Professional Documents
Culture Documents
OPERNS.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
PART 01 GENERAL
ENG’G
1.03 REFERENCES
SECTION 04300
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
O. Green Seal Standard GS-11 – for Commercial Flat and Non-flat Paints
Date:
By:
SECTION 04300
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
1.04 SUBMITTALS
CERT
D. A tabulation of each material used on the project that is being tracked for
recycled content. The tabulation must include the following:
DESCRIPTION
E. A tabulation of each material used on the project that is being tracked for
regional content. The following information to be included:
DATE JOB/EWO
H. Provide a listing of each indoor paint and coating used on the project.
Date:
By:
2. Product name,
3. Specific VOC data (in g/L, less water) for each product,
REVISION CERTIFICATION
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
CERT
SAUDI ARAMCO OIL COMPANY
1.06 QUALIFICATIONS
DESCRIPTION
ground.
DISCIPLINE
ENGINEER C. Each block manufactured from sulfate resisting cement shall be color
__ ________ _
coded with a green identifying mark and shall be stored separately.
DATE: ________
PROJECT PART 02 PRODUCTS
ENGINEER
____________
DATE ______ 2.01 MANUFACTURERS
CERTIFIED
A. Conesco, or equal and approved.
_ __________
DATE: ________
B. Saudi American Cold or equal and approved.
CONSTRUCTION
AGENCY
________________
C. Substitutions: Under provisions of Section 01630.
DATE: _________
B. Hollow and solid load bearing concrete blocks shall comply with ASTM C
90, Type 1, normal.
Date:
By:
C. The blocks shall be 390 x 190 x 190 mm thick, and 390 x 190 x 90 mm
OF THIS DRAWING IS COVERED, FOR ALL
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
E. Fairfaced Units
DESCRIPTION
Hollow non-load bearing block units (CMU) complying with ASTM C 129
Type 1 normal.
B. Coarse aggregates shall conform to ACI 530 and ACI 530-1 for grading
DATE JOB/EWO
C. Sand shall conform to ACI 530 and ACI 530-1, Table 5 Zones C and M.
REV.
NO.
D. Coarse aggregate and sand shall meet the same requirements for
chlorides and sulphates as the sand for mortar as specified in Section
DISCIPLINE
ENGINEER 04100.
__ ________ _
DATE: ________ 2.04 MANUFACTURE OF CONCRETE BLOCKS
PROJECT
ENGINEER
A. Blocks shall be manufactured by the use of vibration machinery and shall
____________
DATE ______ be cast on removable pallets. They shall be left on pallets to cure for ten
CERTIFIED
days during which time they shall be kept damp and shall be protected
from direct sunlight, drying winds, heavy rain and frost. No blocks shall be
_ __________ used in the works until they have attained an age of twenty-eight days.
DATE: ________
CONSTRUCTION
AGENCY
B. Blocks shall be made with Ordinary Portland Cement unless used below
________________
ground, in which case sulphate resisting cement shall be used.
DATE: _________
OPERATIONS C. The thickness of the webs and walls shall not be less than 30 mm and the
______________ volume of the cavities in the block shall not exceed 50% of the gross
DATE:_________ volume of the block.
APPROVAL/CERTIFICATION REQUIREMENTS,, CONTROL NUMBER
VERIFICATION
D. All surfaces shall be flat and rectangular and adjacent surfaces shall be at
EDSD
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
slots in the ends or sides to allow them to be fitted round the vertical
reinforcement. Samples shall be submitted to the Engineer.
CERT
B. Vertical reinforcing steel: ASTM A 615 grade 60, deformed billet uncoated
bars.
2.08 LINTELS
REV.
NO.
CONSTRUCTION
A. Samples of each type of block manufactured on the site or delivered to
AGENCY the site shall be submitted to and approved by the Engineer before use.
________________ All subsequent blocks shall be up to the standard of the approved
DATE: _________
samples.
