Professional Documents
Culture Documents
worley.com
Subject: Addition in scope of work due to new scope for Flare & Dispatch area
Dear Sir,
to bring to your notice that few new items are getting added in
This is SOR of Composite contractor along
with addition and deletion of existing line-item quantities
As you may be aware that SOR for Composite contractor was issued on a fast-track basis to facilitate the early
start of civil works. At that time, Engineering for EPCM scope was in progress and flare mitigation & Dispatch
area scope were part of additional scope. We have tried to foresee and added all the line items in SOR to the
extent possible; however, few line items were left out and the same needs to be included in composite
contract as extra item. The intent of adding following items to the existing composite contractor's scope; is
to avoid lining up new contractor, which will take more time to finalise a nd may affect the overa ll completion
date.
1) Electrical items for OSBL Scope like SVL with Link Box & Without Link box, Trefoil Cable Clamps,
Junction Boxes, Modification of existing Feeder at SS 22 to power Pre-Engineered Building (PEB).
2) Additional scope of work for Flare Mitigation: Alloy steel Piping ltems, MCT Block for cable entry at
Control Room, lnstallation of specific lnstruments.
3) Addition in Scope of work at Dispatch area: Painting and lnsulation for Personal Protection.
4) Civil scope of work for electrical work in Substation 26: Civil work for Transformer, Cable trench,
Hume Pipes
h'
Worley lndia P'ivdte limited k rf
Regd Ottice: New Ere.gy House, Ramlrisl-na Mandir Road, kondivitd. Andheri (tast). MLmb. - 400059 lndia
f \ \
Telephoner +91.22.2681 2000/6133 2OOO F ax: 9L.2).2820 8295 CIN I U421OM H 1969PTC014488 [-'
/\
l*fmlsy
We would request you to provide the in-principle approvalto add the extra line items in M/s PNP scope of
Work, as part of their scope of work. Also request to de limit the SOR items in composite contractor to
facilitate payment to contractor for any increase and decrease in quantities of SOR ltem.
We foresee that the order value at completion with the addition of new quantities may not exceed the Total
Contract Value awarded to M/s PNP.
Yours faithfully,
tr-".,-*3
R&4'
3 0 rNcH IO N3140]NCH
NB 2 O INCN TO NB6OINCI]
pa.k epoxy Plr.nollc @ 150 hi(ois DFT/coal, includi.g r€pa r coai ll any foraddrtiona s.ope ot aare Mlitixation
52 1,190 -3.09% 7,294.42 57,5t4 26069253 13.03.2019 For.ddnEnals.ope of rbre Mtir 3alion
3.0 tNcH N3 7 2,140 1126 2,553.20 26069254 13.04.2019 For addinonals.ope ofFlare M gation
1 1,500 1176 3,413,43 3,319 261)69254 13 0a 2019 For additionaL scope of Flare MtlliSation
ro, oser
","" '..p.;
r're *,iiol
1 1,037 .omplete .t the time ot Pr.p3rar on of
INS U IATION TYPE : lT; TURFACE MATtilAt : (5 ; INSULATION IHICXNISS. 4! MM rNs U LAIIO N MATER lA( : Rele. Pro]e.t lnsul.tion sp.citkalion-
1,0 NCH NB 2 1,212.9S 26059253 13 03 2019 For addiriomls.ope oiFlar€ Mlii aation
TNsUIAIIONTYPE: lS AND ls/Ptl!; S(rRaACE MATEiIAI: CSIAS; ltlSULAT|ONTHI(INtSS- 95 MM tN5UtAirON MAIIRIALr ReterProie.r
2a 2)44 1126 3.09% 09310 1l03 2019 toraddltionalscope of Flar. Mtil A.tion
INsU LATION TYP t I IS AI\I D IS,,.'IIP; SURTACT MATERIAT : CS/AS J INSUTAIIOIV THICXN'SS. 13O M M INSU TATIOII MATER IAT : RE'Er PIOi'd
2,300.m 1126 2,5O9.55 2,510 26069253 13 0a 2019 For.ddirDialscooeof FlareMtiliEation
100tNcHN3 a,1a3.32 3,143 05690 260692!3 13 04.2019 For additional r.ope of Flare Mtil,ganon
INSULAIIONTYPE: ISAND ls/r:/?j SUflFACE MAIEiTAL: CS; INSUt TION SY PERSONNaIpROTtCTtON 6UAnDj TIISULAT|ON MAIIRtAt: f,€ler
ForOSBl rrea 5coper tn$ w.r not
O 75 INCH NB 7 532.59 515.35 02990 212579t2 .ompl.t..t th. t m€ oi PreprrJtion oi
\)y'
\ ,9
.9
;.r{8} SCH€DUts Of PRIC' POR INS'RUMINT
tic De-waxinB Lrnit and aliied facilitiss oI CDWU-|, proje.t
:800
Reanark For
lotal Revised f,evised Rate
S No. Item l(o Des..iption uoM [scalation Type Ot item Amount (lNR) PO Sr No Po Number Po Oate Addltlon in
atY (rNRl
INSTRUMENTAT ON
1.0 t010.00.00 PRESSURE GAUGES, ACCESSORIES
1.1 ln Carbon Stee as per Standard 44AD2800-04/1.01/0131/A3, Sht. 09 NOS 15.00 7,979 1.002 Service 115,782 00030 27251972 O.t 2021
Mitieatlon ScoDe
For Flare
1.1 ln Carbon Steelas per Standard 44AD2800-04/J.01/0131/A3, Shr. 10 NOS 3.O0 9,574 Servlce 24,123 26069258 Aug 2019
Mitisation ScoEe
1.1 ln Stainless Steelas per Standard 44AD2800-04/J .01/0731/ A3, Sht. 1.2 NOS 1.00 12,720 Service 12,720 ,n-house 26069258 Aug 2019
Mllieation Scooe
ln Carbon Steel as per Standard 44AD2800-041.O1l0131/A3, Sht. 13, 15, 16, 22 NOS 7.OO 16,223 7.OO2 Service 109,854 00050 2725191,2 oct 2021
Mitieation Scooe
ln Carbon Steel, lBR, as per Standard 44AD2800-04/1.01/0131/A3, Sht. 14 NOS 1.00 18,300 Service 18,300 26059258 Aug 2019
ln Carbon Steel as per Standard 44AD2800'0411.01/0131/A3, Sht. 18 NOS 8.00 16,223 Service 129,144 26069258 Aug 2019
MitiRatlon Scope
ln Stainless Steel as per Standard 44AD2800-04/1.01/0131/A3, Sht. 17 NOS 1.O0 27,504 Servlce 21,500 26069258 Aug 2019
Mtiqatlon ScoDe
For FIare
ln Carbon Steel, NACE as per Slandard 44AD2800 a4/).Oll0131/A3, Sht.20,24,25 NOS 9.00 19,825 Service 174,475 26069258 Aug'2019
Mitisation Scooe
ln Alloy Stcel as per Standatd 44 AD2aOO-OA/ ).A7 /0111/A3, Sht. 21 NOS 3.00 19,350 service 58,050 26069258 Aug'2019
Mitisation Scooe
ln Alloy Steel as per Standard 44AD2800-04/J.01/0131/A3, Sht. 23 NOS 2.00 19,350 Service 38,700 26069258 Aug 2019
11.6 Diffe.entlal Pressure transmitters (Flow) NOS 13.00 761 1.126 Service 74,422 0erived from 00430 26069258 Aug'2019
Mrtisrt o. Sco're
12_O t510.00.00 LOOP CHECKING
For Flare
12 74 Controlvalv€ NOS 5.00 475 1.002 2,294 o0610 27257912 Oct 2021
Mitieation ScoDe
12.75 Digital ControlValve NOS 3.00 1,150 Service 3,450 lnhouse
72.16 Batch Controller NO5 3.00 1,415 4.425
72.11 Earth Relay NOS 3.00 986 Service 7,958
12.18 Access Card Reader NO5 3.00 156 Seruice 2,268
39.0 DISMANTLING OF EXISTING INSTRUMENTS
For additional
Removal of llm t lwltch box of on / ofi valve including removal of cable glandlng and installation of new
3912 NOS 2.00 1,374 1.002 Service 2,752 Derived from 01910 21251912 od'2027 scope of Flare
limit swltch boxes (free issued by owner) on same valve and do the calibration of same.
FORX TYPE) -
For additional
44_7 lnstallation of Transmitters NOS 3.00 12,000 1.002 5ervlce 2,311 Der,ved from 00270 212519!2 Oct 2021
#=a
i'l'sott"'"\
4,,_e4
and.omm$onnsolsvL]'Gbhbo
i8b led n rubnd onl in.rudlryr,nrp.n,ionlrcm rocus*orclyadr
! Lh.r 5y!td at s.!ra €.d ,o. rll Runr . fiB rrclu&s rnn.nstion o, unk 3or * per Drawing! / 9re rn.harc in*Mtion , ,.m,M!io .f 3.3 (v xt'r sin3l. aor.
C.ble:5Rx rcx 24! sq mm.A2xrY, o/c Bbre-2R r 3Cx2(,rq. mm. A2xFy,Et4 [c,B(sloAfrponnhuousdnenr6p..iry,
,0/6.,bra 1qx3.x 13srq nn Arin, rrr,llf,13i10oAmp.o muous(uri. cpaorv) Prs shir b€ reau,rcdlorrh 5.abr€
Dr.or !*n.hrdr:rel)..15v rv
qh
\\
ry
COMPOSITE TENDER
lOCl. Haldia
Unit qtv. Revised qty Rate as Fer PO pla.ed Escaaation Dis(ount R€mark for a ddition in Qoantity
M1 MISCELLANEOUS
,ith 20mm and down srze graded crushed ,tone aggrega te!/grave ,
rveh, shapes and thickness including all nrou ds, shuttenng and
M,1.7A
give a sm
32 18,636 1.134 -7142% l 8 ,220 583,029
Providing, Laying andjointing of RCC hume pipe of NP3 class with socketand spigot ends conforming to lS:458 of
approved make, to prop€rgrade slopes and alignment,
including eanhwork in excavation in alltypes ofsoilexcept soft and hard rock for pipe trenches, pits, manholes erc.
including dewatering ofsurface/ sub surface wateras required to facilitate lowering of pipes, taking allsafety precautions,
supporting existing U/G services, shoring and shuttering if necessary, dressing ofsides,levelling, grading and.ammlng of
bottoms, cuttingthe R.C.C. pipesto required lengths, loweringthe pipes, jointing including connecUngthe pipesto
manholes and groutingthe pipes body with manhole wellusing cement mortar 1 :2 (lcement:2 Sand), testing, draining
M.1.37 1001 .3.41yo
ofwaterand c eaning of pipes aftertesting, PCC bed, sand cushion and haunEh concrete, backfilllngthe trenches with
serviceable available earth including re excavatingthe deposited soilexcavated earli€r, breakiflg €lods, laying in thickness
not exceeding 15 Cms., waterlnS, rolling and ramming by manual methods/ mechanicalcompactors to achieve 90%
laboratory dry density as per lS:2720 Part Vll, includ ing cuttine ofroadr, drains wherever required and making good the
same lncludinSsupply ofany addltiona I material if requ ired, dlsposalof surplus earth / unserviceable materialto specified
areas ,commission ing etc. complete for alldepths as per drawings, specifications and instructions ofEogineer- in - charge.
