Professional Documents
Culture Documents
Isolated Footing 1
1.4 m 1.8 m
1.2 m
Elevation 0.4 m
X 0.9 m
Z 0.8 m 1.8 m
0.8 m
0.9 m
1.8 m
Plan
Input Values
Footing Geomtery
Column Dimensions
Pedestal
26/04/2023
Detail Design Pondasi monopole 30 m Page 2 of 13
Design Parameters
Soil Properties
Cohesion : 0.00kN/m2
Global Settings
Top Reinforcement Option : Calculate only when foundation is subjected to uplift forces
Concrete Design Option : Net Pressure(Gross Pressure - Self Weight Pressure)
Top Reinforcement Factor : 1.00
------------------------------------------------------
Design Calculations
Footing Size
26/04/2023
Detail Design Pondasi monopole 30 m Page 3 of 13
Load Combinations
Moments are about the center of footing / pile cap (does not include moments caused by lateral loads)
For the loads shown in this table, the sign convention is the same as that for JOINT LOADS in STAAD.Pro when global Y is the vertical axis.
2
Area from initial length and width, Ao = Lo X W o = 3.24 m
26/04/2023
Detail Design Pondasi monopole 30 m Page 4 of 13
Note: Amin is an initial estimation considering self-weight, axial load and moment against factored bearing capacity.
Pressures at 4 Corners
Please note that pressures values displayed in tables below are calculated after dividing by soil bearing factor
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure will be set to zero and the pressure
will be redistributed to remaining corners.
Pressure at
Pressure at top Pressure at top bottom right Pressure at
Load Case / left corner right corner corner bottom left corner
Combination (kN/m2) (kN/m2) (kN/m2) (kN/m2)
Stability Check
OTM
Load
Along X- Along Z- Required About X- About Z- Required
Case Resultant
Direction Direction FOS Direction Direction FOS
No.
26/04/2023
Detail Design Pondasi monopole 30 m Page 5 of 13
Load
Along X- Along Z- Required About X- About Z- Required
Case Resultant
Direction Direction FOS Direction Direction FOS
No.
3 N/A N/A N/A 1.50 N/A N/A 1.50
Critical Load Case And The Governing Factor Of Safety For Overturning And Sliding - X Direction
Critical Load Case And The Governing Factor Of Safety For Overturning And Sliding - Z Direction
Ultimate Pressures
The base pressures reported in this table do not include the effect of buoyancy. However, the area of footing in contact includes the effect of
buoyancy (if any).
Area of
Load Case / Pressure at Pressure at Pressure at Pressure at
footing in
Load top left top right bottom right bottom left
Contact with
Combination corner corner corner corner
soil (Au)
ID (kN/m2) (kN/m2) (kN/m2) (kN/m2) 2
(m )
Actual Area in Contact for all ultimate load cases exceeds the minimum required. Hence Safe
Maximum Corner Pressure from all ultimate load cases is less than the allowable. Hence Safe
26/04/2023
Detail Design Pondasi monopole 30 m Page 6 of 13
Shear Calculation
X 0.9 m
Z 0.17 m
0.9 m
Plan
Total Footing Depth, D = 0.40m
Calculated Effective Depth, d = D - Ccover - 1 * db = 0.34 m
For rectangular column, = Bcol / Dcol = 1.00
26/04/2023
Detail Design Pondasi monopole 30 m Page 7 of 13
X 0.9 m
0.17 m
0.9 m
0.17 m
Plan
Check that 0.75 X Vc > Vux where Vux is the shear force for the critical load cases at a distance d from the face of the column caused by bending about the X axis.
X 0.9 m
0.17 m 0.17 m
0.9 m
Plan
Check that 0.75 X Vc > Vuz where Vuz is the shear force for the critical load cases at a distance d from the face of the column caused by bending about the Z axis.
26/04/2023
Detail Design Pondasi monopole 30 m Page 8 of 13
12 - ϕ12
Calculate the flexural reinforcement along the X direction of the footing. Find the area of steel required, A, as per Section 3.8 of Reinforced Concrete Design (5th ed.) by
Salmon and Wang (Ref. 1)
The strength values of steel and concrete used in the formulae are in Mpa
26/04/2023
Detail Design Pondasi monopole 30 m Page 9 of 13
Because the number of bars is rounded up, make sure new reinforcement ratio < ρmax
Total reinforcement area, As_total = Nbar X (Area of one bar) = 1357.16 mm2
d= D - Ccover - 0.5 X (dia. of = 0.33 m
one bar)
From ACI Cl. 25.2.1, minimum req'd clear distance between bars
Cd = max (Diameter of one bar, 1.0" (25.4mm), Min. User Spacing) = 100.00mm
Provided Steel Area / Required Steel Area = 1.05
12 - ϕ12
Calculate the flexural reinforcement along the Z direction of the footing. Find the area of steel required, A, as per Section 3.8 of Reinforced Concrete Design (5th ed.) by
Salmon and Wang (Ref. 1)
The strength values of steel and concrete used in the formulae are in Mpa
26/04/2023
Detail Design Pondasi monopole 30 m Page 10 of 13
Because the number of bars is rounded up, make sure new reinforcement ratio < ρmax
Total reinforcement area, As_total = Nbar X (Area of one bar) = 1357.16 mm2
d= D - Ccover - 1.5 X (dia. of 0.33 m
=
one bar)
From ACI Cl. 25.2.1, minimum req'd clear distance between bars
Cd = max (Diameter of one bar, 1.0" (25.4mm), Min. User Spacing) = 100.00mm
Provided Steel Area / Required Steel Area = 1.05
Pedestal Design
26/04/2023
Detail Design Pondasi monopole 30 m Page 11 of 13
Shear Capacities
ϕVcX = = 396.20 kN
ϕVsX = = 213.75 kN
ϕVcZ = = 396.20 kN
ϕVsZ = = 213.75 kN
Note- Actual stirrup provided is dependent upon design requirement and bar binding and positioning. So Stirrup provided in detail drawing may vary from designed stirrup
requirements.
As total moment = 0.0, the pedestal will be designed for axial force only.
Along Z on Bottom
ϕ12 12 20.40 18.12
Face
Along X on Bottom
ϕ12 12 20.40 18.12
Face
Along Z on Top
N/A N/A N/A N/A
Face
Along X on Top
N/A N/A N/A N/A
Face
Pedestal Reinforcement
26/04/2023
Detail Design Pondasi monopole 30 m Page 12 of 13
Main Steel
ϕ16 16 2.04 51.54
(Vertical)
Transverse Steel
ϕ12 6 17.71 15.74
(Ties)
Internal Steel
ϕ12 2 10.23 9.09
(Ties)
Concrete
Soil Excavation
26/04/2023
Page 13 of 13
26/04/2023
X 0.9 m
Z 0.8 m
1.4 m 1.8 m
1.2 m
1.8 m
0.8 m
0.9 m
1.8 m
0.4 m
Plan
BOTTOM 12 - ϕ12
Dimensions (m) Reinforcement
TOP N/A
L B D AstX(T) AstZ(T) AstX(B) AstZ(B)
Foundation
0.9 m