Professional Documents
Culture Documents
CT
Update Instructions CT003/06/P
Facelift Sensation
Remark:
Order the proper Kit for the corresponding System. See Ordering Information
© Siemens AG 2006
Chg. Ref. No.: 166142 The reproduction, transmission or use
of this document or its contents is not
Name: H.Smyk permitted without express written
authority. Offenders will be liable for
Dept.: CSPSCT damages. All rights, including rights
created by patent grant or registration
of a utility model _or_ design,_are_
reserved.
Disclaimer
The installation and service of equipment described herein is to be performed by qualified
personnel who are employed by Siemens or one of its affiliates or who are otherwise
authorized by Siemens or one of its affiliates to provide such service.
Assemblers and other persons who are not employed by or otherwise directly affiliated
with or authorized by Siemens or one of its affiliates are directed to contact one of the
local offices of Siemens or one of its affiliates before attempting installation or service pro-
cedures.
Systems/Products Affected 0
Attention: 0
➪ Order the proper Kit for the corresponding System. See Ordering Information
This update provides instructions for exchanging the gantry covers. The new covers
reflect the new corporate design.
Prerequisites 0
n.a.
Standard tools
Ordering Information 0
The following update kit has to be ordered from CSML (SAP Distribution Channel, factory
2050) :
Update Kit, Cover Sensation Open Update Kit: 88 73 692
Update Kit, Cover Sensation 40/64 Update Kit: 88 74 815
n.a.
Return of Parts 0
Work Steps 0
Sensation 40/64 0
8874559 Adapter 0
See number: 5
Remove adapter. Install new adapter. Each of the 2x3 nuts M6 has to be tighten with a
torque of 10 Nm
See number: 6
See CB-DOC Service - Gantry - Replacements of parts - Gantry front side - Gantry front
door.
Please, take the display panel (see number: 12) from the old front door and install it in the
new front door .See CB-DOC Service - Gantry - Replacements of parts - Gantry front side
- Gantry front door - Display panel.
See CB-DOC Service / Gantry / Replacements of parts / Gantry rear side / Rear funnel
➪ NOTE: SELF-LOCKING NUTS AND WASHERS MUST BE REPLACED
Final steps: 0
• The position of static light markers must be checked / respectively must be adjusted if
necessary as described in
CB-Doc / Gantry / Replacements of parts / Gantry front side / Static light markers Sensa-
tion 10/16/40/64 / Cardiac/Cardiac64
Test of function: 0
Sensation OPEN 0
8874559 Adapter 0
See number: 5
Remove Adapter. Install in new Adapter. Each of the 4 nuts M6 has to be tightened with a
torque of 10 Nm
See number: 6
See CB-DOC Service / Gantry / Replacements of parts / Gantry front side / Gantry front
door
Take the display panel (see number: 12) from the old front door and install it in the new
front door .See CB DOC Service / Gantry / Replacements of parts / Gantry front side -
Gantry front door / Display panel.
See CB DOC Service / Gantry / Replacements of parts / Gantry rear side / Rear funnel
Final steps: 0
Test of function: 0
Note: Install the short bumper first. Affix the long bumper, starting on the short bumper
side for approx. 25 cm, then fix the rest of the bumper (pull or press it).
See number:14
Remove elastic bumper on the right an left side. Affix the new green elastic bumper, it is
magnetically affixed. 0
See number:13
Remove elastic bumper on the right and left side. Clean surface e.g. with alcohol. Affix the
new green elastic bumper.(it is equipped with double sided adhesive tape).
Final Check 0
• Check the function of the horizontal and sagittal lightmarkers. If needed, please adjust
them ( see Replacement of parts)
• Perform a function check of the system according to the modifications that have been
made.
Customer Information 0
n.a.
First version
Completion Protocol 0
Remark: ....................................................................................................
....................................................................................................
NOTE After completing the update, make a copy of this page, fill it out and file
it in the corresponding System Binder/User Handbook.