(All material lncluding cement shal be sLrpplied bycontractori
Addition or
ITEM Total revised Total with revised Cost
ITEM DESCRIPTION UOM QUANTITY Deletion to Rate as per PO placed Discount Final Rate Total Revised Cost
NO Quantity of Excess items
existing SOR
20.4.4 4.0 INCH NB MTR 5 5 0.00 2,088.98 -3.5% 2,015.87 10,079.33 0.00
20.4.5 6.0 INCH NB MTR 50 17 -33.00 2,715.67 -3.5% 2,620.62 44,550.62 -86480.62
20.4.6 8.0 INCH NB MTR 15 3 -12.00 3,237.92 -3.5% 3,124.59 9,373.77 -37495.09
20.4.7 10.0 INCH NB MTR 100 254 154.00 3,760.16 -3.5% 3,628.56 921,653.62 558797.86
20.4.8 12.0 INCH NB MTR 20 -20.00 4,073.51 0.00
20.5 INSULATION TYPE : IH, H, HC; SURFACE MATERIAL : CS/AS; INSULATION THICKNESS- 70 MM INSULATION MATERIAL : Refer Project Insulation
20.5.1 0.75 INCH NB MTR 5 5 0.00 1,201.16 -3.5% 1,159.12 5,795.61 0.00
20.5.2 1.0 INCH NB MTR 5 5 0.00 1,305.61 -3.5% 1,259.92 6,299.58 0.00
20.5.3 1.5 INCH NB MTR 5 5 0.00 1,389.17 -3.5% 1,340.55 6,702.75 0.00
20.5.4 2.0 INCH NB MTR 25 5 -20.00 1,508.24 -3.5% 1,455.45 7,277.27 -29109.09
20.5.5 3.0 INCH NB MTR 25 1 -24.00 1,932.31 -3.5% 1,864.68 1,864.68 -44752.21
20.5.6 4.0 INCH NB MTR 5 1 -4.00 2,297.88 -3.5% 2,217.45 2,217.45 -8869.81
20.5.7 6.0 INCH NB MTR 10 12 2.00 2,924.57 -3.5% 2,822.21 33,866.54 5644.42
20.5.8 8.0 INCH NB MTR 5 5 0.00 3,563.80 -3.5% 3,439.07 17,195.33 0.00
20.5.9 10.0 INCH NB MTR 15 15 0.00 4,177.96 -3.5% 4,031.73 60,475.96 0.00
20.5.10 12.0 INCH NB MTR 100 100 0.00 4,439.08 -3.5% 4,283.71 428,371.38 0.00
20.5.11 14.0 INCH NB MTR 10 10 0.00 4,924.77 -3.5% 4,752.40 47,524.02 0.00
20.6 INSULATION TYPE : IH, H, HC; SURFACE MATERIAL : SS ; INSULATION THICKNESS- 25 MM INSULATION MATERIAL : Refer Project Insulation
20.6.1 0.5 INCH NB MTR 5 5 0.00 412.57 -3.5% 398.13 1,990.67 0.00
20.6.2 0.75 INCH NB MTR 5 1 -4.00 532.69 -3.5% 514.05 514.05 -2056.18
20.6.3 1.0 INCH NB MTR 5 5 0.00 626.69 -3.5% 604.76 3,023.80 0.00
20.6.4 1.5 INCH NB MTR 5 5 0.00 811.57 -3.5% 783.16 3,915.82 0.00
20.6.5 2.0 INCH NB MTR 15 15 0.00 940.04 -3.5% 907.14 13,607.09 0.00
20.6.6 3.0 INCH NB MTR 10 6 -4.00 1,211.61 -3.5% 1,169.20 7,015.21 -4676.81
20.6.7 4.0 INCH NB MTR 5 5 0.00 1,441.40 -3.5% 1,390.95 6,954.74 0.00
20.6.8 6.0 INCH NB MTR 5 5 0.00 1,880.08 -3.5% 1,814.28 9,071.39 0.00
20.6.9 8.0 INCH NB MTR 5 5 0.00 2,245.65 -3.5% 2,167.06 10,835.28 0.00
20.6.10 10.0 INCH NB MTR 5 1 -4.00 2,611.22 -3.5% 2,519.83 2,519.83 -10079.33
20.6.11 12.0 INCH NB MTR 5 5 0.00 3,133.47 -3.5% 3,023.80 15,118.99 0.00
20.7 INSULATION TYPE : IT; SURFACE MATERIAL : CS ; INSULATION THICKNESS- 25 MM INSULATION MATERIAL : Refer Project Insulation specification-
20.7.1 0.75 INCH NB MTR 100 1 -99.00 470.02 -3.5% 453.57 453.57 -44903.40
20.7.1 1.0 INCH NB MTR 100 100 0.00 626.69 -3.5% 604.76 60,475.96 0.00
20.7.2 1.5 INCH NB MTR 100 100 0.00 746.81 -3.5% 720.67 72,067.18 0.00
20.7.3 2.0 INCH NB MTR 250 250 0.00 846.04 -3.5% 816.43 204,106.36 0.00
20.7.4 3.0 INCH NB MTR 600 1 -599.00 1,044.49 -3.5% 1,007.93 1,007.93 -603751.66
20.7.5 4.0 INCH NB MTR 1,200 1 -1199.00 1,253.39 -3.5% 1,209.52 1,209.52 -1450213.50
20.7.6 6.0 INCH NB MTR 2,000 70 -1930.00 1,775.63 -3.5% 1,713.49 119,943.99 -3307027.03
20.7.7 8.0 INCH NB MTR 1,600 15 -1585.00 2,088.98 -3.5% 2,015.87 30,237.98 -3195146.51
20.7.8 10.0 INCH NB MTR 800 800 0.00 2,297.88 -3.5% 2,217.45 1,773,961.47 0.00
20.7.9 12.0 INCH NB MTR 2,200 1,200 -1000.00 2,924.57 -3.5% 2,822.21 3,386,653.71 -2822211.42
20.7.10 14.0 INCH NB MTR 1,800 1,800 0.00 3,412.00 -3.5% 3,292.58 5,926,643.99 0.00
20.7.11 16.0 INCH NB MTR 250 250 0.00 3,899.43 -3.5% 3,762.95 940,737.14 0.00
20.7.12 18.0 INCH NB MTR 1,100 1,000 -100.00 4,386.86 -3.5% 4,233.32 4,233,317.14 -423331.71
20.7.13 20.0 INCH NB MTR 900 900 0.00 4,874.29 -3.5% 4,703.69 4,233,317.14 0.00
20.8 INSULATION TYPE : IS AND IS/PP/P; SURFACE MATERIAL : CS ; INSULATION THICKNESS- 25 MM INSULATION MATERIAL : Refer Project Insulation
20.8.1 0.5 INCH NB MTR 5 5 0.00 443.91 -3.5% 428.37 2,141.86 0.00
20.8.2 0.75 INCH NB MTR 5 5 0.00 574.47 -3.5% 554.36 2,771.81 0.00
20.8.3 1.0 INCH NB MTR 5 5 0.00 652.81 -3.5% 629.96 3,149.79 0.00
20.8.4 1.5 INCH NB MTR 5 5 0.00 731.14 -3.5% 705.55 3,527.76 0.00
20.8.5 2.0 INCH NB MTR 5 5 0.00 835.59 -3.5% 806.35 4,031.73 0.00
20.8.6 3.0 INCH NB MTR 10 10 0.00 1,044.49 -3.5% 1,007.93 10,079.33 0.00
20.8.7 4.0 INCH NB MTR 10 10 0.00 1,305.61 -3.5% 1,259.92 12,599.16 0.00
20.8.8 6.0 INCH NB MTR 5 5 0.00 1,671.18 -3.5% 1,612.69 8,063.46 0.00
20.8.9 8.0 INCH NB MTR 5 5 0.00 2,088.98 -3.5% 2,015.87 10,079.33 0.00
20.8.10 10.0 INCH NB MTR 5 5 0.00 2,496.33 -3.5% 2,408.96 12,044.80 0.00
20.8.11 12.0 INCH NB MTR 5 5 0.00 2,715.67 -3.5% 2,620.62 13,103.12 0.00
20.9 INSULATION TYPE : IE; SURFACE MATERIAL : CS ; INSULATION THICKNESS- 25 MM INSULATION MATERIAL : Refer Project Insulation specification-
20.9.1 0.5 INCH NB MTR 5 5 0.00 449.13 -3.5% 433.41 2,167.06 0.00
20.9.2 0.75 INCH NB MTR 5 2 -3.00 564.02 -3.5% 544.28 1,088.57 -1632.85
20.9.3 1.0 INCH NB MTR 5 52 47.00 678.92 -3.5% 655.16 34,068.12 30792.34
20.9.4 1.5 INCH NB MTR 5 5 0.00 835.59 -3.5% 806.35 4,031.73 0.00
20.9.5 2.0 INCH NB MTR 10 25 15.00 1,044.49 -3.5% 1,007.93 25,198.32 15118.99
20.9.6 3.0 INCH NB MTR 5 5 0.00 1,305.61 -3.5% 1,259.92 6,299.58 0.00
20.9.7 4.0 INCH NB MTR 2,667 10 -2657.00 1,556.29 -3.5% 1,501.82 15,018.20 -3990334.81
20.9.8 6.0 INCH NB MTR 5,782 7000 1218.00 1,880.08 -3.5% 1,814.28 12,699,951.41 2209791.55
20.9.9 8.0 INCH NB MTR 1,355 250 -1105.00 2,313.54 -3.5% 2,232.57 558,142.71 -2466990.76
20.9.10 10.0 INCH NB MTR 615 1600 985.00 2,715.67 -3.5% 2,620.62 4,192,999.83 2581315.52
20.9.11 12.0 INCH NB MTR 15 15 0.00 2,924.57 -3.5% 2,822.21 42,333.17 0.00
21 ERECTION OF ROTARY EQUIPMENT
21.1 All type of Pumps with Drivers and all accessories MT 35 35 0.00 35,956.44 -3.5% 34,697.96 1,214,428.76 0.00
22 ERECTION OF PACKAGE EQUIPMENT
22.1 Loading Arms MT 2 2 0.00 38,828.70 -3.5% 37,469.70 74,939.39 0.00
Addition or
ITEM Total revised Total with revised Cost
ITEM DESCRIPTION UOM QUANTITY Deletion to Rate as per PO placed Discount Final Rate Total Revised Cost
NO Quantity of Excess items
existing SOR
23.1.2 SS Piping INCH MTR 150 150 0.00 606.37 -3.5% 585.14 87,771.48 0.00
29.12 Safety Supervisor/ HSE engineer - minimum 5 year experience required MAN DAY 60 60 0.00 2,154.72 -3.5% 2,079.31 124,758.31 0.00
29.13 Valve Mechanic MAN DAY 7 7 0.00 1,337.91 -3.5% 1,291.08 9,037.55 0.00
CHEMICAL CLEANING/PASSIVATION WORK:
30
Degreasing and chemical cleaning inclusive of rinsing, preservation, neutralization, drying etc. for Piping, equipment as per specification and as per
30.1 Degreasing/Chemical Cleaning/Passivation of Piping INCH MTR 3,000 3,000 0.00 123.68 -3.5% 119.35 358,055.20 0.00
31 HYDROLYZING OF PIPELINE:-
Carry out cleaning of inside surface of pipelines by water jetting/Hydrolyzing including mobilization and demobilization of all required
31.1
machineries/high pressure pumps/nozzle, hose, manpower etc. to complete the work in all respects to the satisfaction of engineer in charge.
