Professional Documents
Culture Documents
2. Oil tanker deck fire fighting system. And quantity of foam calculation
5. Jumping clearance in the stearing Gear system and how we can check this inside stearing Gear room
and what will happen if there is no jumping clearance?
Fun.applied: 3, 4b, 5, 6
2.Validity of IOPP
3.What is interval bw annual and i termediate survey ( he wants exact word as in SOLAS.)
5.Type of fixed extinguisher onboard gas carrier, and he asked lot n lot of questions in DCP fixed system
7.What is lat entry in ORB before reaching port.. retention quantity he didnt accept.. thn i said entry of
last transfer in engine room.. for that he firmly said "that is wrong answer".
Fun:4b
2.How to calculate power of an engine and hw u will adjust fr balancing (asusual lots of questions in
it..planimeter working, formula to find power.. spring constant wr it mentioned.. unit of spring
constant.. etc..etc..)
3.One unit high temp. Wat s ur action
4.In Ref compressor both suction and discharge pressure are same.. and rooms are getting heated up..
reason and ur action)
Fun:6
3.How to measure propeller drop. How to access the area to measure drop
5.Checks on conrod
Fun 6 :
Ism certificate
Ippo certificate
Fun 4
Eng spec
Result,
Washout
20.11.2018
Fun 3
1.container ship structure stress are maintained i said about torsional box
Fun 4
1.oil mist alarm wt ur action. With all the points he wants if engine slow down i wil stop fresh water
temperature lot of discussion for this question
Fun 6
3.rudder drop
External : Mathews
Internal : shrish
Attempt 3
Function 3
3. Which regulation says cargo hold system doesn’t require fixed firefighting system
4. How to check water ingress system and how water ingress system is working
6. What are check you will do in scba. Which regulation has says keep scba
Function 6
2. you are going to lift the cylinder liner before that What are all the checks u will made in E/R Cranes
F4
Sfoc calculation
BHP calculation
PID controller
Purifier optimisation
19 Nov
Int Shreesh
F4
Engine particulars
Fuel standards
Boiler safety valve, what info you will give to surveyor before setting safety valve
Boiler alarms and trips, if low level alarm not working in front of surveyor, what will be ur action
Expansion valve, how to order, what details you will provide to supplier
F6
There is the hole in FWG ejector line, how will you identify?
How to check trueness , ovality, gudgeon pin clearence, where to check, how to check, what is mean by
ovelness
F4 pass
Internal: shirish
Function 4b
Ac plant two room having different temperatures how to make same temperature
Main engine thrust bearing measurement
Ae surge after 50% load- turbocharger was recently overhauled, what other checks u will carry out.
- If all unit indicator cards gives different values how you will check performance if sea trail data not
available.
- Indications
- How you will fight fire, from where you will do inspection.
- For all answer he asks where fitted , what value, how fitted ,
5. What is general rule for minimum and maximum butt clearance for all engines ?
6. Refrigeration all gas leaked. How you will instruct shore technician ?
Function 4b
Ac plant two room having different temperatures how to make same temperature
Ae surge after 50% load- turbocharger was recently overhauled, what other checks u will carry out.
19 Nov
Int Shreesh
F4
Engine particulars
Fuel standards
Boiler alarms and trips, if low level alarm not working in front of surveyor, what will be ur action
Expansion valve, how to order, what details you will provide to supplier
F6
There is the hole in FWG ejector line, how will you identify?
How to check trueness , ovality, gudgeon pin clearence, where to check, how to check, what is mean by
ovelness
F4 pass
F4
Sfoc calculation
BHP calculation
PID controller
Purifier optimisation
External mr.mathews
1. How VIT is actuated in MAN B&W engines , how horizontal movement of rack is converted to vertical
movement in barrel
2. Oil mist detector alarm , steps to be followed in sequence (answer as per procedure in manual )
3. Auxiliary engine con rod complete inspection , wat to check , wer to check & how to check ( mention
about serrations , fretting , bolt checks , dye penetrant testing , spray name , oil holes in con rod to
check )
4. Auxiliary engine exhaust valve seat renewal procedure ( I told about welding old valve to seat &
hammering the seat out)
5. Main engine air cooler efficiency how to check ( air side fouling indicated by drop in air pr across the
cooler & water side fouling indicated by Drop in temp difference across the cooler)
6. Air cooler air side cooling ( ACC chemical , mixing ratio with water & how water circulated & drained )
7. Only meat room temperature not able to be maintained wat are reasons & wat u will do (main reason
is faulty TEV , if it's blocked no ref flow & so temp not maintained , I told tev setting not to be adjusted
but as a temporary measure will pour hot water on TEV )
4.08.18
External mathew
Function : 3
2.Gz ?
3.Annex 6 documents.
5. Grt ,dwt
Function: 4B.
1. Engine details.
2.sfoc
Function 5.
1.Alternator details.
3.msb safties .
Function 6
1.In Cylinder calibration report column wat u will fill and send to company regarding with values
4.main bearing cap weight according wt range chain bock u will use,see we're pulley to fix, Draw pulley
Function 3 and 5
1: all ships sailed after class4, then he asked for bulk carrier cargo hold diagram, y the shape of
cargohold like this, after looking at dia.
2. Stable ship, unstable ship... Show how we get GZ and then too many cross questions in stability.
3. Annex 1 all certificates, what all surveys?? Interval of these surveys??? Orb enteries??? Bilge
Discharge criteria??
