Professional Documents
Culture Documents
Design Specifications: Anchor
Design Specifications: Anchor
0
Database version
2022.6.9.13.4
Date
07/07/2022
Design Specifications
Anchor
Anchor system fischer Bolt anchor FAZ II
Anchor Bolt anchor FAZ II 16/25,
zinc plated steel
Calculated anchorage 85 mm
depth
Design Data Specification by manufacturer
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 1
C-FIX 1.109.0.0
Database version
2022.6.9.13.4
Date
07/07/2022
Input data
Design actions *⁾
# NSd VSd,x VSd,y MSd,x MSd,y MT,Sd Type of loading
kN kN kN kNm kNm kNm
1 -5.80 0.00 -20.50 1.55 0.00 0.00 Permanent-Transient/Static
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 2
C-FIX 1.109.0.0
Database version
2022.6.9.13.4
Date
07/07/2022
Steel failure
( NRd,s )
βN,s
Anchor no. % Group N° Decisive Beta
1 26.2 1 βN,s;1
2 26.7 2 βN,s;2
Pullout failure
( NRd,p )
βN,p
Anchor no. % Group N° Decisive Beta
1 41.4 1 βN,p;1
2 42.1 2 βN,p;2
( NRd,c )
Eq. (5.2)
Eq. (5.2a)
Eq. (5.2c)
Eq. (5.2d)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 3
C-FIX 1.109.0.0
Database version
2022.6.9.13.4
Date
07/07/2022
Eq. (5.2e)
βN,c
Anchor no. % Group N° Decisive Beta
1, 2 47.4 1 βN,c;1
( NRd,sp )
Eq. (5.3)
Eq. (5.2a)
Eq. (5.2c)
Eq. (5.2d)
Eq. (5.2e)
βN,sp
Anchor no. % Group N° Decisive Beta
1, 2 46.1 1 βN,sp;1
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 4
C-FIX 1.109.0.0
Database version
2022.6.9.13.4
Date
07/07/2022
( VRd,s )
βVs
Anchor no. % Group N° Decisive Beta
1 26.1 1 βVs;1
2 20.5 2 βVs;2
( VRd,cp )
Eq. (5.6)
Eq. (5.2)
Eq. (5.2a)
Eq. (5.2c)
Eq. (5.2d)
Eq. (5.2e)
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 5
C-FIX 1.109.0.0
Database version
2022.6.9.13.4
Date
07/07/2022
βV,cp
Anchor no. % Group N° Decisive Beta
1, 2 15.2 1 βV,cp;1
( VRd,c )
Eq. (5.7)
Eq. (5.7a)
Eq. (5.7b/c)
Eq. (5.7e)
Eq. (5.7f)
Eq. (10.2-5f)
Eq. (5.7h)
βV,c
Anchor no. % Group N° Decisive Beta
1, 2 74.6 1 βV,c;1
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 6
C-FIX 1.109.0.0
Database version
2022.6.9.13.4
Date
07/07/2022
Eq. (5.8b)
Eq. (5.9)
Eq. (5.8b)
Eq. (5.9)
Technical remarks
All data and information in the software is based on fischer products and common engineering knowledge. Please
check all the proof results against local valid standards and approvals.
As fischer is not the design office, the attached is no guarantee for incorrect input or assumptions. Any
recommendations have to be approved by the building-authority or project engineer. Results are valid only for
anchor system calculated in the attached. If any part of the system is changed, it will invalidate this report and new
calculations would be required.
The transmission of the anchor loads to the supports of the concrete member shall be shown for the ultimate limit state and
the serviceability limit state; for this purpose, the normal verifications shall be carried out under due consideration of the
actions introduced by the anchors. For these verifications the additional provisions given in the current design method shall
be taken into account.
As a pre-condition the anchor plate is assumed to be flat when subjected to the actions. Therefore, the plate (if present) must
be sufficiently stiff. The C-Fix anchor plate design is based on a proof of stresses and does not allow a statement about the
stiffness of the plate. The proof of the necessary stiffness is not carried out by C-Fix.
During the design process, the following hints and warnings were issued:
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 7
C-FIX 1.109.0.0
Database version
2022.6.9.13.4
Date
07/07/2022
Installation data
Anchor
Anchor system fischer Bolt anchor FAZ II
Anchor Bolt anchor FAZ II 16/25, Art.-No. 95836
zinc plated steel
Installation details
Thread diameter M 16
Drill hole diameter d0 = 16 mm
Drill hole depth h2 = 133 mm
Calculated anchorage hef = 85 mm
depth
Installation depth hnom = 103 mm
Drilling method Hammer drilling
Drill hole cleaning Only blow out by hand
No borehole cleaning required in
case of using a hollow drill bit, e.g.
fischer FHD.
Installation type Push-through installation
Annular gap Annular gap filled
Installation torque Tinst = 110.0 Nm
Socket size 24 mm
Base plate thickness t = 12 mm
Total fixing thickness tfix = 19 mm
Tfix,max tfix, max = 25 mm
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 8
C-FIX 1.109.0.0
Database version
2022.6.9.13.4
Date
07/07/2022
Attachment
Profile type Customized profile
Profile dimensions mm
Height 3
Anchor coordinates
x y
Anchor no. mm mm
1 -125 95
2 125 95
The input values and the design results should be checked against local valid standards and approvals. Please respect the disclaimer of warranty in
the license agreement of the Software.
Page 9