Professional Documents
Culture Documents
Plumbing
Plumbing
PLUMBING CODE
Instructions: Select the correct answer for each of the following questions. Mark
only one answer for each item by
shading the box corresponding to the letter of your choice on the answer sheet
provided.
MULTIPLE CHOICE
1. Any group of two or more similar, adjacent fixtures which discharge into a
common horizontal waste or soil branch.
3. What is the minimum setting distance of a urinal from its center to any
sidewall?
4. No urinal shall be set closer than ___ meter from its center to any
sidewall or partition
c.
0.6
a. 0.3 d.
0.75
b. 0.375
5. Drains in gutters shall be spaced not more than ____ meters apart.
c.
4.9
a. 3 d.
5
b. 4.5
a. 25.4 mm c.
51.0 mm
b. 31.0 mm d.
75.0 mm
Page 1 of 12
8. What is the water closet ratio or water closet fixtures per person for a
hospital ward room?
10. A space with a volume a less than 1.4 cu. m. with 250 kg calorie of aggregate
input rating of fuel burning
appliances installed in that space.
a. Air – space c.
dead space
b. confined space d.
unconfined space
a. bidet c. privy
b. hopper d.
latrine
Page 2 of 12
12. Plumbing Law of the Philippines.
a. RA 1378
c. PD 856
b. RA 1364
d. PD 1096
13. Refers to an arbitrary quantity in terms of which the load- producing effects
or water requirements on the plumbing
system of different kinds of plumbing fixtures are expressed in some
arbitrarily chosen scale.
14. Plumbing fixtures, devices and appurtenances shall be supplied with water in
sufficient volume and at pressure
adequate to enable them to function satisfactorily and without undue noise
under all normal conditions of use.”
a. Plumbing Appliance
c. Plumbing Appurtenance
b. Plumbing Fixture
d. All of the above
17. As per NPCP 1959, The minimum plumbing permit charged for the 1st Plumbing
Unit is.
a. 5 Php
c. 500 Php
b. 200 Php
d. 1000 Php
18. Lowest portion of the interior part of any pipe or conduit that is not
vertical.
a. crown weir c.
Top dip
b. Spring line d.
Invert
20. The drainage pipe running from outside a buildings foundation to the main
sewer is called
a Building drain c
Waste drain
b Sewer d
Storm drain
a Drain pipe c
Vent pipe
b Conductor d
Soil pipe
22. The distance of vent from trap seal shall not be more than:
Page 3 of 12
a. 1.20 m c.
1.50 m
b. 0.60 m d.
2.00 m
24. This fixture is designed to wash an individual with large volumes of water
when there is a chemical spill, or any
hazardous material that is spilled on an individual.
25. A receptacle other than a trap attached to a plumbing system in which water
or waste maybe collected or retained
for ultimate discharge into the plumbing system.
26. A plumbing fixture used for washing the middle part of the body, especially
the genitals.
27. An approved plumbing fixture or device of such materials, shape and capacity
to adequately receive the discharge
from indirect waste pipe.
28. An approved tank or pit which receives sewage or wastewater and is located
below the normal grade of the gravity
system and must be emptied by mechanical means.
29. A drain connecting the compartments of certain fixture to its trap is called
30. Consist of two independently acting internally loaded check valve, four
properly located test cocks and 2 isolation
gate valves.
a. pressure breaker c.
pressurized isolation valves
b. pressure vacuum breaker backflow d.
double check valves
prevention
31. No drain or vent piping shall be drilled and tapped for making connections
thereto, and no cast iron soil pipe shall
be ____.
a. caulked b.
threaded
Page 4 of 12
c. screwed
d. bell and spigot
a. 16th Century
c. 18th Century
b. 17th Century
d. 19th Century
34. Air test, air is forced into the pipe system until there is a uniform
gauge pressure of _____ or sufficient to balance
a column of mercury 254 mm in height.
a. 34.5 kPa
c. 35.4 kPa
b. 43.5 kPa
d. 45.3 kPa
a. percolation test
c. permeability test
b. adsorption test
d. cohesion test
36. If vertical pipe that collects rain water from roof is located inside
the building, it is called?
a. Downspout
c. Gutter
b. Leader
d. Stack pipe
37. Each vent opening shall terminate not less than ____ meters from, or at
least ____ meter above any openable
window, door opening, air intake or vent shaft.
a. 2.0, 1.0
c. 3.0, 0.9
b. 2.5, 0.9
d. 3.0, 1.0
38. Which of the traps are allowed:
a. S-Trap c.
Bell Trap
b. Drum Trap d.
Crown vented trap
39. That part of the plumbing system extending from a point 4 or 5 ft from
the inner face of the foundation wall of a
building to the junction with another sewer
a House sewer
c Sanitary sewer
b Storm sewer
d Sewer pipe
Page 5 of 12
a Insanitary c
Healthful
b Unhealthy d
Sanitary
a Ejector c
Screw
b Ram d
Hard pump
42. Building sewer or drainage pipe shall be placed with the same trench with
water service pipe.
a False c
Maybe
b Not same d
True
44. Piping which shall not be installed under or within 2 ft. at any building or
structure
a cast iron c
copper
b plastic d
asbestos cement
45. What valve is required ahead of each water supplied appliance, each slip
joints or non-metallic connection?
a flow valve c
control valve
b check valve d
solenoid valve
46. Every building in which plumbing fixtures are installed shall have a
connection to a
a Drywell c
storm water
b cesspool d
public or private sewer
47. The movement of water through the surface of a soil and into the soil below
the surface is
a storm meter run off c
evaporation
b depression d
infiltration
48. The quantity of water required to be supplied to every plumbing fixture shall
be represented by
49. A pit or receptacle at allow point to which the liquid waste are drain
a canal c
tank
b sump d
cistern
50. A fixture vent pipe increased one pipe size its entire length
Page 6 of 12
a may exceed the maximum c
will increase venting efficiency
horizontal length limited by code d
will reduce the cost of installation
b will be a better workmanship job
a 5 c
12
b 15 d
10
52. A storm drain sometimes located under the basement floor within the walls of
the
53. The lowest piping system that receives the discharge from soil waste and
other drainage pipe
a Waste pipe c
Building sewer
b A building drain d
Soil pipe
a Branch vent c
Continuous vent
b Relief vent d
Circuit vent
55. A piping system designed to control and conveys excess ground water to a
suitable location.
a Drain pipe c
Vent pipe
b Conductor d
Soil pipe
57. A type of urinal in which the bowl is elongated and attached to the floor. A
front piece conceals the internal
elements of the urinal located at the part of it
a. flashing c.
clean out
b. ferrule d.
cap
59. Vertical drainage lines to horizontal drainage line shall enter through __
deg branches.
a. 90 c.