4. For vlcc what is the firefighting system for deck, I told low expansion foam then what's the ratio and
cross questions on calculations of area and factors of multiplication, what was foam capacity of tank on
your ship- I told straight I don't remember
Decider by chowdhary: stern tube lube oil leaking into sea... Tell some temporary steps you will take to
avoid oil leakage
Result: pass in both ... And I am still not sure will see result updated first ....but thats all I am still not able
to believe i passed in both
Fun:6
External: Mathew
Fun :3
1.Iopp certificate full details with validity, renewal and intermediate survey certificate validity
5.Fixed foam Discharge area in Engine room, Fixed foam system regulations and with calculations.
Function 4&6
1. Write down name of generators on your previous ship- on man B&w- how to cut out fuel pump for
2stroke ...
3. types of fuel pump in each, Then under what circumstances you will cut out the fuel pump.. Then how
to cut out one unit of main engine and why their will be need to cut out any unit?
4. Main engine reversing procedure, wat all will happen, interlocks and safeties during reversing.
5. In Ums ship what all Me trips and slow down alarms present.
6. Scavenge fire, What will be ur action,how will u find out which unit, What all inspection after scavenge
fire.... ??
7. After scavenge fire u did unit inspection ... What all reports u will make.
8. You have to train ur 5E about boiler gauge glass blow through. Tell how you will proceed? Then after
blowing all is ok but when u open water cock water cock water is not coming? Why ... What all will u
check?
9. Prepare main bearing for survey??? What all checks and precautions observed during removal.
12. Fire in engine room ... N u r a chief engineer... How will u proceed ... ???
External: Mathew
Fun :3
1.Iopp certificate full details with validity, renewal and intermediate survey certificate validity
5.Fixed foam Discharge area in Engine room, Fixed foam system regulations and with calculations.
07 march 2018
External- Mathews
Internal- choudhary
Fun 3
Annex 6 cert
Capacity requirements,foam analysis wat all they test and their result.
EPIRB
SART
Working frequency
2. The bridge cant increase the rpm beyond Engine room set rpm. (chk that)
Internal:choudhary
External:mathew
Fun:3
4. DPA.
6. EPIRB
Internal: Mr.Barik
External:Mr.Mathew
Fun 3
1.water ingress system,how many alarms what's the regulation and alarm system fwd of collision
bulkhead i.e.in fore peak tank
2. Ur in 18yrs old vessel and psc onboard what certificates you will show to psc regarding Co2 fixed fire
fighting system,routines carried out in 2yrs 5yrs and 10yrs
4.Annex 1 documents,what is annual survey ,intermediate survey what's the regulation for both
5.What is EPIRB...How to activate and which fz it operates and what signal it will send and to where
Fun 4b
1.Ships specification..What is super long stroke and advantages over long stroke and how power to
weight ratio is increased
3.Meat room temp is dropping and reasons for it and what's the remedy as 2/e
4.Popping Up test of boiler safety valve..Procedure and what and all bypassed and blanked for doing this
test...What certificate u will show to surveyor before doing this test..
Internal: Mr.Barik
External:Mr.Mathew
Fun 3
1.water ingress system,how many alarms what's the regulation and alarm system fwd of collision
bulkhead i.e.in fore peak tank
2. Ur in 18yrs old vessel and psc onboard what certificates you will show to psc regarding Co2 fixed fire
fighting system,routines carried out in 2yrs 5yrs and 10yrs
4.Annex 1 documents,what is annual survey ,intermediate survey what's the regulation for both
5.What is EPIRB...How to activate and which fz it operates and what signal it will send and to where
Fun 4b
1.Ships specification..What is super long stroke and advantages over long stroke and how power to
weight ratio is increased
3.Meat room temp is dropping and reasons for it and what's the remedy as 2/e
4.Popping Up test of boiler safety valve..Procedure and what and all bypassed and blanked for doing this
test...What certificate u will show to surveyor before doing this test..
Fun 3
Statutory certificates
In drydock which part they make first for ship building. Draw it.
Fun 5
Diode, zener diode, transistor, thyristor explain purposes and where it used.
Function 4b and 6
Next function :
👉Plz note 👈
🤔 he expected to say what he was expecting... And do not expect what he will expect which is
unexpected.
Funtion 4b
2. Power calculation using planimeter? Planimeter working ? What are units you obtain from
planimeter?
3. SFOC calculation?
Funtion 6
1. After using DCP extinguisher how will you proceed for filling the bottle again? Step by step
procedure ?
2.ways to detect crack on ships? Explain DP test procedure ?
Expected answer from Mr mathews is risk assessment inside n outside engine room then proceed with
the rest.
Fun:4b
2. why air starting valve can't open when 30 bar air pressure acting on valve lid.
3.what are the reading u will take on piston crown and purpose.
6.use of planimeter.
1. Engine specs.
2.how to find out the performance of the engine without taking power card draw card :: with the peak
pressure values ::: if so
4.can we do individual adjustment in vit ?? VIT function and how fuel timing is advanced .
4 Ur 4e reporting unit no one starting air valve getting hot.action.(cut off the unit ) if we cut out it what
all the effects ??
5. Boiler trips :how will you demonstrate low water level trip in front of surveyor??
6.ship going to chill area : half people reporting chill comfort and half reporting chill discomfort ::: what
u will do :: unloader : how unloader works ??