31.1.1 0.75 INCH NB MTR 10 10 0.00 416.29 -3.5% 401.72 4,017.22 0.00
31.1.2 1 .0 INCH NB MTR 10 10 0.00 494.72 -3.5% 477.41 4,774.07 0.00
31.1.3 1.5 INCH NB MTR 10 10 0.00 742.08 -3.5% 716.11 7,161.10 0.00
31.1.4 2.0 INCH NB MTR 10 10 0.00 989.44 -3.5% 954.81 9,548.14 0.00
31.1.5 3.0 INCH NB MTR 10 10 0.00 1,301.59 -3.5% 1,256.03 12,560.35 0.00
31.1.6 4.0 INCH NB MTR 10 10 0.00 1,301.59 -3.5% 1,256.03 12,560.35 0.00
31.1.7 6.0 INCH NB MTR 10 10 0.00 1,301.59 -3.5% 1,256.03 12,560.35 0.00
31.1.8 8.0 INCH NB MTR 10 10 0.00 1,527.75 -3.5% 1,474.28 14,742.78 0.00
31.1.9 10.0 INCH NB MTR 10 10 0.00 1,841.07 -3.5% 1,776.64 17,766.36 0.00
31.1.10 12.0 INCH NB MTR 10 10 0.00 1,841.07 -3.5% 1,776.64 17,766.36 0.00
31.1.11 14 INCH NB MTR 10 10 0.00 2,019.48 -3.5% 1,948.80 19,487.96 0.00
31.1.12 16 INCH NB MTR 10 10 0.00 2,187.93 -3.5% 2,111.36 21,113.57 0.00
31.1.13 18.0 INCH NB MTR 10 10 0.00 2,348.15 -3.5% 2,265.96 22,659.65 0.00
31.1.14 20.0 INCH NB MTR 10 10 0.00 2,501.38 -3.5% 2,413.84 24,138.35 0.00
31.1.15 24.0 INCH NB MTR 10 10 0.00 2,790.55 -3.5% 2,692.88 26,928.76 0.00
32 SCAFFOLDING WORKS
Providing and installing steel scaffoldings at various locations and elevations and making working platforms & approach ladder as per the project
32.1
safety specifications and as per IS 2750-1964. For detailed work Item description refer below.
32.1.1. From Ground level to 20 mtr level SQM 200 200 0.00 184.51 -3.5% 178.05 35,610.94 0.00
32.1.2 From 20 mtr level unto 40 mtr level SQM 200 200 0.00 461.29 -3.5% 445.15 89,029.50 0.00
32.1.3 Volumetric Scaffolding for all height (Measurement should be as per Floor area X Height) CUM 400 6,000 5600.00 184.51 -3.5% 178.05 1,068,328.22 997106.34
GALVANISED PIPING (ABOVE GROUND)
33
33.1 Supply and Laying of galvanized pipes & fittings confirming to IS 1239 including supply of consumables, all tools & tackles, Victaulic coupling
33.1.1 0.75 INCH NB MTR 10 10 0.00 833.89 -3.5% 804.71 8,047.06 0.00
33.1.2 1 .0 INCH NB MTR 10 10 0.00 833.89 -3.5% 804.71 8,047.06 0.00
33.1.3 1.5 INCH NB MTR 10 10 0.00 1,251.42 -3.5% 1,207.62 12,076.19 0.00
33.1.4 2.0 INCH NB MTR 10 10 0.00 1,446.26 -3.5% 1,395.64 13,956.45 0.00
33.1.5 3.0 INCH NB MTR 10 10 0.00 2,168.82 -3.5% 2,092.91 20,929.08 0.00
33.1.6 4.0 INCH NB MTR 10 10 0.00 2,887.89 -3.5% 2,786.81 27,868.13 0.00
33.1.7 6.0 INCH NB MTR 10 10 0.00 4,331.83 -3.5% 4,180.22 41,802.19 0.00
DISMANTLING OF ERECTED VALVES (ABOVE GROUND):
34
Dismantling of all types and ratings of valves by unbolting, cutting etc. as required, cleaning by flushing with water/air etc. as required, including
34.1 Flanged / Welded Valves/Strainers/Bellows (Except TSV/PSV & Control Valve) of all ratings
34.1.1 0.75 INCH NB NO 50 50 0.00 401.59 -3.5% 387.54 19,376.93 0.00
34.1.2 1 .0 INCH NB NO 40 40 0.00 477.26 -3.5% 460.55 18,422.06 0.00
34.1.3 1.5 INCH NB NO 15 15 0.00 608.70 -3.5% 587.40 8,810.98 0.00
34.1.4 2.0 INCH NB NO 40 40 0.00 723.38 -3.5% 698.07 27,922.62 0.00
34.1.5 3.0 INCH NB NO 10 10 0.00 1,063.80 -3.5% 1,026.57 10,265.67 0.00
34.1.6 4.0 INCH NB NO 30 30 0.00 1,489.32 -3.5% 1,437.19 43,115.81 0.00
34.1.7 6.0 INCH NB NO 20 20 0.00 2,127.60 -3.5% 2,053.13 41,062.68 0.00
34.1.8 8.0 INCH NB NO 10 10 0.00 2,872.26 -3.5% 2,771.73 27,717.31 0.00
34.1.9 10.0 INCH NB NO 12 12 0.00 3,829.68 -3.5% 3,695.64 44,347.69 0.00
34.1.10 12.0 INCH NB NO 8 8 0.00 4,255.20 -3.5% 4,106.27 32,850.14 0.00
34.1.11 14 INCH NB NO 8 8 0.00 4,667.54 -3.5% 4,504.18 36,033.41 0.00
34.1.12 16 INCH NB NO 10 10 0.00 5,056.89 -3.5% 4,879.90 48,798.96 0.00
34.1.13 18.0 INCH NB NO 4 4 0.00 5,427.19 -3.5% 5,237.23 20,948.94 0.00
34.1.14 20.0 INCH NB NO 4 4 0.00 5,781.35 -3.5% 5,579.00 22,316.01 0.00
34.1.15 24.0 INCH NB NO 4 4 0.00 6,449.68 -3.5% 6,223.94 24,895.75 0.00
35 DISMANTLING WORKS
Dismantling of erected steel structures, ladders, platforms, handrails, etc. to facilitate equipment and piping erection and shifting to the designated
35.1 MT 10 10 0.00 19,121.00 -3.5% 18,451.77 184,517.65 0.00
location with in the refinery as per instructions of Engineer-in Charge.
36 Dismantling and removal of existing reusable/redundant equipment to facilitate erection of new equipment at all elevation and locations.
