Professional Documents
Culture Documents
HZBC-H Thiết bị đo tỉ số MBA
HZBC-H Thiết bị đo tỉ số MBA
Trong quá trình sản xuất bán thành phẩm và thành phẩm của máy biến
áp, trước khi máy biến áp mới được lắp đặt đi vào hoạt động và theo quy
trình kiểm tra phòng ngừa của Điện lực Quốc gia, các máy biến áp hoạt động
phải thường xuyên thử nghiệm đo tỷ số biến đổi điện áp. Việc sửu dụng cầu
đo truyền thống rất cồng kềnh, việc đọc không trực quan và việc thực hiện
chuyển đổi không cần thiết. Kết quả kiểm tra chỉ là tỷ số biến cảu 1 pha. Bộ
thiết HZBC-H đo tỷ số biến tự động khắc phục những thiếu sót của cầu đo
truyền thống. Thiết bị thực hiện đo lường tỷ số biến ba pha tại một thời điểm
2). Người vận hành thiết bị cần có kiến thức chung về việc sử dụng các thiết
3). Thiết bị có thể được sử dụng cả trong nhà và ngoài trời, nhưng nên tránh
sử dụng khi trời mưa, khí ăn mòn, bụi, nhiệt độ cao, nơi có ánh sáng mặt trời
trực tiếp.
5). Bảo dưỡng, chăm sóc và điều chỉnh thiết bị này nên được thực hiện bởi
nối tương ứng với các pha A, B và C, xin không làm sai.
8). Chỉ sử dụng các kẹp màu vàng và màu xanh lá cây khi thử nghiệm máy
biến áp một pha. Đừng dùng sai. Kẹp thử nghiệm không sử dụng nên được
treo.
3. Tính năng
2).Tốc độ thí nghiệm nhanh, 7 giây có thể hoàn thành thí nghiệm 3 pha
4). Hiển thi thời gian, đồng hồ vẫn chạy kể cả khi tắt nguồn.
5). Chức năng bảo vệ kết nối ngược điện áp cao và thấp.
6). Bảo vệ khi MBA bị ngắn mạch hoặc ngắn mạch vòng dây.
0.2% 2 ký tự (500~2000)
2
1). Màn hình: LCD mảng màu thật 65K, đèn nền điều chỉnh kỹ thuật số, hiển
2). Cực nối điện áp cao: vàng, xanh lục và đỏ tương ứng với máy biến áp ba
pha A, B, C.
3). Cực nối hạ áp: vàng, xanh, đỏ tương ứng với máy biến áp hạ áp ba pha
a, b, c.
4).AC 220V: Nguồn điện .
6). Reset key : Nhấn phím này để đặt lại thiết bị về trạng thái ban đầu.
7). Phím điều hướng: Phím mũi tên lên, xuống, trái và phải được sử dụng để
8).Start key: Bắt đầu đo, in kết quả kiểm tra, phím tắt.
3
Reset key : Nhấn nút này sau khi kết thúc 1 lần thí nghiệm hoặc khi bất
thường để đặt lại thiết bị
khác nhau..
: Phím điều hướng trái, mỗi menu chính chuyển động sang trái.
: Phím điều hướng phải, mỗi menu chính chuyển động sang phải..
Nút bắt đầu: Bắt đầu đo, in kết quả kiểm tra, phím tắt
Phím số: giá trị điện áp, tổ đấu dây, tỷ số biến, nhập dữ liệu
The above figure shows the boot interface, in which the main menu includes
Left and right direction keys: When the left and right direction keys are
pressed, the instrument cursor can move in the menu items, such as:
Select key: Select key when the instrument cursor is in high voltage
4
(connection mode), low voltage (connection mode), group, high voltage
(voltage value), low voltage (voltage value), voltage regulation ratio, tap
1 : The down direction key can be selected Y-D-Z when the cursor is
2 : The down direction key can be selected y-d-z when the cursor is
3 : When the cursor is in measurement mode, the down direction key can
4 : In the group, high voltage (voltage value), low voltage (voltage value),
down direction key, tap position and other options, enter the number directly,
Start button: Press the ENTER key when the power is on, then can start the
measurement. Test results can be printed after the test is finished.
The above figure shows the data query interface. The up and down direction
5
keys can scroll through the stored data, and the start key to print.
The above figure shows the interface of the host parameters. The left and
right direction keys change the options. When the cursor is in the adjustment
brightness interface, the up/down direction keys can change the contrast of
the liquid crystal. When the cursor releases the memory menu item, press the
selection key to clear the stored data. The factory setting is the internal
parameter setting of the instrument. The password input is required and the
shown in Figure 1.
6
Figure 2
tapping types, rated high voltage and low voltage value. in order to enable
caculate error value antimantically by test result, and the tap positaion at
Figure 1
according to Figure 2
7
which the tap changer is located, Once the rated data is input, the error value
of the point can be calculated automatically when testing each tapping point
and the tapping point (that is, the tapping bit is) of the point, and no need to
divided stage is 8+1 or 9, which means that the input rated position can be all,
so that for the transformer whose rated tap position is not at the middle point,
4).Turns Ratio, when the three-phase electricity is applied to the sample, the
relationship between the ratio of high voltage and low voltage. turns ratio is the
ratio of windings number of high voltage and low voltage. For high voltages
that are star-connected (whether or not they have a neutral point), for low-
voltage transformers that are delta-connected, the ratio is √3 times the value
of turns ratio. For low voltages that are star-connected (whether or not they
5). For the on-load tap-changer 19-step transformer, if 9, 10, 11 tapping is the
voltage values is not enough, you can input the high and low voltage by 10 or
100 constants.
8
1).The instrument and its supporting facilities shall be stored indoor. The
temperature shall be 0°C to 40°C, the relative humidity shall be 30% to 80%,
and the air shall not contain harmful substances that cause corrosion.
2). If the instrument is found to be faulty, please contact the company in time