Professional Documents
Culture Documents
..\WorkInstructions\23.pdf
For Mechanical Check/Visual Inspection and Electrical Tests Use C.L. of W.I.23
Bay / Location:
Make :
Phase A B C
Sr.No.
Ratio
Class
Type
Rct
Burden
Vkp
Imag
Application
ELECTRICAL TEST:
Instrument : Make:
Factory
Measured Value in Ohm
Value in
Terminal Ratio Ohms at 75ْ
ْ C 75ْ C C % Error Remarks
Phase B: Amb.Temp. : ْ C
Factory
Measured Value in Ohm
Value in
Terminal Ratio Ohms at 75ْ
ْ C 75ْ C C % Error Remarks
Phase C: Amb.Temp. : ْ C
Factory
Measured Value in Ohm
Value in
Terminal Ratio Ohms at 75ْ
ْ C 75ْ C C % Error Remarks
NOTE: 1.
Rc = Calculated value at 75 C
Rm = Measurement value which contained a measurement cable.
NOTE: 2
Calculated 75 C Rc = (Rm-Rx) x (234.5+75)
(234.5+Ta)
NOTE: 3
3. Polarity Test:
Core 1
4. Ratio Test:
Phase B:
Phase C:
Primary Test Current Secondary Measured
Terminal Ratio Current % Error
Criteria: The %age error for Magnetizing current shall be within +/- 5% of the factory Test Report.
Note: All CT cores shall be demagnetized after the tests are carried out.
Current from
Sl.No. Voltage (V) Current (mA) Magnetizing Curve %age Error
(mA)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Current from
Sr.No. Voltage (V) Current (mA) Magnetizing Curve %age Error
TEST DATE: TEST EQUIPMENT CALIB.DATE & DETAIL
Current from
Sr.No. Voltage (V) Current (mA) Magnetizing Curve %age Error
(mA)
1
2
3
4
6. Burden Test:
Injected Current:
Phase Description Core-1 Core-2 Core-3 Core-4 Remarks
A Terminal No.
Ratio
Measured Voltage (V)
7. PHASE TEST:
Test instrument :
Make :
Model/SI No :
Oil Temp.gauge reading :
Criteria :
Amp temp
Measurements Test Voltage(Kv) Capacitance (nF) Power factor % Power factor % after
measured correction
CH+CHL
CH
CHL
CL+CLH
CL
CLH
11. INTERCORE CORE COUPLING TEST: (verify for differential core only)
Core -1 Excite Voltage across Volt across Volt across Volt across
Core -2, all other sec. Core -3, all other sec. Core -4 all other sec. Core -5 all other sec.
wind. shorted & wind. shorted & Primary wind. shorted & wind. shorted &
Primary open open Primary open Primary open
Core -2 Excite Voltage across Voltage across Volt across Volt across
Core -1, all other sec. Core -3, all other sec. Core -4 all other sec. Core -5 all other sec.
wind. shorted & wind. shorted & Primary wind. shorted & wind. shorted &
Core -3 Excite Voltage across Voltage across Volt across Volt across
Core -1, all other sec. Core -2, all other sec. Core -4 all other sec. Core -5 all other sec.
wind. shorted & wind. shorted & Primary wind. shorted & wind. shorted &
Primary open open Primary open Primary open
Core -4 Excite Voltage across Voltage across Voltage across Voltage across
Core -1, all other sec. Core -2, all other sec. Core -3, all other sec. Core -5, all other sec.
wind. shorted & wind. shorted & Primary wind. shorted & wind. shorted &
Primary open open Primary open Primary open
Core -5 Excite Voltage across Voltage across Voltage across Voltage across
Core -1, all other sec. Core -2, all other sec. Core -3, all other sec. Core -5, all other sec.
wind. shorted & wind. shorted & Primary wind. shorted & wind. Shorted &
Primary open open Primary open Primary open
Note: To determine if there is coupling between cores, the excitation test should be done, and the voltage across the full
winding on each of the adjacent cores should be measured one at a time with all other current transformer secondary
windings shorted. A high impedance voltmeter (20000Ω/ V or greater) will read less than 1V or 2 V if there is no inter-core
coupling. If there is coupling, the voltage will be substantially higher (Reference IEEE StedC57.13.1-2006)