The work item covers the following activities:
36.1 MT 15 15 0.00 27,000.00 -3.5% 26,055.00 390,825.00 0.00
Dismantling and removal of existing reusable/redundant (Rotary ad Static) equipment to facilitate erection of new equipment at all elevation and
37 Modification of Piping/additional works :-
37.1 Carbon Steel Piping-All grades (IBR/Non IBR)
37.2 Flame Cutting INCH DIA 300 300 0.00 145.74 -3.5% 140.64 42,191.90 0.00
37.3 Hack saw cutting INCH DIA 250 250 0.00 164.89 -3.5% 159.12 39,779.47 0.00
37.4 Grinding/Edge preparations/Beveling INCH DIA 200 200 0.00 178.72 -3.5% 172.46 34,492.65 0.00
37.5 Fit Up /Welding INCH MTR 200 200 0.00 499.99 -3.5% 482.49 96,497.30 0.00
37.6 Erection INCH MTR 250 250 0.00 202.12 -3.5% 195.05 48,761.93 0.00
37.7 Hydro testing/Flushing/Reinstatement/documentation INCH MTR 250 250 0.00 143.61 -3.5% 138.59 34,646.64 0.00
38 ERECTION OF SP ITEM
38.1 Scope of activities are as follows:
38.1.1 1/2 Inch NB Thermodynamic Steam Trap NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
Addition or
ITEM Total revised Total with revised Cost
ITEM DESCRIPTION UOM QUANTITY Deletion to Rate as per PO placed Discount Final Rate Total Revised Cost
NO Quantity of Excess items
existing SOR
38.1.2 6 Inch NB T- Type Strainer NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
38.1.2 8 Inch NB T- Type Strainer NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
38.1.3 10 Inch NB T- Type Strainer NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
38.1.4 12 Inch NB T- Type Strainer NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
38.1.5 14 Inch NB T- Type Strainer NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
38.1.6 16 Inch NB T- Type Strainer NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
38.1.7 18 Inch NB T- Type Strainer NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
38.1.8 20 Inch NB T- Type Strainer NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
38.1.9 2 Inch NB Mettalic Hose NO 1 1 0.00 170.21 -3.5% 164.25 164.25 0.00
IOCL, Haldia
SCHEDULE OF PRICE
Catalytic De-waxing Unit and allied facilities of CDWU-II Project
FOR ELECTRICAL
44AD2800 ELECTRICAL
Addition or
Item No. Description Qty. Total revised QTY Rate (INR) Discount Final rate Total Revised Cost Total Cost of Excess Items
deletion
1 DISMANTLING AND DISCONNECTION OF ELECTRICAL EQUIPMENT -
Disconnection and Dismantling of following existing equipment (motor, LCS, lighting fixture, power & control cables etc.), including
removal of termination, transporting to IOCL's Haldia refinery store, all labour and materials, as per specifications of this tender and as per
directions of Engineer-in-Charge. (Refer Note 7)
1.1 Disconnection of following existing motors at field end (power, control and space heater cables, RTD / BTD/ Thermistor cables,
Earthing conductors), including all labour and materials, as per specifications of this tender and as per directions of Engineer-in-Charge.
Existing 415V MV motors. - 7 7 0 7,021.1 -3.50% 6,775 47,427 0.00
Existing 6.6kV HV motors. - 2 2 0 10,850.8 -3.50% 10,471 20,942 0.00
1.2 Disconnection, dismantling of existing industrial / flameproof local control stations at field end 4 4 0 1,276.6 -3.50% 1,232 4,928 0.00
The dismantling includes disconnecting the control cable terminations, earthing conductors, canopy, structural steel members etc.
1.3 dismantling of heat shrinkable end termination kits for XLPE insulated HT power cables 6.6kV (UE) grade
of following sizes including dismantling of Al / Cu/ bi-metallic lugs, gland plates,Clamps,removal of earthing of armour,etc in 6.6kV HV
switchgear located in existing substation with all labour and materials as per the specification of this tender. Scope includes returning of removed
termination kits to IOCL's Haldia refinery store / Warehouse as applicable as per directions of Engineer-in-Charge. (Refer Note 8).
6.6kV (UE) Grade Termination Kits
3C x 240 sq. mm 2 2 0 1,223.4 -3.50% 1,181 2,361 0.00
1.4 Dismantling of end terminations of power/control cables at switchgear/PMCC/PCC/MCC side for following cables and removal
of leads including dismantling of cable glands and lugs, from switchboards/panels/misc. electrical equipment, including all labour and
materials, as per specifications of this tender and as per directions of Engineer-in-Charge. -
Cables with OD upto 20 mm. - 8 8 0 72.3 -3.50% 70 558 0.00
Cables with OD above 20 mm but upto 30 mm. - 8 8 0 106.4 -3.50% 103 821 0.00
Cables with OD above 30 mm but upto 40 mm. - 1 1 0 144.7 -3.50% 140 140 0.00
Cables with OD above 40 mm but upto 50 mm. - 1 1 0 223.4 -3.50% 216 216 0.00
Cables with OD above 50 mm but upto 60 mm. - 16 16 0 335.1 -3.50% 323 5,174 0.00
Cables with OD above 60 mm but upto 80 mm. - 1 1 0 500.0 -3.50% 482 482 0.00
1.5 Removal of Cables from existing switchboards/panels/misc. electrical equipment in Existing substation/ Existing Main control room/
Existing rack room etc. ISBL Areas and returning filled up drums to IOCL's Haldia refinery store / Warehouse
as applicable as per directions of Engineer-in-Charge. (Refer Note 8). Scope includes Retrieval/ Removal of cables laid in buried/ RCC
trenches/ cable-trays / ground/ installed at heights and recoiling (in neat coils/ drums) removal of twisting / bends, tagging with
cable-type/ length indications and shifting to designated locations (cable yard/ other sites) including work-at-height arrangement &
supply of manpower/crane/truck as per the directions of Engineer-in-charge
1.5.1 6.6kV (UE) Grade cables
Cables with OD upto 20 mm. - 100 100 0 23.4 -3.50% 23 2,258 0.00
Cables with OD above 20 mm but upto 30 mm. - 100 100 0 26.6 -3.50% 26 2,566 0.00
Cables with OD above 30 mm but upto 40 mm. - 100 100 0 40.4 -3.50% 39 3,901 0.00
Cables with OD above 40 mm but upto 50 mm. - 100 100 0 50.0 -3.50% 48 4,825 0.00
Cables with OD above 50 mm but upto 60 mm. - 100 100 0 55.8 -3.50%
Cables with OD above 60 mm but upto 80 mm. - 1000 1000 0 58.5 -3.50%
1.5.2 650 / 1100 V Grade cables
Cables with OD upto 20 mm. - 4200 4200 0 23.4 -3.50% 23 94,855 0.00
Cables with OD above 20 mm but upto 30 mm. - 4000 4000 0 26.6 -3.50% 26 102,657 0.00
Cables with OD above 30 mm but upto 40 mm. - 100 100 0 40.4 -3.50% 39 3,901 0.00
Cables with OD above 40 mm but upto 50 mm. - 100 100 0 50.0 -3.50% 48 4,825 0.00
Cables with OD above 50 mm but upto 60 mm. - 8000 8000 0 55.8 -3.50% 54 430,610 0.00
Cables with OD above 60 mm but upto 80 mm. - 100 100 0 58.5 -3.50% 56 5,646 0.00
1.6 Disconnection, dismantling of existing industrial / flameproof lighting fixtures at field end, 10 0 -10 4,500.0 -3.50% 4,343 0.00 -43425.00
1.7 Disconnection, dismantling of existing industrial / flameproof convenience sockets at field end 1 0 -1 4,500.0 -3.50% 4,343 0.00 -4342.50
The dismantling includes disconnecting the power cable terminations, earthing conductors, poles/structural steel members etc.
1.8 Disconnection, dismantling of existing industrial / flameproof welding sockets at field end 1 0 -1 4,500.0 -3.50% 4,343 0.00 -4342.50
The dismantling includes disconnecting the power cable terminations, earthing conductors, poles/structural steel members etc.
2 Miscellaneous panel
2.1 Miscellaneous panel installation
Installation, testing and commissioning of Control panels, misc. electrical panels etc., (to be installed in substation)
including transportation from IOCL's store/yard to site at the place of installation, unpacking, assembly, including mounting and wiring of
loose parts supplied by equipment vendor, interconnection of shipping sections and requisite inter-panel wiring between shipping sections,
including supply of all wiring materials, installation on Floor channels / Angles/ frame work, foundations or fixing to wall or steel structures,
aligning, levelling, grouting, testing and calibration of relays and meters, Relay settings etc., including all labour and materials, as per
approved drawings, specifications of this tender and directions of Engineer-in-Charge. -
2.1.1 Weight of the Unit upto 100 kg. - 1 0 -1 3,319.1 -3.50% 3,203 0.00 -3202.89
2.1.2 Weight of the Unit from 101 upto 500 kg. - 1 0 -1 5,521.1 -3.50% 5,328 0.00 -5327.88
2.1.3 Weight of the Unit from 501 upto 1000 kg. - 1 0 -1 11,047.6 -3.50% 10,661 0.00 -10660.90
2.1.4 Weight of the Unit from 1001 upto 1500 kg. - 1 0 -1 15,744.2 -3.50% 15,193 0.00 -15193.19
2.1.5 Weight of unit above 1500 kg 1 0 -1 19,680.3 -3.50% 18,991 0.00 -18991.49
Equipment considered in above list are as follows:
a 415 V Electrical Heat Trace panel to be installed in Substation 26 at first floor. 1 0 -1 Rate Considered above 0.00
(Approx. Dimension - 800 x 600 x 2225)
2.2 Miscellaneous panel Supply
Supply, installation, testing and commissioning of SVL/Cable box for 33kV system, misc. electrical panels etc.,
(to be installed in substation) including transportation from IOCL's store/yard to site at the place of installation, unpacking, assembly,
including mounting and wiring of loose parts supplied by equipment vendor, interconnection of shipping sections and requisite inter-panel
Addition or
Item No. Description Qty. Total revised QTY Rate (INR) Discount Final rate Total Revised Cost Total Cost of Excess Items
deletion
wiring between shipping sections, including supply of all wiring materials, installation on Floor channels / Angles/ frame work, foundations
or fixing to wall or steel structures, aligning, levelling, grouting, testing and calibration of relays and meters, Relay settings etc., including
all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. -
2.2.1 Weight of the Unit upto 100 kg. -
2.2.2 Weight of the Unit from 101 upto 500 kg. - 28 28 0 Rate Considered in Sr No 2.2.5 a 0.00
2.2.3 Weight of the Unit from 501 upto 1000 kg. -
2.2.4 Weight of the Unit from 1001 upto 1500 kg. -
2.2.5 Weight of unit above 1500 kg
33kV power cable Link Boxes/SVL of suitable rating & design for cross-bonding of armour & metallic screen of each cable at each end as well as at each joint location.
a 28 6 -22 60,000.0 -3.50% 57,900 347400.00 -1273800.00
Additionally single core cable for armoured earthing with Link box/SVL to be considered.