45
b. 60 d.
30
60. Sewage which may be deleterious to surface or subsurface waters, shall not be
___ into the ground or into any
waterway unless not treated to an acceptable form.
Page 7 of 12
a. collected c.
discharge
b. absorbed d.
conveyed
61. The vertical distance between the top dip and the crown weir
a trap seal c
dry seal
b water seal d
invert elevation
62. Disposal of sewage, human excreta or other waste waters shall be done through
an approved ___________ and
storm drainage system.
a cesspool c
digestive chamber
b excreta d
leaching tank
63. The plugging of an oakum, lead or other materials that pounded into the
annular space.
a plugging c
cementing
b caulking d
soldering
64. The unobstructed vertical distance through the free atmosphere between the
lowest opening from any pipe or
faucet supplying water to a tank, plumbing fixture, or other device and the
flood level rim of the receptacle.
a air break c
air gap
b air vacuum d
development length
65. The flow of water or other liquids, mixtures, or substances into the
distributing pipes of potable supply of water
from any source or sources other than its intended source
66. A flange that closes the end of the pipe where there is no opening for the
passage of water
a blind flange c
dead end flange
b blank flange d
plug
a orifice c
riser
b blow-off d
overflow
68. What is the general term applied to any vertical line of soil, waste or vent
piping?
a stack pipe c
wet pipe
b soil pipe d
waste pipe
69. Water closet bowls for public use shall be the _____ bowl types equipped with
open front seats.
a. Round
c. Square
b. Elongated
d. Rectangular
Page 8 of 12
b. Prevent sagging c.
All of the above
d.
None of the above
71. The lowest piping system that receives the discharge from soil waste and
other drainage pipe
a Waste pipe c
Building sewer
b building drain d
Soil pipe
a. septic vault c.
leaching cesspool
b. privy d.
latrine
73. Upon issuance of plumbing permit, plumbing installation shall commence within
a No limit c
One year
b One month d
Six months
a Globe valve c
Butterfly valve
b Ball-cock d
Gate valve
a. 1.0, 3.0 c.
2.0, 3.0
b. 1.8, 3.0 d.
1.2, 3.0
77. Vertical Screwed Pipe - Iron Pipe Size (IPS) shall be supported at ________.
78. The strainers serving shower drains shall have waterway equivalent to the
area of the _______
a. Inlet c.
Tailpiece
b. Outlet d.
None of the above
79. For “Sacrarium" cupsink at church altar and Baptistries font outlet shall
discharge direct to the ground and not
connected to the sanitary drainage system.
c.
Ground
a. Sanitary drainage system d.
Floor Drain
b. Septic tank
80. No water closet or bidet shall be set closer than _____ meter from its center
to any side wall or obstruction
a.
0.3
Page 9 of 12
b. 0.375 c.
0.6
d.
0.75
81. No water closet or bidet shall be set closer than _____ meter from its center
to any similar fixture
c.
0.6
a. 0.3 d.
0.75
b. 0.375
82. All pipings passing under or through walls shall be protected from breakage
with __________.
83. All pipes passing through or under cinders or other corrosive materials shall
be protected from external corrosion
by encasing same with ___________ or in other approved manner.
a. 0.50% c.
2%
b. 1% d.
3%
85. Where it is impracticable to obtain a 2% slope, any such pipe drainage pipe
with size _____ or larger in diameter
may have a slope of 1% provided it is first approved by the Administrative
Authority.
a. 51 mm c.
102 mm
b. 76 mm d.
127 mm
86. The bottom of all pipe trenches deeper than the footing of any adjacent
building or structure and parallel to it must
be at least ______ therefrom, unless permission is granted by the
Administrative Authority.
a. 30 degrees c.
60 degrees
b. 45 degrees d.
90 degrees
a. 0.3, 0.6 c.
0.6, 0.3
b. 0.3, 0.3 d.
0.6, 0.6
88. Changes in direction of drainage piping shall be made by the use of approved
pipe fittings and shall be of the
angles presented by a 22 1/2° bend, 45° bend, 60° bend or other approved
fittings of ____ sweeps.
a. steep c.
longer
b. shorter d.
larger
Page 10 of 12
89. Request for inspection by the master plumber to the administrative authority
is required to be made in advance at
least before the work to be tested.
a. 12 hours c.
36 hours
b. 24 hours d. 8
hours
90. No chemical toilet shall be installed in any building unless first approved
by the:
a. Health officer c.
building and safety
b. Architect d.
zoning administrator
91. Air pressure in drainage pipes greater than the atmospheric pressure
a. Standard pressure c.
back pressure
b. Normal pressure d.
barometric pressure
a. P-trap c.
Drum trap
b. Grease trap d.
House trap
a. 1300 mm c.
900 mm
b. 1200 mm d.
1500 mm
94. A fitting that is necessary for maintenance and is required for every change
of direction?
a. P-trap c. Wye
b. Elbow d. Clean
out
95. A pipe that collects discharge direct from the plumbing fixture?
97. Roof deck strainers for use on sun decks, parking decks and similar occupied
areas shall be an approved ____
type which is level with the deck.
a. dome b.
flat-surface
Page 11 of 12
c. close d.
non-slippery
98. No building sewer shall be smaller than ___ mm diameter nor less in size
than the building drain.
a. 100 c.
150
b. 125 d.
170
99. The bottom of the water pipe at all points, shall be at least ___ above the
top of the sewer or drain line.
a. 1.0 c.
0.6
b. 0.3 d.
3.0
100. Water pipe joints shall be installed not less than ___ meters away from
sewer line in both directions.
a. 1.0 c.
1.5
b. 0.3 d.
