Professional Documents
Culture Documents
WS41-33 DPPS PDF
WS41-33 DPPS PDF
Tensile Strength (lbs): 786,809 744,843 703,153 620,604 Upset Type: IEU Fluid Capacity w/o IPC (gal/ft): 0.89
Torsional Strength (ft-lbs): 91,278 86,332 81,430 71,754 Max Upset OD (in): 5.688 Fluid Capacity w/o IPC (bbls/ft): 0.0212
Drift Size (in): 3.875
Burst Capacity (psi): 15,507 16,836 15,950 14,177
Collapse Capacity (psi): 12,679 11,409 10,122 7,496
18
0
Note: These are OEM values that may vary with actual values due to mill tolerances, IPC tolerances, OEM rounding, and other
Notes: Body properties are calculated based on uniform OD and wall thickness. factors. Pipe is purchased at a guaranteed 95% RBW. IPC is applied to a nominal thickness of 0.009''. Pipe will have an ID of 4.72'',
Burst capacity for Nominal (100% RBW) based on 87.5% RBW per API. which is smaller than pipe purchased at 87.5%.
The technical information containted herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical
information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various
inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices,
and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
www.workstringsinternational.com 08-Sep-15
Download the Workstrings International Pipe Specification App on the App Store or Google Play
Operational Limits of Drill Pipe
Connection uGPDS55 Tool Joint OD (in) 7.000 Tool Joint ID (in) 4.000 Tool Joint Specified Minimum 130,000
Yield Strength (psi)
Pipe Body 80 % Inspection Class Pipe Body OD (in) 5.5 Wall Thickness (in) 0.361 Pipe Body Grade S-135
Combined Loading for Drill Pipe at Combined Loading for Drill Pipe at
Maximum Make-up Torque = 55,300 (ft-lbs) Minimum Make-up Torque = 39,600 (ft-lbs)
Operational Assembly Pipe Body Connection Max Operationa Assembly Pipe Body Connection
l Torque Max Tension Max Tension Max Tension
Torque Max Tension Max Tension Tension
(ft-lbs) (lbs) (lbs) (lbs) (ft-lbs) (lbs) (lbs) (lbs)
Connection
Make-up Torque Range
Make-up Torque Connection Max
(ft-lbs) Tension (lbs)
Min MUT 39,600 1,313,000
41,300 1,325,800
43,100 1,262,400
44,800 1,202,600
46,600 1,139,200
48,300 1,079,400
50,100 1,016,100
51,800 956,200
53,600 892,900
Max MUT 55,300 833,100
Note: Recommended MUT should always be used when possible. If not possible, MUT should be as close to Recommended MUT as possible.
Note: The technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be construed as a recommendation. The user is fully responsible for the accuracy and
suitability of use of the technical information. NOV Grant Prideco cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable
operating limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices, and to apply a prudent safety factor suitable for the
application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.
06-18-2015