OPERATIONS
______________
DATE:_________
B. Initially 12 blocks shall be selected by the Engineer from the first batch of
blocks manufactured or delivered, and shall be marked for future
identification as instructed by the Engineer. The blocks shall be delivered
APPROVAL/CERTIFICATION REQUIREMENTS,, CONTROL NUMBER
VERIFICATION
1. Name of Manufacturer.
OF THIS DRAWING IS COVERED, FOR ALL
SECTION 04300
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
4. Type of block.
ENG’G
A. Two sample panels 1.6 m long x 2.0 m high shall be constructed for the
Engineer's approval, including a corner and a junction, with mortar
DATE JOB/EWO
3.03 EXAMINATION
REV.
NO.
A. Verify that field conditions are acceptable and are ready to receive work.
DISCIPLINE
ENGINEER
__ ________ _
B. Verify items provided by other sections of work are properly sized and
DATE: ________ located.
PROJECT
ENGINEER
C. Verify that built-in items are in proper location, and ready for roughing into
____________
DATE ______ masonry work.
CERTIFIED
CONSTRUCTION
AGENCY
A. Direct and coordinate placement of metal anchors supplied to other
________________
sections.
DATE: _________
3.05 COURSING
APPROVAL/CERTIFICATION REQUIREMENTS,, CONTROL NUMBER
VERIFICATION
EDSD
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
1. Bond: Running.
CERT
2. Coursing: One unit and one mortar joint to equal 200 mm.
ENG’G
A. Lay solid masonry units in full bed of mortar, with full head joints,
DESCRIPTION
B. Lay hollow masonry units with face shell bedding on head and bed joints.
F. Do not shift or tap masonry units after mortar has achieved initial set.
REV.
NO.
soffits of beams or slabs shall be left clear and free from mortar and
compressible joint filler shall be packed into the joint. In fairface blockwork
Date:
By:
the exposed faces of the joint shall be sealed with a suitable non-
hardening sealant.
OF THIS DRAWING IS COVERED, FOR ALL
at every other course for the full height of the wall, unless movement
joints are required.
SECTION 04300
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
L. Mortar joints for fairface block unit wall shall be packed joints.
CERT
blockwork for the full height of the wall immediately adjacent to the
opening are to be completely filled with class C200 concrete, with
DISCIPLINE
ENGINEER maximum aggregate size 10 mm. The two filled voids are to be reinforced
__ ________ _ with 1 number 12 mm diameter mild steel bar per void, lapped 500 mm
DATE: ________
and secured with galvanized tying wire. The minimum clear distance
PROJECT between the reinforcement and the inner face of the wall of the block shall
ENGINEER
be 12 mm. Blockwork walls containing reinforcement shall be constructed
____________
DATE ______ in 400 mm lifts with the concrete surrounding the reinforcement
CERTIFIED compacted by hand tamping immediately after placing.
H. Horizontal Bond Beams: Where horizontal bond beams are required for
EDSD
lateral support they shall be located at door head height and as directed
by the Engineer.
Date:
By:
I. Lateral Support for masonry shall be in accordance with ANSI A 41.1, the
OF THIS DRAWING IS COVERED, FOR ALL
SECTION 04300
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
walls, it shall be secured to them with L-shaped galvanized steel ties 175
mm long x 25 mm wide x 3 mm thick, with a 75 mm long right angle
return at one end. The ties shall be built into the blockwork at every
second course vertically and the return pinned to the steelwork or
concrete with washered steel pins applied with a cartridge assisted hand
DESCRIPTION
be packed with compressible joint filler. Where the face of the wall is in
the same plane as the side of a beam, the angle shall be replaced with a
galvanized mild steel flat plate, 150 mm wide by 8 mm thick, to allow
fixing to the beam above the level of the main reinforcement.
REV.
NO.
______________ B. Design of reinforcement and concrete shall be able to carry all loading
DATE:_________
without deflection or cracking.
APPROVAL/CERTIFICATION REQUIREMENTS,, CONTROL NUMBER
VERIFICATION
C. Lintels, padstones etc. shall bear on to solid or filled blocks for the full
EDSD
D. In-situ cast lintels and padstones etc. shall be poured directly onto the last
whole course of blockwork.
