & accessories
shall be compatible with and meet applicable piping material specifications / piping class it is connected to for the process
services.
For the two check valves used / installed in series for Downhole Chemical injection tubing, these valves shall be of dissimilar
type. One valve shall be of piston/ball lift type and the other one will be of poppet type.
• NEW SECTION TO BE ADDED: 6.14 Topside Pipeline (PLR) / Topside Pipeline (PVV) Interface
The Topside Pipeline (PLR) section downstream of ESDV (riser side) shall be designed to DNV code, while the Topside
Pipeline (PVV) section upstream of ESDV (platform side) shall be designed to ASME B31.3.
Topside Pipeline (PLR) / Topside Pipeline (PVV) battery limit shall be as per figure below:
HOLD 3: ESDV’s transition piece wall thickness is under definition. The proposal is to have the same wall thickness of
15.09 mm for both ESDV’s transition spool and pipeline (PLR).
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 13 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
4.1. APPENDIXES
Also for Appendixes, in the following only the changes to a specific Appendix No. coming from SD-NOC-PVV-112 will be highlighted.
ADD
NOTE 1: Piping Material Class AD3 developed only for Topside Pipeline (PVV) section designed to ASME B31.3.
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 14 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
TOPSIDE PIPELINE (PVV) PIPING CLASS FOR WET GAS FROM FB TO GE – DATA SUMMARY
GENERAL DETAILS
SIZE NPS 20
PIPE OD mm 508
RATING - 150#
NOTE 1: FB-GE Topside Pipeline (PVV) wall thickness includes bend wall thinning allowance.
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 15 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
Appendix 2 contains only the new piping material class AD3 required for the 20” line from Pig Launcher module to ESDV on FB
platform. All other piping material classes applicable for F-DBN project will remain as they are listed and specified in SD-NOC-
PVV-112.
New piping material class AD3 for Topside Pipeline (PVV) section had been designed to ASME B31.3 and added to the list of
applicable project piping material classes.
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 16 of 20]
APPENDIX 2
[SOR-FY-19.257]-ROMA-ASYYY-06-392010-0001
PIPING MATERIAL CLASS
MATERIAL: LOW TEMPERATURE CARBON STEEL / NACE (A,B,C,2,4) FLANGE RATING: ASME CLASS 150 RF
SERVICES: TOPSIDE PIPELINE (PVV) WET GAS
(SEVERE SOUR SERVICE) (47)
PRESSURE / TEMPERATURE LIMITS (MATL GRP 1.1)
PRESS. (BARG) 17 17
(46) CLASS
AD3
TEMP. (°C) -46 +82 SHEET 1 OF 2
CORROSION ALLOWANCE: 3.0 mm DATE: 16/12/2020 REVISION: 03
NPS 0.5 0.75 1 1.5 2 20 NOTES
SCHEDULE 160 160 160 160 80 STD
WALL THICK (mm) 4.78 5.56 6.35 7.14 5.54 9.53 109
OD (mm) 21.3 26.7 33.4 48.3 60.3 508
PIPE SEAMLESS, ASME B36.10, ASTM A333 GRADE 6 WELDED, EFW 100% RADIOGRAPHY, ASME B36.10, ASTM A671 CC65 CL22 S2 112
ENDS BE
FLANGES
FLANGE WNF, RF, CL150, ASME B16.5, HUB THK AS PER PIPE SCHEDULE, ASTM A350 LF2 CL1 262
BLIND BLIND, RF, CL150, ASME B16.5, ASTM A350 LF2 CL1 262
ELBOW 45/90 DEG LR, ASME B16.9, THK AS PER PIPE SCHEDULE, ASTM A420 WPL6 45/90 DEG LR, ASME B16.9, THK AS PER PIPE SCHEDULE, ASTM A420 WPL6W YYY
30/45/90 DEG INDUCTION BEND, ASME B16.9 / ASME B16.49 / MFG. STANDARD, THK AS PER PIPE
BENDS
FITTINGS
NOTES:
A THIS PIPING CLASS IS DESIGNED TO ASME B31.3
B THIS PIPING CLASS IS SUITABLE FOR PIGGING AND SHALL BE USED FOR WET GAS LINE FROM PIG TRAP ON FA PLATFORM UP TO ESDV-XXXXXX ON FB PLATFORM. WET GAS LINE PROCESS MDMT TEMPERATURE IS -15 °C.
C ALL 20" SIZE COMPONENTS IN PIGGABLE PIPELINE SECTION SHALL BE SUBJECT TO PIG GAUGE TRIAL TEST.