(Approx. Dimension - 800 x 600 x 800)
4 JUNCTION BOXES
Supply, installation, cable termination, connection, testing and commissioning of following types of
FLP and WP junction boxes, suitable for gas group IIA/IIB, IIC, temperature class T3/ T4, as per details given elsewhere in tender
document, including suitably sized busbars with current rating equal to the largest cable current rating, glands, lugs, earthing
terminals, canopy etc., including all labours and materials, as per approved drawings, specifications of this tender and directions of
Engineer-in-Charge. -
4.1 FLP Power JBs:
4.1.1 Incoming Cable : 1R X 3C X 6 sq. mm. 2XWY, O/G cable:-1R X 3C X 4 sq. mm. 2XWY, Exd, IIC, T3 1 0 -1 8,564.8 -3.50% 8,265 0.00 -8265.05
4.1.2 Incoming Cable : 1R X 3C X 10 sq. mm. 2XWY, O/G cable:-1R X 3C X 6 sq. mm. 2XWY, Exd, IIC, T3 1 0 -1 8,564.8 -3.50% 8,265 0.00 -8265.05
4.1.3 Incoming Cable : 1R X 3C X 16 sq. mm. A2XFY, O/G cable:-1R X 3C X 10 sq. mm. 2XWY, Exd, IIC, T3 1 0 -1 8,564.8 -3.50% 8,265 0.00 -8265.05
4.1.4 Incoming Cable : 1R X 3C X 25 sq. mm. A2XFY, O/G cable:-1R X 3C X 16 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 8,878.2 -3.50% 8,567 0.00 -8567.43
4.1.5 Incoming Cable : 1R X 3C X 35 sq. mm. A2XFY, O/G cable:-1R X 3C X 25 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 8,878.2 -3.50% 8,567 0.00 -8567.43
4.1.6 Incoming Cable : 1R X 3C X 50 sq. mm. A2XFY, O/G cable:-1R X 3C X 35 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 8,878.2 -3.50% 8,567 0.00 -8567.43
4.1.7 Incoming Cable : 1R X 3C X 70 sq. mm. A2XFY, O/G cable:-1R X 3C X 50 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,191.5 -3.50% 8,870 0.00 -8869.81
4.1.8 Incoming Cable : 1R X 3C X 95 sq. mm. A2XFY, O/G cable:-1R X 3C X 70 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,191.5 -3.50% 8,870 0.00 -8869.81
4.1.9 Incoming Cable : 1R X 3C X 120 sq. mm. A2XFY, O/G cable:-1R X 3C X 95 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,504.9 -3.50% 9,172 0.00 -9172.19
4.1.10 Incoming Cable : 1R X 3C X 150 sq. mm. A2XFY, O/G cable:-1R X 3C X 120 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,504.9 -3.50% 9,172 0.00 -9172.19
4.1.11 Incoming Cable : 1R X 3C X 185 sq. mm. A2XFY, O/G cable:-1R X 3C X 150 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,504.9 -3.50% 9,172 0.00 -9172.19
4.1.12 Incoming Cable : 1R X 3C X 240 sq. mm. A2XFY, O/G cable:-1R X 3C X 185 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 10,027.1 -3.50% 9,676 0.00 -9676.15
4.1.13 Incoming Cable : 1R X 3C X 6 sq. mm. 2XWY, O/G cable:-1R X 3C X 2.5 sq. mm. 2XWY, Exd, IIC, T3 1 0 -1 8,564.8 -3.50% 8,265 0.00 -8265.05
4.1.14 Incoming Cable : 1R X 3C X 10 sq. mm. 2XWY, O/G cable:-1R X 3C X 4 sq. mm. 2XWY, Exd, IIC, T3 1 0 -1 8,564.8 -3.50% 8,265 0.00 -8265.05
4.1.15 Incoming Cable : 1R X 3C X 16 sq. mm. A2XFY, O/G cable:-1R X 3C X 6 sq. mm. 2XWY, Exd, IIC, T3 1 0 -1 8,564.8 -3.50% 8,265 0.00 -8265.05
4.1.16 Incoming Cable : 1R X 3C X 25 sq. mm. A2XFY, O/G cable:-1R X 3C X 10 sq. mm. 2XWY, Exd, IIC, T3 1 0 -1 8,878.2 -3.50% 8,567 0.00 -8567.43
4.1.17 Incoming Cable : 1R X 3C X 35 sq. mm. A2XFY, O/G cable:-1R X 3C X 16 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 8,878.2 -3.50% 8,567 0.00 -8567.43
4.1.18 Incoming Cable : 1R X 3C X 50 sq. mm. A2XFY, O/G cable:-1R X 3C X 25 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 8,878.2 -3.50% 8,567 0.00 -8567.43
4.1.19 Incoming Cable : 1R X 3C X 70 sq. mm. A2XFY, O/G cable:-1R X 3C X 35 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,191.5 -3.50% 8,870 0.00 -8869.81
4.1.20 Incoming Cable : 1R X 3C X 95 sq. mm. A2XFY, O/G cable:-1R X 3C X 50 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,191.5 -3.50% 8,870 0.00 -8869.81
4.1.21 Incoming Cable : 1R X 3C X 120 sq. mm. A2XFY, O/G cable:-1R X 3C X 70 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,504.9 -3.50% 9,172 0.00 -9172.19
4.1.22 Incoming Cable : 1R X 3C X 150 sq. mm. A2XFY, O/G cable:-1R X 3C X 95 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,504.9 -3.50% 9,172 0.00 -9172.19
4.1.23 Incoming Cable : 1R X 3C X 185 sq. mm. A2XFY, O/G cable:-1R X 3C X 120 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,504.9 -3.50% 9,172 0.00 -9172.19
4.1.24 Incoming Cable : 1R X 3C X 240 sq. mm. A2XFY, O/G cable:-1R X 3C X 150 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 10,027.1 -3.50% 9,676 0.00 -9676.15
4.1.25 Incoming Cable : 1R X 3C X 25 sq. mm. A2XFY, O/G cable:-1R X 3C X 6 sq. mm. 2XWY, Exd, IIC, T3 1 0 -1 8,878.2 -3.50% 8,567 0.00 -8567.43
4.1.26 Incoming Cable : 1R X 3C X 35 sq. mm. A2XFY, O/G cable:-1R X 3C X 10 sq. mm. 2XWY, Exd, IIC, T3 1 0 -1 8,878.2 -3.50% 8,567 0.00 -8567.43
4.1.27 Incoming Cable : 1R X 3C X 50 sq. mm. A2XFY, O/G cable:-1R X 3C X 16 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 8,878.2 -3.50% 8,567 0.00 -8567.43
4.1.28 Incoming Cable : 1R X 3C X 70 sq. mm. A2XFY, O/G cable:-1R X 3C X 25 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,191.5 -3.50% 8,870 0.00 -8869.81
4.1.29 Incoming Cable : 1R X 3C X 95 sq. mm. A2XFY, O/G cable:-1R X 3C X 35 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,191.5 -3.50% 8,870 0.00 -8869.81
4.1.30 Incoming Cable : 1R X 3C X 120 sq. mm. A2XFY, O/G cable:-1R X 3C X 50 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,504.9 -3.50% 9,172 0.00 -9172.19
4.1.31 Incoming Cable : 1R X 3C X 150 sq. mm. A2XFY, O/G cable:-1R X 3C X 70 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,504.9 -3.50% 9,172 0.00 -9172.19
4.1.32 Incoming Cable : 1R X 3C X 185 sq. mm. A2XFY, O/G cable:-1R X 3C X 950 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 9,504.9 -3.50% 9,172 0.00 -9172.19
4.1.33 Incoming Cable : 1R X 3C X 240 sq. mm. A2XFY, O/G cable:-1R X 3C X 120 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 10,027.1 -3.50% 9,676 0.00 -9676.15
4.1.34 Incoming Cable : 2R X 3C X 240 sq. mm. A2XFY, O/G cable:-2R X 3C X 185 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 10,653.8 -3.50% 10,281 0.00 -10280.91
4.1.35 Incoming Cable : 2R X 3C X 240 sq. mm. A2XFY, O/G cable:-1R X 3C X 240 sq. mm. A2XFY, Exd, IIC, T3 1 0 -1 10,653.8 -3.50% 10,281 0.00 -10280.91
4.2 4 WAY JUNCTION BOX WITH TERMINAL BLOCK (WEATHER PROOF/INDUSTRIAL) :
4.2.1 Incoming Cable : 3C X 2.5 sq. mm., O/G Entries 3 Nos. suitable for : 3C x 2.5 sq. mm. cable. 1 1 0 1,932.3 -3.50% 1,865 1,865 0.00
4.3 4 WAY JUNCTION BOX WITH TERMINAL BLOCK, SUITABLE FOR GAS GROUP - IIC, TEMPERATURE CLASS - T3 (FLAMEPROOF):
4.3.1 Incoming Cable : 3C X 2.5 sq. mm., O/G Entries 3 Nos. suitable for : 3C x 2.5 sq. mm. cable. 1 1 0 5,483.6 -3.50% 5,292 5,292 0.00
4.4 4 WAY JUNCTION BOX WITH TERMINAL BLOCK, SUITABLE FOR GAS GROUP - IIB, TEMP. CLASS - T3 (FLAMEPROOF):
4.4.1 Incoming Cable : 3C X 2.5 sq. mm., O/G Entries 3 Nos. suitable for : 3C x 2.5 sq. mm. cable. 1 1 0 5,483.6 -3.50% 5,292 5,292 0.00
4.5 3 WAY JUNCTION BOX WITH TERMINAL BLOCK (WEATHER PROOF/INDUSTRIAL) :
4.5.1 Incoming Cable : 3C X 2.5 sq. mm., O/G Entries 3 Nos. suitable for : 3C x 2.5 sq. mm. cable. 1 1 0 1,850.0 -3.50% 1,785 1,785 0.00
4.6 3 WAY JUNCTION BOX WITH TERMINAL BLOCK, SUITABLE FOR GAS GROUP - IIC, TEMPERATURE CLASS - T3 (FLAMEPROOF):
4.6.1 Incoming Cable : 3C X 2.5 sq. mm., O/G Entries 3 Nos. suitable for : 3C x 2.5 sq. mm. cable. 1 1 0 4,775.0 -3.50% 4,608 4,608 0.00
4.7 3 WAY JUNCTION BOX WITH TERMINAL BLOCK, SUITABLE FOR GAS GROUP - IIB, TEMP. CLASS - T3 (FLAMEPROOF):
4.7.1 Incoming Cable : 3C X 2.5 sq. mm., O/G Entries 3 Nos. suitable for : 3C x 2.5 sq. mm. cable. 1 1 0 4,775.0 -3.50% 4,608 4,608 0.00
Addition or
Item No. Description Qty. Total revised QTY Rate (INR) Discount Final rate Total Revised Cost Total Cost of Excess Items
deletion
5 CANOPIES -
5.1 Supply, fabrication and/ or installation of GI / FRP canopies for outdoor electrical motors of following frame sizes to render them
weather proof including supply of necessary hardware for fixing and clamping with the motor foundation, including all labour and
materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.
