Professional Documents
Culture Documents
A 112T1200 1 A
DATE
REV SHEET DESCRIPTION APPROVED
(YYYY-MM-DD) Fecha de la firma: 2014/10/07 13:47:50 GMT +02:00
A 112T1200 2 A
This is the only generator drawing that is requested by GE to be fully reviewed by the
customer and then returned to GE with inputted (or corrected) information.
A 112T1200 3 A
Generator Performance
Frequency: 60 Hz
SCR: 0.5
A 112T1200 4 A
A 112T1200 5 A
Lube oil feed connection on the Right viewed from the collector end
Lube oil drain connection on the Right viewed from the collector end
A 112T1200 6 A
Site Conditions
Site Elevation: 15 m / 49 f
Installation: Outdoor
Outdoor ambient temp: Min 2.2 deg C (36 deg F)
Max 36.1 deg C (97 deg F)
Site Voltages
A 112T1200 7 A
Cooler Details
Space Heaters
A 112T1200 8 A
Instrumentation
Temperature Sensors
Bearing Thermocouples are Type K (Chromel Alumel - Dual Element), unless noted
otherwise
Lube Oil Thermocouples are Type K (Chromel Alumel) (Dual Element) unless noted
otherwise
RTDs are 100 Ohm @ 0 C Platinum, single element, 3-wire, unless noted otherwise. (GE
RTDs are DIN standard with K=0.00385 ohms/ohm/ deg C)
Vibration Instrumentation
2 Velocity (Seismic) Probes on TE
1 Velocity (Seismic) Probes on CE
2 Single Bently-Nevada 3300 Proximity Probes, 45/45 degree locations on TE
2 Single Bently-Nevada 3300 Proximity Probes, 45/45 degree locations on CE
Liquid Detector
1 Liquid Level Detector Shipped Loose (Dual settings)
1 Liquid Level Detector in Generator Cab (Dual settings)
© COPYRIGHT 2014 General Electric Company (USA)
All rights reserved. The information herein is Proprietary and Technically Exclusive content that is solely owned by General Electric Company and/or its
affiliates. Thus, it is being provided with the explicit expectation of restricted and privileged use. All persons or legal entities receiving this information shall
be deemed by the act of its receipt have contractually agreed to make no duplications, reproductions of any nature by any means, modifications, disclosures,
or use any portion of this material; except as is expressly authorized in writing by the General Electric Company, and/or its legitimate affiliates.
A 112T1200 9 A
Notification for Customer Witness: 15 days for Official notification with 5 days confirmation
Special Tests:
Field Thermal test at running speed
A 112T1200 10 A
Other Information
Nameplate Information
GE standard nameplate information per IEC
GE English standard nameplate in Spanish per IEC
(Customer to advise if special info/language needed in Generator nameplate)
Paint
Epoxy Primer
Stator Tagging Paint
Rotor Tagging Paint
Transportation
Ship Coolers Installed
Ship with Rotor Assembled
Ship End Shields Assembled
Ship Collector Compartment/Enclosure Separate
Ship with High Voltage Bushings/Leads Installed
Ship with Generator Feet Installed (Integral)
Special Requirements
Acoustic guarantee (Near Field Avg) w/o barrier wall: 85 dBA
Will there be static start (LCI) applied to this generator? Yes
Are there any special requirements on generator cooler material? No
Is GE required to provide the ASME code stamp certificate? Yes
Are there Lift Oil Provisions for the Generator Bearings? Yes
A 112T1200 11 A
Customer Drawings
The cycle for customer drawings begin after the information for the C907 (Req Summary Sheets) is made
available to GE (i.e., phase sequence is usually the last information available).
A 112T1200 12 A
This is a compilation of “typical” data, drawings, and instructions that allow the plant
designers to understand the generator configuration and design. It also includes standard
design functional specification recommendations for piping up or applying the GE scope
equipment.