2 MATERIAL SHALL COMPLY WITH NACE MR0175/ISO 15156 PART 2
4 MATERIAL SHALL COMPLY WITH SD-NOC-PVV-612 & WHP03-TFM2-ASYYY-06-392009-0001
APPENDIX 2
[SOR-FY-19.257]-ROMA-ASYYY-06-392010-0001
PIPING MATERIAL CLASS
MATERIAL: LOW TEMPERATURE CARBON STEEL / NACE (A,B,C,2,4) FLANGE RATING: ASME CLASS 150 RF
SERVICES: TOPSIDE PIPELINE (PVV) WET
GAS (SEVERE SOUR SERVICE) (47)
PRESSURE / TEMPERATURE LIMITS (MATL GRP 1.1)
PRESS. (BARG) 17 17
(46) CLASS
AD3
TEMP. (°C) -46 +82 SHEET 2 OF 2
CORROSION ALLOWANCE: 3.0 mm DATE: 16/12/2020 REVISION: 03
NPS 0.5 0.75 1 1.5 2 20 NOTES
SCHEDULE 160 160 160 160 80 STD
WALL THICK (mm) 4.78 5.56 6.35 7.14 5.54 9.53 109
OD (mm) 21.3 26.7 33.4 48.3 60.3 508
NOTES:
46 THIS PIPING CLASS IS DEVELOPED BASED ON PIPELINE DESIGN CONDITIONS (PL-68*) AND NOT BASED ON FULL FLANGE RATING.
47 ALTHOUGH PIPELINE MATERIAL SELECTION REPORT ASSIGNS SSC REGION 2 TO THIS PIPELINE, FOR TOPSIDE (PVV) PART THIS SERVICE IS CONSIDERED AS SEVERE SOUR SERVICE.
109 MILL TOLERANCE SHALL BE IN ACCORDANCE WITH SD-NOC-PVV-112
112 SHALL BE SUPPLIED WITH WELD COEFFICIENT OF 1
202 BRANCH CONNECTIONS SHALL BE IN ACCORDANCE WITH CORRESPONDING BRANCH TABLE IN APPENDIX 3
214 WELDOFLANGE CAN BE USED INSTEAD OF WELDOLET- REFER TO SD-NOC-PVV-112
262 FLANGE FACE FINISH SHALL BE IN ACCORDANCE WITH SD-NOC-PVV-145
359 BOLTS FOR SDBB VALVES
547 SDBB VALVE SHALL BE USED ONLY FOR INSTRUMENT CONNECTION.
YYY TO BE USED ON BARRED TEE BRANCH ONLY (IF REQUIRED.)
ZZZ IDBB VALVES SHALL BE USED FOR INSTRUMENT CONNECTIONS ONLY AS PER PID / LEGEND SHEETS.
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
ADD
Refer to Table 9 for 90 Deg. branching for new piping material class AD3.
Refer to Table 10 for new 45 Deg. branching for piping material classes AD1 (Flare service) and AZ1 (Open Drain service).
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 17 of 20]
Appendix 3 [SOR-FY-19.257]-ROMA-ASFYY-06-390004-0001
TABLE 9
AD3
BRANCH
0.5 T 0.5
1 RT RT T RT BW REDUCING TEE 1
3 W W W RT RT T 3
4 W W W W RT RT T 4
6 W W W W W RT RT T 6
8 W W W W W W RT RT T 8
10 W W W W W W W RT RT T 10
12 W W W W W W W RT RT RT T 12
14 W W W W W W W W RT RT RT T 14
HEADER
HEADER
16 W W W W W W W W RT RT RT RT T 16
18 W W W W W W W W W RT RT RT RT T 18
20 W W W W W W W W W RT RT RT RT RT T 20
24 W W W W W W W W W RC RT RT RT RT RT T 24
26 W W W W W W W W W RC RC RT RT RT RT RT T 26
28 W W W W W W W W W RC RC RT RT RT RT RT RT T 28
30 W W W W W W W W W RC RC RC RT RT RT RT RT RT T 30
32 W W W W W W W W W RC RC RC RT RT RT RT RT RT RT T 32
34 W W W W W W W W W RC RC RC RC RT RT RT RT RT RT RT T 34
36 W W W W W W W W W RC RC RC RC RT RT RT RT RT RT RT RT T 36
40 W W W W W W W W W RC RC RC RC RC RT RT RT RT RT RT RT RT T 40
42 W W W W W W W W W RC RC RC RC RC RC RT RT RT RT RT RT RT RT T 42
NOTES
TABLE 10
0
45 BRANCH TABLE FOR PIPING MATERIAL CLASSES
AD1, AZ1
BRANCH
LTR BW LATROLET
HEADER
16 LTR LTR LTR LTR LTR LTR LTR LC RL RL RL RL L 16
NOTES- 90 degree branch connections shall be used for NPS < 6" in accordance with section 10.5.1 of SD-NOC-ECP-103.