Frame size upto 80. - 1 0 -1 5,849.1 -3.50% 5,644 0.00 -5644.42
Frame size more than 80 and upto 112. - 1 0 -1 8,564.8 -3.50% 8,265 0.00 -8265.05
Frame size more than 112 and upto 180. - 4 0 -4 10,653.8 -3.50% 10,281 0.00 -41123.65
Frame size more than 180 and upto 250. - 1 0 -1 13,421.7 -3.50% 12,952 0.00 -12951.93
Frame size more than 250 and upto 315. - 4 0 -4 21,307.6 -3.50% 20,562 0.00 -82247.30
5.2 Supply, fabrication and / or installation of GI / FRP canopies for outdoor electrical miscellaneous equipments such as
Local control station to render them weather proof including supply of necessary hardware for fixing and clamping with the equipment,
including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.
Push button stations. - 12 0 -12 5,744.7 -3.50% 5,544 0.00 -66523.55
7 CABLE TRAYS
7.1 Supply and installation of prefabricated hot dip galvanized Ladder type steel cable trays
Scope of work includes supply of the following sizes of GI cable trays of ladder type made out of hot rolled sheet steel of 2mm thick and
100 mm high collar/depth along with related accessories such as elbows, tees, crosses, couplers plates, cable tray materials, including
all other hardware and consumables required for installation as per approved drawings, specifications of this tender and directions
of Engineer-in-Charge. Scope also includes fabrication of cable tray supports (wherever necessary) and installation of trays on the
available tray supports / fabricated supports including welding and bolting of cable trays in existing/new supports inclusive of all labour.
Joints, bends and couplers quantity is to be ensured as per the actual site requirement. One tray is approx 2.5 mts lengths so for ex.100 mtrs
approx 40*2 (80) couple joints will be required. Similarly for bends separate coupler plates to be considered. Requirement of vertical
and horizontal bends will be as per approved drawing
7.1.1 750mm Wide Ladder Type Cable Tray 4500 5600 1100 1,295.2 -3.50% 1,250 6,999,084 1374820.14
7.1.2 750mm Wide Ladder Type 0.91 mm (20 gauge) Cable Tray Cover (Top and Bottom Cover) 4500 5600 1100 1,932.3 -3.50% 1,865 10,442,182 2051142.95
7.1.3 750mm Wide 900 1200 mm bending radius Horizontal bend including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.4 750mm Wide 900 900 mm bending radius Horizontal bend including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.5 750mm Wide 900 600 mm bending radius Horizontal bend including cover 5 5 0 4,642.8 -3.50% 4,480 22,401 0.00
7.1.6 750mm Wide 450 1200 mm bending radius Horizontal bend including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.7 750mm Wide Vertical inside 90 0 bend 1200 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.8 750mm Wide Vertical inside 90 0 bend 900 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.9 750mm Wide Vertical inside 45 0 bend 1200 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.10 750mm Wide Vertical outside 90 0 bend 1200 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.11 750mm Wide Vertical outside 90 0 bend 900 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.12 750mm Wide Vertical outside 45 0 bend 1200 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.13 Tee Junction for 750 mm wide 600 mm Radius 5 5 0 4,851.7 -3.50% 4,682 23,409 0.00
7.1.14 Tee Junction for 750 mm wide 1200 mm Radius 5 5 0 5,060.6 -3.50% 4,883 24,417 0.00
7.1.15 Unequal Tee Junction for 750 mm wide 600 x 600 mm Radius 5 5 0 4,851.7 -3.50% 4,682 23,409 0.00
7.1.16 Unequal Tee Junction for 750 mm wide 300 x 600 mm Radius 5 5 0 1,728.6 -3.50% 1,668 8,341 0.00
7.1.17 750 mm to 600 mm Reducer - Right Hand 5 5 0 3,713.2 -3.50% 3,583 17,916 0.00
7.1.18 750 mm to 600 mm Reducer cover - Right Hand 5 5 0 5,588.0 -3.50% 5,392 26,962 0.00
7.1.19 750 mm to 300 mm Reducer - Right Hand 5 5 0 3,713.2 -3.50% 3,583 17,916 0.00
7.1.20 750 mm to 300 mm Reducer cover - Right Hand 5 5 0 5,588.0 -3.50% 5,392 26,962 0.00
7.1.21 Cover for Tee Junction for 750 mm wide tray 5 5 0 5,986.0 -3.50% 5,776 28,882 0.00
7.1.22 450mm Wide Ladder Type Cable Tray 4400 1200 -3200 953.3 -3.50% 920 1,103,888 -2943702.58
7.1.23 450mm Wide Ladder Type 0.91 mm (20 gauge) Cable Tray Cover (Top and Bottom Cover) 4400 1200 -3200 1,422.2 -3.50% 1,372 1,646,930 -4391814.33
7.1.24 450mm Wide 900 1200 mm bending radius Horizontal bend including cover 5 5 0 3,955.3 -3.50% 3,817 19,084 0.00
Addition or
Item No. Description Qty. Total revised QTY Rate (INR) Discount Final rate Total Revised Cost Total Cost of Excess Items
deletion
7.1.25 450mm Wide 900 900 mm bending radius Horizontal bend including cover 5 5 0 3,955.3 -3.50% 3,817 19,084 0.00
7.1.26 450mm Wide 900 600 mm bending radius Horizontal bend including cover 5 5 0 3,417.2 -3.50% 3,298 16,488 0.00
7.1.27 450mm Wide 450 1200 mm bending radius Horizontal bend including cover 5 5 0 3,955.3 -3.50% 3,817 19,084 0.00
7.1.28 450mm Wide Vertical inside 90 0 bend 1200 mm bending Radius including cover 5 5 0 3,955.3 -3.50% 3,817 19,084 0.00
7.1.29 450mm Wide Vertical inside 90 0 bend 900 mm bending Radius including cover 5 5 0 3,955.3 -3.50% 3,817 19,084 0.00
7.1.30 450mm Wide Vertical inside 45 0 bend 1200 mm bending Radius including cover 5 5 0 3,955.3 -3.50% 3,817 19,084 0.00
7.1.31 450mm Wide Vertical outside 90 0 bend 1200 mm bending Radius including cover 5 5 0 3,955.3 -3.50% 3,817 19,084 0.00
7.1.32 450mm Wide Vertical outside 90 0 bend 900 mm bending Radius including cover 5 5 0 3,955.3 -3.50% 3,817 19,084 0.00
7.1.33 450mm Wide Vertical outside 45 0 bend 1200 mm bending Radius including cover 5 5 0 3,955.3 -3.50% 3,817 19,084 0.00
7.1.34 Tee Junction for 450 mm wide 600 mm Radius 5 5 0 3,570.9 -3.50% 3,446 17,230 0.00
7.1.35 Tee Junction for 450 mm wide 1200 mm Radius 5 5 0 3,724.7 -3.50% 3,594 17,972 0.00
7.1.36 Unequal Tee Junction for 450 mm wide 600 x 600 mm Radius 5 5 0 3,570.9 -3.50% 3,446 17,230 0.00
7.1.37 Unequal Tee Junction for 450 mm wide 300 x 600 mm Radius 5 5 0 1,272.3 -3.50% 1,228 6,139 0.00
7.1.38 450 mm to 300 mm Reducer - Right Hand 5 5 0 2,733.0 -3.50% 2,637 13,187 0.00
7.1.39 450 mm to 300 mm Reducer cover - Right Hand 5 5 0 4,112.9 -3.50% 3,969 19,845 0.00
7.1.40 Cover for Tee Junction for 450 mm wide tray 5 5 0 4,405.8 -3.50% 4,252 21,258 0.00
7.1.41 600mm Wide Ladder Type Cable Tray 250 0 -250 1,284.7 -3.50% 1,240 0.00 -309939.29
7.1.42 600mm Wide Ladder Type 0.91 mm (20 gauge) Cable Tray Cover (Top and Bottom Cover) 250 0 -250 1,942.8 -3.50% 1,875 0.00 -468688.68
0
7.1.43 600mm Wide 90 1200 mm bending radius Horizontal bend 5 0 -5 3,572.2 -3.50% 3,447 0.00 -17235.65
7.1.44 600mm Wide 900 900 mm bending radius Horizontal bend 5 0 -5 3,572.2 -3.50% 3,447 0.00 -17235.65
7.1.45 600mm Wide 900 600 mm bending radius Horizontal bend 5 0 -5 3,133.5 -3.50% 3,024 0.00 -15118.99
7.1.46 600mm Wide 600 Horizontal bend including cover 5 0 -5 5,021.0 -3.50% 4,845 0.00 -24226.33
7.1.47 600mm Wide 450 Horizontal bend including cover 5 0 -5 5,021.0 -3.50% 4,845 0.00 -24226.33
7.1.48 600mm Wide Vertical inside 90 0 bend 1200 mm bending Radius including cover 5 0 -5 5,358.2 -3.50% 5,171 0.00 -25853.47
7.1.49 600mm Wide Vertical inside 30 0 bend 300 mm bending Radius including cover 5 0 -5 4,345.1 -3.50% 4,193 0.00 -20965.00
7.1.50 600mm Wide Vertical outside 90 0 bend 1200 mm bending Radius including cover 5 0 -5 5,358.2 -3.50% 5,171 0.00 -25853.47
7.1.51 600mm Wide Vertical outside 90 0 bend 600 mm bending Radius including cover 5 0 -5 5,358.2 -3.50% 5,171 0.00 -25853.47
7.1.52 600mm Wide Vertical outside 45 0 bend 1200 mm bending Radius including cover 5 0 -5 5,358.2 -3.50% 5,171 0.00 -25853.47
7.1.53 600mm Wide Vertical outside 30 0 bend 300 mm bending Radius including cover 5 0 -5 4,345.1 -3.50% 4,193 0.00 -20965.00
7.1.54 Tee Junction for 600 mm wide 600 mm Radius including cover 5 0 -5 7,280.1 -3.50% 7,025 0.00 -35126.45