3.0
Page 12 of 12
Mid Mock Board Exam
Physical Review Center in Iloilo City
For July 2019 Master Plumber Board Exam
MULTIPLE CHOICE
a) yard
b) court
c) lot
d) parcel
a) pollution
b) contamination
c) high hazard
d) all of the above
4. The end of a pipe which fits into a bell. Also a word used synonymously
with faucet
a) bib
b) spigot
c) male end
d) connection
a) relief vent
b) loop vent
c) main vent
d) stack vent
a) plumbing system
b) plumbing fixtures
c) plumbing appliance
d) plumbing appurtenance
10. Include all valves and controls used in plumbing systems which are accessible.
a) regulators
b) plumbing system
c) cleanout
d) regulating equipment
11. A drain connecting the compartments of a certain fixture to its trap is called.
12. Water satisfactory for drinking, culinary and domestic purposes and meets the
requirements of the Philippine National
Standards for Drinking Water.
a) Clean water
b) potable water
c) drinkable water
d) mineral water
15. The maximum vertical depth of liquid that a trap will retain measured between
the crown weir and the top of the dip of the
trap.
a) trap limit
b) trap
c) trap arm
d) trap seal
16. Any system of continuous piping, which is the principal artery of the system
where branches are connected.
a) main
b) main sewer
c) main vent
d) stack
17. A large opening in a sewer line or part of a plumbing system constructed with
sufficient size for a man to gain access therein
for maintenance purposes and facility for changes of line and/or grade of
pipe line.
a) access
b) confined space
c) manhole
d) none of the above
18. The extension of a soil or waste stack above the highest horizontal drain
connected to the stack.
a) vent stack
b) stack vent
c) main vent
d) all of the above
19. An approved tank or pit which receives sewage or wastewater and is located
below the normal grade of the gravity system
and must be emptied by mechanical means.
a) subsoil drain
b) underground water
c) basement water
d) sump
20. That portion of rainfall or other precipitation which runs off over the
surface of the ground.
a) Storm water
b) Run off
c) Ground water
d) Surface water
21. A water basin used for swimming designed to accommodate many bathers at a
time and properly connected to a disposal
system, fills and draws water supply or provided with approved water
purification and recirculation system.
a) Lap pool
Plumbing Code and Sanitation, Design & Installation
Chapter 10 4
b) jacuzzi
c) swimming pool
d) community bath tub
a) tapped tee
b) trap
c) trap arm
d) trap seal
a) chase
b) sump
c) shaft
d) open
24. .A hose fitting with clapper valves for combining the flow from two or more
lines of hose into a single stream. The inlet fitting
of a fire standpipe located above ground level.
a) Hose bib
b) twin line
c) siamese connection
d) dual pipes
25. A suction created by the flow of liquids in pipes. A pressure less than
atmospheric.
a) siphonage
b) back-siphonahe
c) back flow
d) back pressure
26. Hemp or old hemp rope soaked in oil or tar to make it waterproof.
a) oakum
b) bitumen
c) vulcaseal
d) putty
27. Any branch in a building drain other than the primary branch.
a) secondary branch
b) first branch
c) storm drain line
d) service branch
28. A loosely lined excavation in the ground which receives the discharge of a
septic tank and designed to permit the effluent
from the septic tank to seep through pit bottom and sides .
a) leaching pit
b) septic vault
c) trench
d) seepage pit
29. Tube made of plastic material and colored black. The cross-sectional shape is
normally oval and is denoted by its outside
diameter or O.D. Normally used as water service connection from main to
meter.
a) pe
Plumbing Code and Sanitation, Design & Installation
Chapter 10 5
b) pb
c) ppr
d) pvc
a) Shielded coupling
b) union
c) slip joint
d) bushing
a) Main stack
b) Soil riser
c) Building drain
d) Soil stack pipe
32. A pipe or shaft to convey foul air from a plumbing fixture or a room to the
outer air.
a) loop vent
b) local vent
c) individual vent
d) vstr
a) pedestal
b) c/l
c) receptor
d) rim
34. A water supply pipe, which extends vertically to one full story or more to
convey water into pipe branches or plumbing fixtures.
a) stack
b) riser
c) main
d) vertical line
a) pipe
b) tube
c) culvert
d) chase
a) leaching cesspool
b) septic tank
c) privy
d) leaching pit
a) Black water
Plumbing Code and Sanitation, Design & Installation
Chapter 10 6
b) grey water
c) liquid waste
d) waste
a) plumbing system
b) plumbing fixtures
c) plumbing appliance
d) plumbing appurtenance
39. Wastes which require some special methods of handling such as the use of
indirect waste piping and receptors; corrosion-
resistant piping sand, oil or grease interceptors, condensers or other
pretreatment facilities.
a) Sacrarium waste
b) Domestic waste
c) Special wastes
d) Hazardous waste
41. Includes all potable water supply and distribution pipes, all plumbing
fixtures and traps; all sanitary and storm drainage
systems; vent pipes, roof drains, leaders and downspouts; and all building
drains and sewers, including their respective joints
and connections; devices, receptacles, and appurtenances within the property
water lines in the premises: potable, tap, hot
and chilled water pipings, potable water treating or using equipment; fuel
gas piping; water heaters and vents for same.
a) plumbing system
b) plumbing unit
c) plumbing plans
d) plumbing design
42. The horizontal distance of trap arms when its diameter is 32 mm.
a) 0.76 m
b) 1.07 m
c) 1.52 m
d) 3.05 m
a) sewer
b) drainage
c) sanitary sewer
d) main sewer
Plumbing Code and Sanitation, Design & Installation
Chapter 10 7
44. A minimum standard quantity of plumbing fixtures that discharge wastes into a
plumbing installation including: one (1) water
meter, one (1) water closet, one (1) lavatory, one (1) shower head and drain
tor a bathtub or shower stall, one (1) kitchen
sink, one (1) laundry tray and three (3) floor drains and four (4)
faucets/hose bibs.
a) Fixture unit
b) Quantity
c) Flow rate
d) plumbing unit
45. The normal force exerted by a homogeneous liquid or gas, per unit of area on
the wall of the container
a) viscosity
b) residual pressure
c) pressure
d) static pressure
46. The pressure available at the fixture or water outlet; allowance is made for
pressure drop due to friction loss, head, meter
and other losses in the system during maximum demand period.
a) viscosity
b) residual pressure
c) pressure
d) static pressure
47. Of the building drain is the single sloping drain from the base of a stack to
its junction with the main building drain.
a) primary branch
b) branch
c) secondary branch
d) building sewer
49. A building sewer, which receives the discharge from more than one building
drain and conveys it to a public sewer, private
sewage disposal system, or other points of disposal.
a) Public sewer
b) Primary branch
c) Common sewer
d) Private sewer
50. a pipe connected from building gutter to the downspout or conductor.