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
DELETE
This Appendix is not applicable (Ref. Sect. 6.9.1 of this document)
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 18 of 20]
Block 5 - AL SHAHEEN FIELD
Document Title PIPING MATERIAL CLASSES
Contract / PO N° Phase
The document relates to [SOR-FY-19.257] – F-DBN – F LOCATION DEBOTTLENECKING PROJECT 4600000750 D
[SOR-FY-19.257]- Rev. Rev. date Status Class
Project ID/Orig. Code Doc. n° ASFYY-06-390004-0001
ROMA A 29-Sep-2021 IFC 1
CTR/VDR Loc./Plat./Mod Discipline Doc. Type System
TBD
Document Number F/Y/Y 06 SPE YY
ADD
This is a new appendix showing the wall thickness calculation details for each piping material class.
The calculation hadn’t been performed for piping material classes AK1 and AR1: CuNi material (AK1) has specified wall thicknesses
depending on the design pressure, while GRE (AR1) has manufacturer’s standard wall thicknesses.
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 19 of 20]
APPENDIX 9
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
Note (1): Sizes not covered by ASME B36.19M, schedules from ASME B36.10M has been used.
APPENDIX 9
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
Note (1): SCH 20 is a special wall thickness for stainless steel. Use ASME B36.10M.
APPENDIX 9
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
Minimum Pipe Wall Thickness shall be calculated according to ASME B31.3 using the following formula
Legenda:
ADD
This is a new appendix showing the wall thickness calculation details under external pressure only for piping material class AD1,
because HP Flare KO Drum is the only equipment designed for FV design condition.
The calculations show that FV verification fails for sizes 18”, 26” and 28”.
However, as per discussion with CPY, vacuum condition is unlikely for FA platform HP Flare system. Therefore, CTR asks to deviate
from requirement of FV for piping material class AD1 sizes 18”, 26” and 28” through a TQ, which is still under drafting (HOLD 2).
The information contained in this document is the proprietary to North Oil Company.
It must not be reproduced, stored, disclosed to any third party or used for any purpose not authorized by North Oil Company.
Printed documents are uncontrolled and considered as "for information only". Reference should always be made to the on-line EDMS for the updated version
[Page 20 of 20]
APPENDIX 10
inch 1/2" 3/4" 1" 1.1/2" 2" 3" 4" 6" 8" 10" 12" 14" 16" 18" 20" 24" 26" 28" 30" 32" 34" 36"
Do 21,3 26,7 33,4 48,3 60,3 88,9 114,3 168,3 219,1 273,1 323,9 355,6 406,4 457 508 610 660 711 762 813 864 914
t 4,78 5,56 6,35 7,14 5,54 5,49 6,02 7,11 6,35 6,35 8,38 7,92 7,92 7,92 9,53 9,53 9,53 9,53 12,7 12,7 12,7 12,7
t*MT-C 1,1825 1,865 2,55625 3,2475 1,8475 1,80375 2,2675 3,22125 2,55625 2,55625 4,3325 3,93 3,93 3,93 5,33875 5,33875 5,33875 5,33875 8,1125 8,1125 8,1125 8,1125
Do/t 18,012685 14,3164 13,066 14,873 32,6387 49,2862 50,4079 52,2468 85,7115 106,836 74,7605 90,4835 103,41 116,285 95,1534 114,259 123,624 133,177 93,9291 100,216 106,502 112,666
L/Do 938,96714 749,064 598,802 414,079 331,675 224,972 174,978 118,835 91,2825 73,2332 61,7475 56,243 49,2126 43,7637 39,3701 32,7869 30,303 28,1294 26,2467 24,6002 23,1481 21,8818
USED L/D0 50 50 50 50 50 50 50 50 50 50 50 50 49,2126 43,7637 39,3701 32,7869 30,303 28,1294 26,2467 24,6002 23,1481 21,8818
A 0,00335 0,006 0,0069 0,0051 0,001 0,00043 0,00043 0,00042 0,00015 9,5E-05 0,0002 0,00015 0,0001 8,2E-05 0,00011 8,5E-05 0,00007 6,1E-05 0,00013 0,00011 0,0001 0,00009
B 117 120 120 120 87 47 47 46 21
Pa 8,6605634 11,176 12,2455 10,7578 3,55406 1,27148 1,24319 1,17392 0,23101 0,11738 0,37453 0,21882 0,12765 0,09308 0,1526 0,0982 0,07474 0,06046 0,18269 0,14489 0,12394 0,10544
Pa1
Pa2
Chosen Pa
Pa > P? YES YES YES YES YES YES YES YES YES YES YES YES YES NO YES NO NO NO YES YES YES YES
HOLD 2: Even though the sizes 18", 24", 26" and 28" fail the FV wall thickness calculation, for FA platform HP Flare system vacuum condition is unlikely.
Therefore, CTR asks to deviate from FV requirement for piping class AD1 inches 18", 24", 26" and 28".