7.1.55 Unequal Tee Junction for 600 mm wide 300 x 300 mm Radius including cover 5 0 -5 6,669.1 -3.50% 6,436 0.00 -32178.25
7.1.56 Unequal Tee Junction for 600 mm wide 300 x 600 mm Radius including cover 5 0 -5 6,669.1 -3.50% 6,436 0.00 -32178.25
7.1.57 600 mm to 300 mm Reducer including cover - Right Hand 5 0 -5 5,013.6 -3.50% 4,838 0.00 -24190.38
7.1.58 Cover for Tee Junction for 600 mm wide tray 5 0 -5 4,800.0 -3.50% 4,632 0.00 -23160.00
7.1.59 600 mm to 300 mm Reducer cover 5 0 -5 4,698.0 -3.50% 4,534 0.00 -22667.85
7.1.60 300 Wide Ladder Type Cable Tray 4200 200 -4000 960.9 -3.50% 927 185,460 -3709192.16
7.1.61 300 Wide Ladder Type 0.91 mm (20 gauge) Cable Tray Cover (Top and Bottom Cover) 4200 200 -4000 960.9 -3.50% 927 185,460 -3709192.16
7.1.62 300mm Wide 90 0 300 mm bending radius Horizontal bend including cover 5 5 0 3,916.8 -3.50% 3,780 18,899 0.00
7.1.63 300mm Wide 30 0 300 mm bending radius Horizontal bend including cover 5 5 0 3,916.8 -3.50% 3,780 18,899 0.00
7.1.64 300mm Wide Vertical inside 90 0 bend 300 mm bending Radius including cover 5 5 0 3,916.8 -3.50% 3,780 18,899 0.00
7.1.65 300mm Wide Vertical inside 30 0 bend 300 mm bending Radius including cover 5 5 0 3,916.8 -3.50% 3,780 18,899 0.00
7.1.66 300mm Wide Vertical outside 90 0 bend 300 mm bending Radius including cover 5 5 0 3,916.8 -3.50% 3,780 18,899 0.00
7.1.67 300mm Wide Vertical outside 30 0 bend 300 mm bending Radius including cover 5 5 0 3,916.8 -3.50% 3,780 18,899 0.00
7.1.68 Tee Junction for 300 mm wide 300 mm Radius including cover 5 5 0 5,849.1 -3.50% 5,644 28,222 0.00
7.1.69 Unequal Tee Junction for 300 mm wide 150 x 300 mm Radius including cover 5 5 0 5,849.1 -3.50% 5,644 28,222 0.00
7.1.70 750mm Wide 300 1200 mm bending radius Horizontal bend including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.71 750mm Wide Vertical inside 30 0 bend 900 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.72 750mm Wide Vertical outside 30 0 bend 900 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.73 750mm Wide Vertical inside 30 0 bend 1200 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.74 750mm Wide Vertical outside 30 0 bend 1200 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.75 750mm Wide Vertical inside 45 0 bend 600 mm bending Radius including cover 5 5 0 4,642.8 -3.50% 4,480 22,401 0.00
7.1.76 750mm Wide Vertical outside 45 0 bend 600 mm bending Radius including cover 5 5 0 4,642.8 -3.50% 4,480 22,401 0.00
7.1.77 750mm Wide Vertical inside 45 0 bend 900 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.78 750mm Wide Vertical outside 45 0 bend 900 mm bending Radius including cover 5 5 0 5,373.9 -3.50% 5,186 25,929 0.00
7.1.79 Tee Junction for 750 mm wide 900 mm Radius 5 5 0 5,060.6 -3.50% 4,883 24,417 0.00
7.1.80 Equal Junction for 750 mm wide 900 mm Radius 5 5 0 5,060.6 -3.50% 4,883 24,417 0.00
7.1.81 Unequal Tee Junction for 750 mm wide 600 x 1200 mm Radius including cover 5 5 0 6,890.0 -3.50% 6,649 33,244 0.00
7.1.82 Unequal Tee Junction for 750 mm wide 300 x 900 mm Radius including cover 5 5 0 6,890.0 -3.50% 6,649 33,244 0.00
7.1.83 600mm Wide 900 300 mm bending radius Horizontal bend including cover 5 0 -5 4,345.1 -3.50% 4,193 0.00 -20965.00
7.1.84 600mm Wide Vertical inside 30 0 bend 1200 mm bending Radius including cover 5 0 -5 5,358.2 -3.50% 5,171 0.00 -25853.47
7.1.85 600mm Wide Vertical outside 30 0 bend 1200 mm bending Radius including cover 5 0 -5 5,358.2 -3.50% 5,171 0.00 -25853.47
7.1.86 600 mm to 450 mm Right Hand Reducer including cover 5 0 -5 4,698.0 -3.50% 4,534 0.00 -22667.85
7.1.87 300mm Wide 900 600 mm bending radius Horizontal bend including cover 5 0 -5 3,916.8 -3.50% 3,780 0.00 -18898.74
7.1.88 300mm Wide Vertical inside 90 0 bend 600 mm bending Radius including cover 5 0 -5 3,916.8 -3.50% 3,780 0.00 -18898.74
7.1.89 300mm Wide Vertical outside 90 0 bend 600 mm bending Radius including cover 5 0 -5 3,916.8 -3.50% 3,780 0.00 -18898.74
7.2 Supply and installation of prefabricated hot dip galvanized Perforated type cable trays
Scope of work includes supply of the following sizes of GI cable trays of perforated type made out of out of hot rolled sheet steel of
2mm thick and 50 mm high along with related accessories such as elbows, tees, crosses, couplers plates, cable tray materials, including
all other hardware and consumables required for installation as per approved drawings, specifications of this tender and directions
of Engineer-in-Charge. Scope also includes fabrication of cable tray supports (wherever necessary) and installation of trays on the
available tray supports / fabricated supports including welding and bolting of cable trays in existing/new supports inclusive of all labour.
Joints, bends and couplers quantity is to be ensured as per the actual site requirement. One tray is approx 2.5 mts lengths so for ex.100 mtrs
approx 40*2 (80) couple joints will be required. Similarly for bends separate coupler plates to be considered. Requirement of vertical
and horizontal bends will be as per approved drawing
7.2.1 150mm Wide perforated Cable Tray 1000 1000 0 637.1 -3.50% 615 614,839 0.00
7.2.2 150mm Wide perforated Tray Cover (Top Cover) 1000 1000 0 637.1 -3.50% 615 614,839 0.00
Addition or
Item No. Description Qty. Total revised QTY Rate (INR) Discount Final rate Total Revised Cost Total Cost of Excess Items
deletion
7.2.3 150mm Wide 900 Horizontal bend 300 mm radius with cover 10 10 0 2,543.3 -3.50% 2,454 24,543 0.00
7.2.4 150mm Wide Vertical 90 0 inside bend 300 mm radius with cover 10 10 0 2,543.3 -3.50% 2,454 24,543 0.00
7.2.5 150mm Wide Vertical 90 0 outside bend 300 mm radius with cover 10 10 0 2,543.3 -3.50% 2,454 24,543 0.00
Tee Junction for 150 mm wide tray with cover.
7.2.6 10 10 0 3,859.4 -3.50% 3,724 37,243 0.00
8 LAYING OF CABLES -
8.1 Laying of cables (using cable pulling by motorized winch with torque limits) of different voltage grade (415V/6600V/33000V) and types of the
following overall diameters in ready trays/trenches/ supported on structure/pull through pipes including supply and fixing of stainless
steel/aluminium/lead strip number tags, supply and fixing of GI saddles and saddle bars etc., including transportation from store/yard to
site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender
and directions of Engineer-in-Charge -
Cables with OD upto 20 mm. - 7800 7800 0 27.7 -3.50% 27 208,188 0.00
Cables with OD above 20 mm but upto 30 mm. - 4800 4800 0 44.7 -3.50% 43 206,956 0.00
Cables with OD above 30 mm but upto 40 mm. - 100 100 0 67.0 -3.50% 65 6,467 0.00
Cables with OD above 40 mm but upto 50 mm. - 600 600 0 78.7 -3.50% 76 45,580 0.00
Cables with OD above 50 mm but upto 60 mm. - 2400 2400 0 95.7 -3.50% 92 221,738 0.00
Cables with OD above 60 mm but upto 80 mm. - 21200 21200 0 108.5 -3.50% 105 2,219,848 0.00
8.2 Laying of signal cables
Laying of cables (using cable pulling by motorized winch with torque limits) in ready trays/trenches/ supported on structure/pull
through pipes including supply and fixing of stainless steel/aluminium/lead strip number tags, supply and fixing of GI saddles and saddle
bars etc., including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as
per approved drawings, specifications of this tender and directions of Engineer-in-Charge -
All sizes from 1P to 4P and upto 2.5 sq. mm - 100 100 0 21.3 -3.50% 21 2,053 0.00
All sizes from 5P to 10P and upto 2.5 sq. mm - 100 100 0 39.4 -3.50% 38 3,798 0.00
All sizes from 11P to 50 P and upto 2.5 sq. mm - 100 100 0 98.9 -3.50% 95 9,547 0.00
All sizes from 50 P to 100 P and upto 2.5 sq. mm - 100 100 0 150.0 -3.50% 145 14,471 0.00
All sizes from 1T to 8T and upto 2.5 sq. mm - 2000 2000 0 39.4 -3.50% 38 75,966 0.00
8.3 RS 485 cables
The scope of work includes supply, laying and termination of RS 485 cables.