a) leader
b) gutter
c) roof drain
d) splash
51. Laundry equipment that does not have integral strainers shall discharge into
an interceptor having a wire basket or similar
device, that is removable for cleaning and that will prevent passage into the
drainage system of solids ____ or larger in
maximum dimension, such as string, rags, buttons, or other solid materials
detrimental to the public sewerage system.
a) 10.7 mm
Plumbing Code and Sanitation, Design & Installation
Chapter 10 8
b) 12.7 mm
c) 17.3 mm
d) 21.1 mm
a) privy
b) cesspool
c) leaching cesspool
d) private sewer
53. PVC drainpipes are manufactured with toxic components and are color-code,
except:.
a) gray
b) orange
c) black
d) brown
55. The vertical distance between the dip and the crown weir of a trap.
a) P-trap
b) diameter
c) tailpiece
d) seal
56. Tube made of plastic material and colored black. The cross-sectional shape is
circular and is denoted by its outside diameter
or O.D.
a) pe
b) pb
c) ppr
d) pvc
57. An approved plumbing fixture or device of such materials, shape and capacity
to adequately receive the discharge from
indirect waste pipes, constructed and located to be readily cleaned.
a) receptor
b) drain
c) p-trap
d) rim
58. A water closet consisting of a continuous trough containing water. The trough
extends under two or more adjacent seats.
Prohibited by health authorities for permanent installations.
a) one-piece
b) wall-hunged
c) latrine
d) pail-wash
Plumbing Code and Sanitation, Design & Installation
Chapter 10 9
60. A fixture designed for the washing of the hands or face. Sometimes called a
wash basin.
a) kitchen sink
b) catch basin
c) bidet
d) lavatory
61. The installation of all pipings and fitting parts of the plumbing system,
which can be completed prior to the installation of
fixtures and accessories.
a) roughing-in
b) fit outs
c) plumbing system
d) pipe lines
62. The wastewater containing human excrements and liquid household waste. Also
called domestic sewage.
a) sewage
b) sewerage
c) sanitary sewage
d) grey water
a) STP
b) privy
c) septic tank
d) cesspool
64. The principal artery of the venting system to which vent branches are
connected.
a) main vent
b) vent stack
c) stack vent
d) loop vent
65. The pipe from the street water main or other source of water supply to the
building served.
a) sewer
b) sewerage
c) sanitary line
d) drainage
Plumbing Code and Sanitation, Design & Installation
Chapter 10 10
67. An approved elastomeric sealing gasket with an approved outer shield and a
tightening mechanism.
a) shielded coupling
b) bitumen
c) slip joint
d) oakum
68. Any pipe, which conveys the discharge of water closet, urinal or fixtures
having similar functions, with or without the
discharges from other fixtures to the building drain or building sewer.
a) stack
b) sanitary line
c) branch
d) soil pipe
69. Made up two 90° bends with inside and outside threads, flanged or welded
fittings~ and applied also to a one hundred eighty
degrees bend in copper tubings.
a) goose neck
b) p-trap
c) return bend
d) valves
70. A pipe joint obtained by joining metal parts with metallic mixtures or alloys
which melt at a temperature below 427 degrees
centigrade and above 149 degrees centigrade.
a) brazed joint
b) soldered joint
c) welded joint
d) flanged joint
71. That portion of the rainfall or other precipitation which runs off over the
earth surface after a storm.
a) storm water
b) rain water
c) run off
d) groundwater
72. That portion of a building included between the upper surface of any floor
and the upper surface of the floor next above.
a) floor line
b) partition
c) leveling
d) storey
73. An underground drainpipe that receives only subsurface or seepage water and
convey it to a sump for disposal by gravity
flow or by lift pump.
a) subsoil drain
b) under drain
c) ground pipe
d) building drain
a) plumbing system
b) plumbing fixtures
Plumbing Code and Sanitation, Design & Installation
Chapter 10 11
c) plumbing appliance
d) plumbing appurtenance
75. The Administrative Authority or the officer charged with the administration
and enforcement of the National Plumbing Code,
or his regularly authorized deputy.
76. That portion of a fixture drain between a trap and the vent.
a) tapped tee
b) trap
c) trap arm
d) trap seal
77. Not more than ___ trap shall be permitted on a trap arm.
a) One
b) Two
c) Three
d) Four
78. It is provided, however, that one trap may serve a set of not more than three
(3) single compartment sinks or laundry tubs of
the same depth or three (3) lavatories immediately adjacent to each other and
in the same room if the waste outlets are not
more than _____ apart and the trap is centrally located when three (3)
compartments are installed.
a) 0.5 m
b) 0.75 m
c) 1.0 m
d) 1.2 m
a) Underground pit
b) cesspool
c) privy vault
d) sump
80. A common sewer directly controlled by public authority to which all abutters
have equal rights of connections.
a) public sewer
b) private sewer
c) primary branch
d) main sewer
82. The purpose for which a building is used or intended to be used. The term
shall also include the building or room housing
used.
a) function
Plumbing Code and Sanitation, Design & Installation
Chapter 10 12
b) design
c) occupancy
d) usage
a) branch
b) lateral
c) offset
d) none of the above
84. The vertical distance between a fixture outlet and the trap weir shall be as
short as practicable, but in no case shall the
tailpiece from any fixture exceed _____ in length.
a) 0.15 m
b) 0.30 m
c) 0.50 m
d) 0.60 m
85. The horizontal distance of trap arms when its diameter is 51 mm.
a) 0.76 m
b) 1.07 m
c) 1.52 m
d) 3.05 m
a) True
b) False
c) Maybe
d) Not stated in the code
a) viscosity
b) residual pressure
c) pressure
d) static pressure
88. Each fixture trap shall have a water seal of not less than ___ and not more
than ____ deep except where a deeper seal is
found necessary by the Administrative Authority for special conditions.
