This document provides the design calculations for the foundation of a 150mm thick concrete slab. Longitudinal reinforcement is required along the Y and X directions. For the Y direction, a 10mm bar spaced at 200mm with an area of 392.5mm2 is sufficient to resist the maximum moment of 6.24kNm. For the X direction, the same reinforcement is sufficient to resist the maximum moment of 11.9kNm. Shear stress calculations confirm the design is adequate to resist the applied loads.
This document provides the design calculations for the foundation of a 150mm thick concrete slab. Longitudinal reinforcement is required along the Y and X directions. For the Y direction, a 10mm bar spaced at 200mm with an area of 392.5mm2 is sufficient to resist the maximum moment of 6.24kNm. For the X direction, the same reinforcement is sufficient to resist the maximum moment of 11.9kNm. Shear stress calculations confirm the design is adequate to resist the applied loads.
This document provides the design calculations for the foundation of a 150mm thick concrete slab. Longitudinal reinforcement is required along the Y and X directions. For the Y direction, a 10mm bar spaced at 200mm with an area of 392.5mm2 is sufficient to resist the maximum moment of 6.24kNm. For the X direction, the same reinforcement is sufficient to resist the maximum moment of 11.9kNm. Shear stress calculations confirm the design is adequate to resist the applied loads.
Assume Siz of slab b = 1000 mm h = 150 mm Fck = 30 N/mm2 Fy = 448 N/mm2 Cover = 50 mm d = 95 mm
Maximum Moment = 6.24 KNm
Max bar diameter = 10 mm Spacing of bar = 200 mm Area of Steel Provided = 392.5 mm2 A-393 MESH PROVIDED K' = 0.156 K = M/ ( f cu bd2) = 0.023 No compression reinforcement required z = d{ 0.50+ (0.25-(K/0.9))1/2} = 92.50 mm 0.95 d = 90.25 mm Therefore z = 90.25 mm
Area of steel required = M/ 0.95 fy z
162.46 mm2 Area of steel provided = 392.5 mm2 A-393 MESH PROVIDED % of steel = 0.413 > 0.13 (Minimum Percentage) Hence ok
Maximum shear stress = 0.08 N/mm2 Pltae No.445 Load case.12
% Steel Provided = 0.413 Design shear stress Vu1 = 0.0800 N/mm2 Allowable shear stress = ((fcu/25)^1/3)x(0.79 x (100xAs/(bd))^1/3)/ϒm (400/d)^1/4 ) Refer BS8110-1:1997 TABLE 3.8 0.717 N/mm2 Hence ok Longitudinal bars (Along X direction) Maximum Moment = 11.9 KNm Max bar diameter = 10 mm Spacing of bar = 200 mm Area of Steel Provided = 392.5 mm2 A-393 MESH PROVIDED K' = 0.156 K = M/ ( f cu bd2) = 0.044 No compression reinforcement required z = d{ 0.50+ (0.25-(K/0.9))1/2} = 90.11 mm 0.95 d = 90.25 mm Therefore z = 90.11 mm
Area of steel required = M/ 0.95 fy z
310.30 mm2 Area of steel provided = 392.5 mm2 A-393 MESH PROVIDED % of steel = 0.413 > 0.13 (Minimum Percentage) Hence ok Maximum shear stress = 0.111 N/mm2 % Steel Provided = 0.413 Design shear stress Vu1 = 0.1110 N/mm2 Allowable shear stress = ((fcu/25)^1/3)x(0.79 x (100xAs/(bd))^1/3)/ϒm (400/d)^1/4 ) 0.717 Refer BS8110-1:1997 TABLE 3.8 Hence ok N/mm2