OF THIS DRAWING IS COVERED, FOR ALL
SECTION 04300
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
A. Lay masonry units with core cells vertically aligned clear of mortar and
unobstructed.
CERT
B. Place mortar in masonry unit bed joints back 6 mm from edge of unit
ENG’G
grout spaces, bevel back and upward. Permit mortar to cure 3 days
before placing grout.
C. Reinforce masonry unit cores and cavities with reinforcement bars and
grout as indicated.
DESCRIPTION
E. Wet masonry unit surfaces in contact with grout just prior to grout
placement.
DATE JOB/EWO
CONSTRUCTION
AGENCY
3.11 TOLERANCES
________________
DATE: _________ A. Maximum Variation From Alignment of Pilasters: 6 mm.
OPERATIONS
more.
EDSD
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
A. Cut and fit for chases, pipes, conduit, sleeves, Coordinate with other
sections of work to provide correct size, shape, and location.
A. Where walls indicated on the drawings as fire resisting walls abut the
underside of concrete floor slabs or beams, the top joint shall be filled
with a ceramic fibre blanket made from kaolin or synthetic mixes of
alumina and silica or of an equivalent composition satisfying the
DATE JOB/EWO
CONSTRUCTION
AGENCY
B. Walls shall be built in the normal stretcher bond with the exception that on
________________
alternate courses purpose made half blocks shall be used to form a
DATE: _________ straight vertical joint. Control joints so formed are to be carried through all
OPERATIONS finishes. Plaster finishes shall incorporate plaster stops. Control joints in
______________ all fire resisting walls as defined on the drawings are to be formed using a
DATE:_________
ceramic fibre blanket as specified herein.
APPROVAL/CERTIFICATION REQUIREMENTS,, CONTROL NUMBER
VERIFICATION
closed cell filler board placed between the two adjoining panels of
masonry.
OF THIS DRAWING IS COVERED, FOR ALL
B. Ensure that the expansion jointing is not bridged at any point by solid
REVISION CERTIFICATION
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
3.17 CLEANING
CONSTRUCTION
AGENCY
A. Use materials with recycled content such that the sum of post-consumer
________________
recycled content plus one-half of the pre-consumer content constitutes a
DATE: _________ total of at least 20%, based on cost, of the total value of the materials in
OPERATIONS the project.
______________
DATE:_________
3.20 REGIONAL MATERIALS
APPROVAL/CERTIFICATION REQUIREMENTS,, CONTROL NUMBER
VERIFICATION
demolition.
SECTION 04300
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.
THIS DRAWING AND THE INFORMATION CONTAINED HEREIN ARE THE SOLE PROPERTY OF SAUDI ARAMCO. NO REPRODUCTION IN FULL OR IN PART SHALL BE OBTAINED FROM THIS DOCUMENT WITHOUT THE WRITTEN CONSENT OF ITS OWNER.
PMT
SAUDI ARAMCO OIL COMPANY
All adhesives and sealants used on the interior of the building (defined as inside
of the weatherproofing system and applied on-site) shall comply with the
DESCRIPTION
Paints and coatings used on the interior of the building (defined as inside of the
weatherproofing system and applied on-site) shall comply with the following
REV.
NO.
criteria:
DISCIPLINE
ENGINEER A. Architectural paints, coatings and primers applied to interior walls and
__ ________ _
ceilings: Do not exceed the VOC content limits established in Green Seal
DATE: ________ Standard GS-11, Paints, First Edition, May 20, 1993.
PROJECT – Flats: 50 g/L
ENGINEER
– Non-Flats: 150 g/L
____________
DATE ______
– Sealers: waterproofing sealers 250 g/L; sanding sealers 275 g/L; all
EDSD
SECTION 04300
CONSTRUCTION SPECIFICATIONS DWG. TYPE PLANT NO. INDEX DRAWING NO. SHT. NO. REV. NO.