Traps.
a) 26 – 51 mm
b) 51 – 75 mm
c) 26 – 71 mm
d) 51 – 102 mm
89. When subject to reverse flow of sewage or liquid waste, such drains shall be
equipped with an approved _____.
a) Gate valve
b) Butterfly valve
c) Globe valve
d) Backwater valve
Plumbing Code and Sanitation, Design & Installation
Chapter 10 13
90. No individual grease trap shall be installed for a facility that has an
approved rate of flow of more than ____ nor less than
_____, except when specially approved by the Administrative Authority.
91. No such collected grease shall be introduced into the drainage piping and
public or private sewer.
a) True
b) False
c) Maybe
d) Not stated in the code
92. Each grease trap shall have an approved water seal of not less than ____ in
depth or the diameter of its outlet, whichever is
greater.
a) 26 mm
b) 51 mm
c) 76 mm
d) 102 mm
93. Whenever the discharge of a fixture or drain may contain solids or semi-
solids heavier than water that would be harmful to a
drainage system or cause a stoppage within the system, the discharge shall be
through a ________.
a) Grease interceptor
b) Clarifier
c) Sand interceptor
d) None of the above
94. Each soil or waste stack which extends ____ or more stories above the
building drain shall be served by a parallel vent stack
which shall extend undiminished in size.
a) 5 storeys
b) 9 storeys
c) 10 storeys
d) 12 storeys
95. No more than _____ of the total permitted length, per Table 7-5 of any
minimum sized vent shall be installed in a horizontal
position.
a) 1/3
b) 1/2
c) 1/4
d) Same size
96. The pipe or tubing that connects the outlet of a plumbing fixture to the
trap.
a) drain
b) tailpiece
Plumbing Code and Sanitation, Design & Installation
Chapter 6 and 7 14
c) trap arm
d) trap seal
97. A tee with the branch tapped to receive a threaded pipe or fittings.
a) tapped tee
b) tailpiece
c) trap arm
d) trap seal
98. The vertical main of a system of soil, waste or vent pipings extending
through one or more stories and extended thru the roof.
a) stack
b) main
c) vstr
d) vent
a) riser
b) standpipe
c) stack
d) water line
PLUMBING ARITHMETIC
Instructions: Select the correct answer for each of the following questions. Mark
only one answer for each item
by shading the box corresponding to the letter of your choice on the answer sheet
provided.
MULTIPLE CHOICE
a. Dodecagon c.
Triacontagon
b. Icosagon d. tendicagon
2. A rectangle reservoir has the following dimensions, L=6m, W=2m, H=3m. what
is the maximum volume
of water that can be accommodated in the tank?
a. 36,000 L c. 3,600 L
b. 1,000 cu.m. d. 360 cu.m
3. What is the number of horsepower required to raise 23,100 lbs of water for
a height of 30 meters within
10 minutes?
a. 5 hp c. 7 hp
b. 6 hp d. 8 hp
4. Twenty less than four times a certain number is 8. Determine the number
a. 6 d. 3
b. 5
c. 4
6. A type of annuity were equal payments are made at the beginning of each
period.
a. 2368 c. 2278
b. 2268 d. 2378
8. A drainage pipe line 500 ft long is laid at a slope of 2%. What is the total
drop of the lower end?
a. 10 ft c. 20 ft
b. 15 ft d. 25 ft
a. 2m c. 4m
b. 3m d. 5m
11. 350 is to be divided between Jones and Smith so that jones will receive 25
more than Smith. How much
Jones received?
a. 185.50 c. 178.50
b. 187.50 d. 186.50
12. A motorboat went 70 miles in 4 hours when traveling at full speed upstream on
a river whose current
flows at the rate of 6 miles per hour. How fast can the boat travel in still
water?
13. Two coats of paint are required for an elevated water pipe line 7 inches in
diameter (outside diameter)
and 200 ft long. If a gallon of paint covers 200 sq. ft. on the first coat
and 250 sq. ft. on the second coat,
how many gallons are needed?
a. 30 gallons c. 32
gallons
b. 31 gallons d. 33
gallons
14. If the total fall of house sewer is 24 inches per 120 feet. What is the slope
per foot in sewer?
a. 0.01 c. 0.03
b. 0.02 d. 0.04
15. What is the radius of a circle the area of which is equal to that of a
rectangle whose sides are 40.50 and
17.45 inches respectively?
Page 2 of 12
a. 10 in c. 12 in
b. 11 in d. 15 in
16. What is the weight of a solid ball of brass 8 inches in diameter? Assume
specific gravity of 6.93?
a. 60 lbs c. 81 lbs
b. 64 lbs d. 67 lbs
17. Find the diameter of a circle whose area is equal to the difference between
the area of an 12.5-inch
circle and the area of a 6.5-inch circle?
a. 4.57 in c. 10.67 in
b. 6.93 in d. 14.21 in
19. How many feet can one horsepower raise a weight of 33 lbs within one hour?
a. 10 ft c. 1,000 ft
b. 100 ft d. 10,000 ft
a. 19.25% c. 18.46%
b. 19.48% d. 18.95%
21. A plumber is to install 20 meters long pipe, the length of pipe is 3.0 meters
per piece. If the plumber
have 4 pcs. of pipe available, what is the total length of pipe he will have
to install?
a. 8 c. 10
b. 12 d. 6
22. The cost of purchasing a set of bathroom fixture is P15, 000.00. If the
purchase will be made directly
with the manufacturer, a discount of 30% can be availed of. What will be the
cost of discounted fixture?
a. P 12,000.00 c. P
13,000.00
b. P 10,500.00 d. P
10,000.00
23. The age of the father is 3 times that of his son. The sum of their age is 60.
How old is the son?
a. 10 c. 15
b. 12 d. 16
24. A plumber covers a journey of 952,000 km in 7 days and 3 hours. Find his
average speed in km/s.
Page 3 of 12
a. 155 km/s c. 15.50
km/s
b. 1.55 km/s d. 1550 km/s
a. P 12,990.00 c. P 12,
980.00
b. P 12,890.00 d. P
2,770.00
26. How much work is required to lift a 50 pounds weight 100 ft vertically from
ground level?
27. A swimming pool is 5m wide, 20m long and 1.20m deep, is being filled up with
a pipe at the rate of 85
gallons per minute. How long does it take to fill the pool?
a. 6 hrs c. 7 hrs
b. 6.2 hrs d. 5 hrs
28. How many straight lines parallel to a plane passing thru a point outside the
plane can be drawn?
a. 1 c. two
b. none d. infinite
29. How many planes perpendicular to a given line can be drawn thru a point?
a. 1 c. two
b. none d. infinite
30. The formula for the change of centigrade reading to Fahrenheit reading is?
a. ºF = 5/ 9 ºC + 32 c. ºF = 9/5
ºC + 32
b. ºF = 9/5 ºC - 32 d. ºF = 5/ 9
ºC – 32
31. The radius of a circle whose area is equal to that of a rectangle whose side
are 20 meters and 30
meters respectively is:
a. 9.17 m c. 28 m
b. 13.83 m d. 27.64 m
32. Find the height of a cylinder tank which is filled with water weighing 200 kg
and its diameter of the base
is 5.82m
a. 5.5 m c. 7.5 m
b. 6.5 m d. 8.5 m
33. A total dynamic head of a certain pump installation to lift water for an
overhead water tank at certain
elevation is 65.25 feet. Neglecting friction, what is the estimated pump
pressure at the base?
