Job Hazard Analysis For Electrical Conduit Installation Document No.
MLSF-0-G-JH15
CONTRACT NO.: EDC 13-228/GC113-036 PROJECT NO.: 15-8228
Control System Integration Project
DOCUMENT TITLE:
JOB HAZARD ASSESSMENT FOR TREE TRIMMING AND
PRUNING MLSF
14th Floor Salcedo Tower
169 H.V. Dela Costa St., Salcedo Village, Makati Cty
PREPARED BY:
Instrumentation and Control Specialists, Incorporated
Unit A,B,C,E & H No. 31 Mayon St., Mandaluyong City, Philippines
0 ISSUED FOR APPROVAL JGE RRM Siemens
REV. DATE DESCRIPTION PREPARED CHECKED APPD. NO.
DOC. NO.: MLPP - 0 - G - JH15 SHT. 01 OF 03 REV. 0
Instrumentation & Control Specialists, Inc. Rev. 0 Page 1 of 3
Job Hazard Analysis For Electrical Conduit Installation Document No. MLSF-0-G-JH15
JOB HAZARD ANALYSIS
Step no. Sequence of Basic Potential Hazards Corrective / Control Measure
Logical Job Steps Identify the hazards (health and safety or Determine what actions are necessary to sequence Break down job into environmental) associated with each eliminate or minimize all hazards that could steps step, examine each to find all possible lead to an accident, injury, illness or risk factors. environmental incident. 1 Consultation and Lack of consultation with all Crew to complete hazard identification task assessment stakeholders. and control form for work tasks. Lack of understanding of the Identify task hazard and risks. required tasks. Identify and implement control in Unknown hazards. accordance with the hierarchy of Incorrect personal protective controls. equipment (PPE) Identify appropriate PPE. Crew not trained or maintaining Ensure staff has appropriate training appropriate experience to perform and experience to perform task. task. Provide appropriate training prior to commencing work if required. 2 Check the work site Slips, trips and falls. Inspect site thoroughly for hazards and plan Hanging branches and other debris. Conduct hazard identification work task Poor housekeeping. assessment and control Vehicle and pedestrian movements. Identify traffic management Environmental conditions (wind, rain, requirements and assign traffic aid to heat, etc). specific work area Obtain appropriate PPE. Identify weather conditions will be suitable for required task. 3 Establish and secure Slips, trips and falls. Conduct all manual handling tasks in worksite Hanging branches and other debris. accordance with appropriate process. Poor housekeeping. Ensure all PPE is good condition, Vehicle and pedestrian movements. issued to all staff and being worn correctly. Remove or control all potential hazards within worksite. Deploy safety observer to monitor movements of vehicle and pedestrian. 4 Obtain all required Strains, sprains and crush injuries. Conduct all manual handling tasks in equipment and move Cuts, grazes and bruises. accordance with appropriate process. to work site Slip, trips and falls. Ensure all PPE is of good condition, Eye and ear damage issued to all staff and being worn Vehicle and pedestrian movements. correctly. Deploy traffic aid to monitor movements of vehicles and pedestrians. Remove or control all potential hazards within work site. 5 Inspect and start all Trains, sprains and crush injuries Conduct all manual handling tasks in equipment Cuts, grazes and bruises accordance with appropriate process. Slip, trips and fall Ensure all PPE is of good condition, Eye and ear damage issued to all staff and being worn Entanglement, crush injuries and correctly. burns Deploy traffic aid for monitoring of Machinery and equipment failure. movements of vehicle and Vehicle and pedestrian movements pedestrians. Crew not trained / experience to Complete all pre start equipment and perform required task. machinery checks. Remove any faulty equipment or machinery from service. Start and operate all equipment accordance with manufacturer’s operator’s manuals.
Instrumentation & Control Specialists, Inc. Rev. 0 Page 2 of 3
Job Hazard Analysis For Electrical Conduit Installation Document No. MLSF-0-G-JH15
JOB HAZARD ANALYSIS
Step no. Sequence of Basic Potential Hazards Corrective / Control Measure
Logical Job Steps Identify the hazards (health and safety or Determine what actions are necessary to sequence Break down job into environmental) associated with each eliminate or minimize all hazards that could steps step, examine each to find all possible lead to an accident, injury, illness or risk factors. environmental incident. Ensure staff has appropriate training and experience to perform task. 6 Climber and crew to Strains, sprains and crush injuries Induct all crew members into site engage tree with all Cuts, grazes and bruises hazards and work plan. safety equipment Slips, trips and falls. Conduct all manual handling and conduct tree Fatigue and dehydration. accordance with appropriate process. trimming and Eye injury Deploy traffic aid for monitoring of pruning using boom Entanglement, crush injuries and movements of vehicle and truck with manlift burns. pedestrians. basket Ensure all PPE is of good condition, Vehicle and pedestrian movements Personnel and objects falling from issued to all staff and being worn height. correctly Tree not dismantling in anticipated Ensure staff have appropriate training manner. and experience to perform task Unanticipated weight loads and Rest and rehydrate as required felling directions. Utilize effective methods of Bites and stinging animals and communication between all crew insects. members Tree condition of worse condition Ensure all equipment and personnel than anticipated. required at heights are properly Environmental conditions (wind, rain, secured. heat, etc). Use of full body harness with double shock absorber lanyards. Use a fall arrest harness attached to secure part of the tree Have a co-worker assist in controlling movement of falling branches Identify weather conditions will be suitable for required tasks. Ensure appropriate felling, pruning, rigging and lowering techniques are implemented. Constantly look for animals and insects within the work site. 7 Site cleanup and Strains, sprains and crush injuries Conduct all manual handling tasks in retrieval of Cuts, grazes and bruises accordance with appropriate process. equipment Slips, trips and falls. Ensure all PPE is of good conditions, Fatigue and dehydrations issued to all staff and being worn Eye injury correctly Reduce debris weight loads through size reduction. All employees to make sure work area are left in a safe condition. if required all surplus materials and rubbish to be cleaned up and put into boom truck.
Instrumentation & Control Specialists, Inc. Rev. 0 Page 3 of 3