Page 4 of 12
a. 190 kPa c. 200 kPa
b. 195 kPa d. 205 kPa
34. A car 15 ft. long overtakes a truck30 ft. long which is traveling at a rate
of 45 mph. How fast must the
car travel to pass the truck in 3 seconds?
a. 90 c. 91
b. 60 d. 75
a. 8 c. 9
b. 7 d. 11
36. Twenty seven coins composed of 5 centavo - coins and 25 centavo - coins have
a total value of P 4.95.
How many25 centavo - coins are there?
a. 15 c. 18
b. 20 d. 12
37. Going against the wind, the plane can travel 5/8 of the distance it can
travel in one hour if it is going with
the wind. If the plane can fly 300 mph in calm wind, what is the velocity of
the wind?
38. If the lengths of the sides of the triangle sail are 4.5m, 5.5m and 6.5m.
Find the area of the sail.
a. 10.2 c. 12.5
b. 12.2 d. 12.8
39. Two trains start from the same station and runs in opposite directions. One
runs at a uniform rate of 33
kph while the other at 35 kph. In how many hours will they be 195 km apart?
a. 4 hrs. c. 3 hrs.
b. 2 1/2 hrs. d. 3 1/2
hrs
e. .
40. A person runs 500m at an average speed of 6m/s and then the next 800m at
speed of 6m/s and then
the next 800m at an average speed of 8m/s. What is the total time required?
a. 193.3 c. 103
b. 183.3 d. 173.3
41. A plane can go 400 mph more than twice as fast as a diesel power train. If
the train can run 160 miles in
the same time that the plane can fly 1210 miles. Find the rate of the train.
Page 5 of 12
a. 75 mph c. 80 mph
b. 550 mph d. 600
mph
a. 1 c. 2
b. 0 d. 3
a. P3000 c. P2000
b. P3050 d. P1500
44. The width of a rectangle is 4/5 its length. If its perimeter is 72, what is
its area?
a. 160 c. 280
b. 250 d. 320
a. Unaligned c. Less
than 90
b. More than 90 d. 90'
46. The sum of reciprocal of two consecutive even whole numbers is 13/84. Find
the numbers.
a. 6,8 c. 0,12
b. 8,10 d. 12,14
47. You loan from a firm an amount of 100,000 with a rate of simple interest of
20 % but the interest was
deducted from the loan at the time the money was borrowed. If at the end of
one year, you have to pay
the full amount of 100,000, what is the actual rate of interest?
a. 18.8% c. 27.5%
b. 25.0% d. 30.0%
48. The paper currency issued by the Central Bank which forms part of the
country’s money supply?
a. T-bills c. Check
b. Bank note d. Coupon
49. Reduction in the level of national income and output usually accompanied by
the fall in the general price
level?
a. Devaluation c.
Inflation
b. Deflation d.
Depreciation
51. A market whereby there is only one buyer of an item for which there are no
goods substitute
a. Monopsony c. Monopoly
b. Oligopoly d.
Oligopsony
a. Perpetuity c. Annuity
due
b. Ordinary annuity d. Deferred
annuity
a. Analytic c.
Gratuitous
b. Pure d. Private
55. Direct labor cost incurred in the factory and direct material costs are the
costs of all materials that go
into production.
a. Depreciation c. Amnesty
b. Sinking fund d. Bond
59. How many distinct lines can be drawn through two points?
a. 0 c. 2
b. 1 d. an
infinite number of lines
Page 7 of 12
60. Lines are always
a. solid. c.
noncollinear.
b. finite. d. straight.
a. a plane. c. a ray.
b. a line segment. d. an arch.
a. a line c. a ray
b. a line segment d. No
determination can be made
63. The legs of a table measure 3 feet long and the top measures 4 feet long. If
the legs are connected to
the table at a right angle, then what is the distance between the bottom of
each leg and the end of the
tabletop?
a. 5 feet c. 14 feet
b. 7 feet d. 25 feet
64. Dorothy is standing directly 300 meters under a plane. She sees another plane
flying straight behind the
first. It is 500 meters away from her, and she has not moved. How far apart
are the planes from each
other?
a. 40 meters c. 4,000
meters
b. 400 meters d. 40,000
meters
65. Timmy arranges the walls of his shed on the ground. The base of the first
side measures 10 feet. The
base of the second side measures 15 feet. If the walls are at a right angle
from each other, the measure
from the end of one side to the end of the second side equals
a. 35 feet. c. 15 feet.
b. 50 feet. d. 18 feet.
66. The sides of Mary’s chalkboard consecutively measure 9 feet, 5 feet, 9 feet
and 5 feet. Without any
other information, you can determine that Mary’s chalkboard is a
a. rectangle. c.
parallelogram.
b. rhombus. d. square.
67. For any two triangles, if an angle of one triangles is congruent to an angle
of the other and if the two
sides of one triangle are proportional to two sides of the other, they are
what kind of triangles?
a. Complementary c. Similar
b. Supplementary d.
Dissimilar
Page 8 of 12
68. A figure with four sides and diagonals that bisect each angle could be a
a. rectangle. c.
parallelogram.
b. rhombus. d.
trapezoid.
69. The perimeter of Periwinkle High is 1,600 ft. It has four sides of equal
length. Each side measures
a. y=x c. x = −y
b. y=3 d. x = −4
a. 84 c. 392
b. 196 d. 168
a. 15 c. 75
b. 9 d. 225
73. One number is 6 less than 3 times another number and their sum is 62. Find
the numbers.
a. 10, 12 c. 17, 45
b. 15, 23 d. 18, 42
74. In a basketball game, the number of - scored by the Miners was equal to 20
less than twice their
opponent’s score. The total number of - scored was 127. What was the total
score of Miners?
a. 49 c. 78
b. 52 d. 67
75. What is the velocity of a car (in miles per hour) if it goes 40 miles in 35
minutes?
a. 52 miles/hr c. 71.21
miles/hr
b. 68.57 miles/hr d. 84.5
miles/hr
76. Carter sells cashews for $3.00 a pound, hazelnuts for $2.50 a pound, and
peanuts for $1.75 a pound.
How many pounds of cashews and hazelnuts should be mixed with 50 lbs of
peanuts to obtain a
mixture of 100 lbs that will sell for $2.30 a pound so that the profit or
loss is unchanged?
a. 35, 15 c. 15, 35
b. 12, 38 d. 38, 12
Page 9 of 12
77. A company manufactures its product at a cost of 50 cents per item and sells
it for 85 cents per item.
Daily overhead is $600. How many items must be manufactured each day in order
for the company to
break even?
a. 1700 c. 1730
b. 1715 d. 1745
78. Jim is 3 times as old as his cousin and the difference in their ages is 18.
How old is Jim?
a. 9 c. 27
b. 12 d. 32
79. Maria has scores of 96, 86, and 78 on three tests. What must her average
score on the next two tests
be in order for her to have an average of at least 90?
a. 89 c. 95
b. 92 d. 97
80. What are the dimensions of a rectangle whose length is 4 more than twice the
width and whose
perimeter is 3 less than 7 times the width?
a. 10, 28 c. 12, 24
b. 11, 26 d. 13, 22
81. Right triangle The shorter leg is 10 inches less than the other leg, and the
hypotenuse is 10 inches
longer than that other leg. What is the length of the hypotenuse?
a. 30 inches c. 50
inches
b. 40 inches d. 60
inches
82. Bob wants to plant a 7 foot by 10 foot garden with a uniform border of
petunias around the outside and
still have 28 square feet to plant tomatoes and roses in the middle. How wide
should the border of
petunias be?
a. 1.5 ft c. 3 ft
b. 2 ft d. 3.25 ft
83. The amount of heat required to change ice to liquid water is?
84. It is the increase in the prices for goods and services from one year to
another, thus decreasing the
purchasing power of money.
a. Discount c. Deflation
b. Inflation d. Depletion
85. The sum of the consecutive angles of a parallelogram is equal to___________
Page 10 of 12
a. 360° c. 90°
b. 180° d. 120°
86. If a triangle and a parallelogram stand on the same base and between the same
parallels, the area of
the triangle is equal to half that of the______________
a. Triangle c.
Parallelogram
b. Circle d. Square
a. Curve c.
perimeter
b. Radius d.
Diameter
88. The Pentagon is a five sided building. If each side of the Pentagon is 25
feet, what is the total area of
the bottom floor?
89. Father is aged three times more than his son Ronit. After 8 years, he would
be two and a half times of
Ronit's age. After further 8 years, how many times would he be of Ronit's
age?
a. 2 times c. " 3
times"
b. " 1 times" d. 4 times
90. Present ages of Sameer and Anand are in the ratio of 5 : 4 respectively.
Three years hence, the ratio of
their ages will become 11 : 9 respectively. What is Anand's present age in
years?
a. 24 c. 40
b. 27 d. Cannot
be determined
a. 7 c. 9
b. 8 d. 10
92. A father said to his son, "I was as old as you are at the present at the time
of your birth". If the father's
age is 38 years now, the son's age five years back was:
a. 14 years c. 33
years
b. 19 years d. 38
years
93. A right triangle with sides 3 cm, 4 cm and 5 cm is rotated the side of 3 cm
to form a cone. The volume of
the cone so formed is:
a. 12 cm3 b. 15 cm3
Page 11 of 12
c. 16 cm3 d. 20 cm3
94. In a shower, 5 cm of rain falls. The volume of water that falls on 1.5
hectares of ground is:
95. Find the area at the cross section of a pipe with the inside diameter of 14
inches and outside diameter
of 17 inches?
96. A hall is 15 m long and 12 m broad. If the sum of the areas of the floor and
the ceiling is equal to the
sum of the areas of four walls, the volume of the hall is:
a. 720 c. 1200
b. 900 d. 1800
a. 84 c. 168
b. 90 d. 336
98. A hollow iron pipe is 21 cm long and its external diameter is 8 cm. If the
thickness of the pipe is 1 cm
and iron weighs 8 g/cm3, then the weight of the pipe is:
a. 3.6 kg c. 36 kg
b. 3.696 kg d. 36.9 kg
99. A cistern 6m long and 4 m wide contains water up to a depth of 1 m 25 cm. The
total area of the wet
surface is:
a. 49 m2
b. 50 m2
c. 53.5 m2
d. 55 m2
Page 12 of 12
Mid Mock Board Exam
Physical Review Center in Iloilo City
For July 2019 Master Plumber Board Exam
PRACTICAL PROBLEM
Instructions: Select the correct answer for each of the following questions. Mark
only one answer for
each item by shading the box corresponding to the letter of your choice on the
answer sheet provided.
MULTIPLE CHOICE
5. The color used to identify the drawn copper tube for Type L is
a. White c.
Orange
b. Red d. Blue
Page 1 of 16
a. The danger of contamination of the c. The exposed
Siamese connection and
building water supply from the pipe can be
subjected to vandalism
unknown source d. The Siamese
connection can
b. The Siamese connection is expensive obstruct the
sidewalk
8. Is a steel pipe manufactured by drawing flat steel strips trough a die to form a
cylindrical shape
10. Is a drawing of piping system without regard to scale and exact location of the
fixture shown in drawing.
12. What is the minimum height of water supply pipe stub-out of water closet with
tank from finish floor?
a. 158 mm c. 200 mm
b. 114 mm d. 150 mm
13. Any vertical line of soil, waste or vent pipe extending through one or more
stories
a. Stack c. Soil
b. Chase d. Vent
14. PPE usually seen on entrance before entering the construction site stands for;
Page 2 of 16
a. Extension ladder c.
Scaffolds
b. Stepladder d. Fixed
Ladder
16. The four different types of copper pipe commonly used today are identified as
a. 1,2,3,&4 c. M, L,
K, and DWV
b. A,B,C, & D d. Red,
Blue and Wheel handle
18. Class ____ fire extinguishers are identified by the color red inside a square
a. Class A c. Class
K
b. Class B d. Class
C
19. It has a deeper and broader hook jaw housing which provided a smooth, flat
surface that is may used be
occasionally used as a hammer
20. A unique type of pipe wrench in which turning force applied is multiplied. The
principle of lever action in a
simple machine had been applied in this type of patented plumbing tools
a. Superintendent c.
Apprentice
b. Contractor d.
Journeymen
24. What is the minimum size of water supply inlet for shower stall
a. ¾ b. ½
Page 3 of 16
c. 1 d. ¼
25. What plumbing tools to be used in tightening the connections between GI pipes
and fittings?
a. 1 3/8” c. 1 ¾”
b. 1 ½” d. 1 5/8”
a. 4 c. 6
b. 2 d. 5
28. A type of wrench having a heavy sprocket chain that is slipped around a pipe
and then attached to the
wrench handled. It is used on piping work especially large size pipe metal
pipes and in areas that is not
easily accessible.
29. A tool used to tighten the nut that secure the basket to the sink
a. Pipe taps
b. Reamers
c. Deburring tools
d. Flaring
-
32. Is an adjustable cast iron box that is flash with finished grade and its capped
with removable iron cover
a. Stop cock c.
Corporation cock
b. Stop box d. None of
the above
33. Is a fitting or device that, when properly vented, provides a liquid seal to
prevent the emission of sewer
gasses.
Page 4 of 16
a. Elevated water tank c. Gravity
tank
b. Hydroelectric water tank d.
Circulating tank
36. What is the usual horizontal length that the cast iron be supported to prevent
damage at joints caused by
sagging?
38. Is a pipe that conveys rainwater from the roof to the storm drain
a. Combination c.
Sanitary pipe
b. Rainwater leader d. Waste
pipe
40. Class ____ fire extinguishers are identified by the color green inside a
triangle
a. Class K c. Class B
b. Class A d. Class C
41. In a solvent-cemented plastic piping system, most leaking joints are caused by
a worker’s failure to:
Page 5 of 16
a. Wall mounted c. Free
standing
b. Column standing d. Semi-
recessed
a. Gravity tank c.
Booster pump
b. Roof drain d. Floor
drain
49. Minor stoppage form water closet traps can be cleared with plunger, but for
more stubborn clogs, use
50. What are references in measuring the depth of a trap seal of the trap?
51. The prescribe color coding of piping under steam division of a high pressure
pipe is
a. Black c. White
b. Red d. Blue
a. Green c. White
b. Blue d. Orange
54. In large restaurant, the fixture for washing vegetable pan cauldron is the:
Page 6 of 16
55. What is that pressure that comes from the amount of air that was drag along
with friction by flowing down
the wall of the waste stack?
57. Water taken from background sources usually contain compound of Calcium and
Magnesium which
render its inconvenient for domestic used particularly?
58. The device installed above the flood level rim of plumbing fixtures to
primarily permit air from atmosphere
to prevent back siphonage of liquid from the fixture is known as:
59. As the water line for the building strike against the higher spots inside pipe
surface, energy is transferred
into the pipe causing it to move or vibrate, also produces line noise, these
phenomenon is known as:
a. Energy loss c.
Pressure loss
b. Water hammer d. Water
shocks
60. When backfilling over laid drainage pipe, a plumber must take measure to
prevent damage to the pipe.
Back fill materials should be added gradually at typical layer and must be
compacted before nest layer is
dump.
61. When pipe penetrate an exterior wall it must pass thru a sleeve. What is the
size of the sleeve thru which
to be installed for the pipe to rest?
a. Two pipe size larger c. Three
pipe size larger
b. One pipe size larger d. One
and one half pipe size larger
62. Factory waste or domestic waste is not allowed to be discharge into the drain
pipe such as what?
a. Gas pipe c.
Potable water pipe
b. Row water pipe d. Air
pipe
Page 7 of 16
64. In figure, is a graphical symbol for what kind of tee
65. When a lift check valve is not working properly, what should be done?
66. What is that plumbing devices that prevent the passage of bad odor and gasses
from the sewer system
to a building?
67. What is that device suitable for pumping sewage from the deep basement floor
into the sewer line?
68. Minor stoppage from water closet traps can be cleared with plunger, but for
more stubborn clogs, use
a. Anvils
b. Pipe vise
c. Levels
d. Pipe
a. Polyethylene extra c. X-
linked polyethylene
b. Cross linked polyethylene d. All of
the above
71. NFPA classified fires as Class ____ by flammable liquids, gasses or grease
a. Class K c. Class C
b. Class A d. Class B
72. Is a drawing showing a small part of a floor plan, elevation or section drawing
at enlarge scale
a. Detail drawing c.
Exterior elevation drawing
b. Plot plan d.
Schematic piping layout
73. What is the best water heating system to be used for both lavatory and shower?
74. What kind of pump is suited to raise water for tall buildings?
Page 8 of 16
a. Piston pump c. Booster
pump
b. Centrifugal pump d. None of
the above
75. What is the height required for vent stack thru roof above the roof if the roof
is use for some purpose like
roof deck?
a. 6 feet c. 12 feet
b. 8 feet d. 1 foot
76. What is the minimum height of water supply pipe measured from the top of
urinal?
a. 170 mm c. 200 mm
b. 180 mm d. 300 mm
77. A water closet that is easily recognized by the bulge on front and the most
noisiest of all types.
78. What is the name of the instrument which used in caulking oakum in the joints
of cast iron pipe?
a. Iron rod c. Chisel
b. Yarning iron d. Angle bar
79. What will be provided to prevent contamination from the polluted water of the
fire truck to the house water
supply system?
Page 9 of 16
85. A hack saw blade is designed to be used
87. Many copper tubing have ____ to remove the internal ridge caused by cutting the
copper tubing
88. MSDS
89. Excavated soil should not be placed any closer than _____ from the edge of a
trench.
a. 1’ c. 3’
b. 2’ d. 4’
90. The person responsible in monitoring a permit required confined space is called
a. an entrant c. an
attendant
b. a first responder d. a monitor
92. A tee with the three connections each measuring 2” is correctly ordered as:
a. 2” x 2” tee c. 2” tee
b. 2”x2”x2”tee d. none of
the above
Page 10 of 16
95. PVC pipe cannot be used for:
98. Many copper tubing have ____ to remove the internal ridge caused by cutting the
copper tube
99. Why is that it is not good practice to use a gate valve on a lawn sprinkler?
a. It is expensive
b. It is bulky
c. It will fail to close tightly
d. It is hard to operate
Page 11 of 16
Page 12 of 16
Page 13 of 16
Page 14 of 16
Page 15 of 16
Page 16 of 16