The scope of work includes laying in pre excavated cable trench /existing concrete trenches,/cable trays, supported on structure/pull
through pipes, dewatering if required, including supply and fixing of Aluminium strip number tags, supply and fixing of GI saddles and
saddle bars,etc. including transportation from IOCL's Haldia refinery stores to site. Unpacking including disposal of packing materials
(wooden, thermocol, plastic etc.) inside refinery premises, with all labour and material as per specification of this tender of and
directions of Engineer-in-Charge.
24 AWG stranded annealed tinned copper conductor, 2 twisted pairs (10 Twists/ mtr.), overall foil and tinned copper braid shielded 300 300 0 37.3 -3.50% 36 10,804 0.00
with 24 AWG strand tinned copper drain wire, XLPE insulated, GI steel wire armoured, FRLS PVC ST2 inner and outer sheath cable.
8.4 FIBRE OPTIC CABLE
The scope of work includes supply including required interface unit at both ends, horizontal and vertical laying and termination of
Fibre optic cables The scope of work includes laying in pre excavated cable trench /existing concrete trenches,/cable trays, supported
on structure/pull through pipes, dewatering if required, including supply and fixing of Aluminium strip number tags, supply and fixing of
GI saddles and saddle bars,etc. including transportation from IOCL's Haldia refinery stores to site. Unpacking including disposal of
packing materials (wooden, thermocol, plastic etc.) inside refinery premises, with all labour and material as per specification of this
tender of and directions of Engineer-in-Charge.
Single mode SM 9/125 μm glass fibre core suitable for 1300nm wavelength 200 0 -200 134.0 -3.50% 129 0.00 -25862.00
Multimode MM 62.5/125 μm glass fibre core suitable for 1300nm wavelength 200 200 0 193.2 -3.50% 186 37,294 0.00
Existing cable rerouting to be done by the executing agency and any damage during cable pulling to be rectified by the executing agency without any price and schedule
8.5 1 1 0 - -3.50% - 0.00 0.00
implication to Owner/PMC.
9 END TERMINATIONS -
9.1 Supply and termination of (indoor/outdoor type) heat shrinkable Raychem make Unearthed grade 6.6kV H.V. termination kits
excluding cable glands and lugs, as per approved drawings and as per specifications of this tender and directions of Engineer- in-Charge.
Termination of Unearthed grade HV cables includes connection of leads, fixing of cable glands, supply and fixing of PVC shrouds for
outdoor terminations, cutting and stripping of cable insulation, crimping the lug onto the conductor, restoration of the insulation,
clamping of cable cores and earthing of armour, including all labour and materials, as per approved drawings, specifications of this
tender and directions of Engineer-in-Charge. (Excluding supply of cable glands). -
9.1.1 3 Core cables (Indoor) 6.6 kV , 240 sqmm 2 2 0 8,355.9 -3.50% 8,063 16,127 0.00
9.1.2 3 Core cables (Outdoor) 6.6 kV , 240 sqmm 2 2 0 8,355.9 -3.50% 8,063 16,127 0.00
9.1.3 1 Core cables (Indoor) 33 kV , 400 sqmm 12 12 0 37,000.0 -3.50% 35,705 428,460 0.00
9.2 Termination of 1.1 kV grade power cables and connection of leads including fixing of cable leads excluding the supply of
cable glands and lugs but including fixing of cable glands, cutting and stripping of cable insulation, crimping the lug on to the conductor,
clamping of the cable-cores, marking with wire number, ferrules etc., including all labour and materials, as per approved drawings,
specifications of this tender and directions of Engineer-in-Charge. -
9.2.1 Cables with OD upto 20 mm. - 87 87 0 404.2 -3.50% 390 33,938 0.00
9.2.2 Cables with OD above 20 mm but upto 30 mm. - 10 10 0 473.4 -3.50% 457 4,568 0.00
9.2.3 Cables with OD above 30 mm but upto 40 mm. - 2 2 0 638.3 -3.50% 616 1,232 0.00
9.2.4 Cables with OD above 40 mm but upto 50 mm. - 2 2 0 1,031.9 -3.50% 996 1,992 0.00
Addition or
Item No. Description Qty. Total revised QTY Rate (INR) Discount Final rate Total Revised Cost Total Cost of Excess Items
deletion
9.2.5 Cables with OD above 50 mm but upto 60 mm. - 8 8 0 1,196.8 -3.50% 1,155 9,239 0.00
Scope includes connection of leads excluding the supply of cable glands and lugs but including fixing of cable glands, cutting, stripping of
cable insulation, crimping the lug on to the conductor, clamping of the cable- cores, marking with wire number, ferrules etc., including
all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. -
9.3.1 All sizes from 2 to 7 cores and upto 2.5 sq. mm. - 20 20 0 196.8 -3.50% 190 3,798 0.00
9.3.2 All sizes from 12 to 19 cores and upto 2.5 sq. mm. - 1 1 0 363.8 -3.50% 351 351 0.00
9.3.3 All sizes from 1P to 4P and upto 2.5 sq. mm - 1 1 0 197.9 -3.50% 191 191 0.00
9.3.4 All sizes from 5P to 10P and upto 2.5 sq. mm - 1 1 0 436.2 -3.50% 421 421 0.00
9.3.5 All sizes from 11P to 50 P and upto 2.5 sq. mm - 1 1 0 542.5 -3.50% 524 524 0.00
9.3.6 All sizes from 51 P to 100 P and upto 2.5 sq. mm - 1 1 0 851.0 -3.50% 821 821 0.00
9.3.7 All sizes from 1T to 8T and upto 2.5 sq. mm - 4 4 0 202.1 -3.50% 195 780 0.00
10.1.6 Cables with OD above 60 mm but upto 80 mm. - 2 0 -2 35,963.9 -3.50% 34,705 0.00 -69410.28
10.2 Supply and Making of heat shrinkable type straight through joints for unearthed grade 415 volt grade cables including cutting,
stripping of cable insulation complete with supply of compression / crimping type ferrules, plastic mould and epoxy resin compound etc.,
including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.
10.2.1 Cables with OD upto 20 mm. - 2 2 0 3,431.1 -3.50% 3,311 6,622 0.00
10.2.2 Cables with OD above 20 mm but upto 30 mm. - 2 2 0 4,507.0 -3.50% 4,349 8,698 0.00
10.2.3 Cables with OD above 30 mm but upto 40 mm. - 2 2 0 4,470.4 -3.50% 4,314 8,628 0.00
10.2.4 Cables with OD above 40 mm but upto 50 mm. - 2 2 0 4,470.4 -3.50% 4,314 8,628 0.00
10.2.5 Cables with OD above 50 mm but upto 60 mm. - 2 2 0 4,470.4 -3.50% 4,314 8,628 0.00
10.2.6 Cables with OD above 60 mm but upto 80 mm. - 2 2 0 4,470.4 -3.50% 4,314 8,628 0.00
10.3 Supply and Making of heat shrinkable type straight through joints for unearthed grade 33000 volt grade cables including cutting,
stripping of cable insulation complete with supply of compression / crimping type ferrules, plastic mould and epoxy resin compound etc.,
including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.
10.3.1 Cables with OD above 60 mm but upto 80 mm. - 42 18 -24 26,700.0 -3.50% 25,766 463,779 -618372.00
11 CABLE GLANDS -
11.1 Supply of nickel-plated, flame proof IIC double compression type brass cable glands, suitable for out door terminations of XLPE
armoured PVC sheathed FRLS cables of following overall diameter (excluding termination and connection of cables), including all labour
and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.
11.1.1 Cables with OD upto 20 mm. 103 103 0 450.8 -3.50% 435 44,803 0.00
11.1.2 Cables with OD above 20 mm but upto 30 mm. 7 7 0 663.2 -3.50% 640 4,480 0.00
11.1.3 Cables with OD above 30 mm but upto 40 mm. 1 1 0 1,300.4 -3.50% 1,255 1,255 0.00
11.1.4 Cables with OD above 40 mm but upto 50 mm. 1 1 0 2,258.9 -3.50% 2,180 2,180 0.00
11.1.5 Cables with OD above 50 mm but upto 60 mm. 4 4 0 2,746.0 -3.50% 2,650 10,599 0.00
11.1.6 Cables with OD above 60 mm but upto 80 mm. 2 2 0 3,834.0 -3.50% 3,700 7,400 0.00
11.2 Supply of nickel plated brass double compression cable glands suitable for indoor installations of XLPE armoured PVC sheathed FRLS
cable for following overall diameter (excluding termination and connections of cables), including drilling of suitable holes in equipments
for fixing purposes etc., including all labour and materials, as per approved drawings, specifications of this tender and directions of
Engineer-in-Charge. -
11.2.1 Cables with OD upto 20 mm. 14 14 0 336.8 -3.50% 325 4,550 0.00
11.2.2 Cables with OD above 20 mm but upto 30 mm. 7 7 0 601.0 -3.50% 580 4,060 0.00
11.2.3 Cables with OD above 30 mm but upto 40 mm. 1 1 0 1,367.8 -3.50% 1,320 1,320 0.00
11.2.4 Cables with OD above 40 mm but upto 50 mm. 1 1 0 1,657.9 -3.50% 1,600 1,600 0.00
11.2.5 Cables with OD above 50 mm but upto 60 mm. 4 4 0 2,290.0 -3.50% 2,210 8,840 0.00
11.2.6 Cables with OD above 60 mm but upto 80 mm. 2 2 0 3,502.4 -3.50% 3,380 6,760 0.00
12 CABLE LUGS -
Supply of crimping type bi-metallic lugs with circular/sector shaped barrel for following conductor sizes, as per approved drawings,
specifications of this tender and directions of Engineer-in-Charge. -
12.1 All sizes upto 10 sq. mm. - 350 350 0 18.7 -3.50% 18 6,300 0.00
12.2 All sizes from 16 to 35 sq. mm - 24 24 0 35.2 -3.50% 34 816 0.00
12.3 All sizes from 50 to 185 sq. mm - 30 30 0 207.2 -3.50% 200 6,000 0.00
12.4 All sizes from 240 to 400 sq. mm - 36 36 0 352.3 -3.50% 340 12,239 0.00
13 Fire proofing of cables including supply of fire proofing paint, applying fire proofing paint to the cable at both the ends of termination 30 30 0 1,500.0 -3.50% 1,448 43,425 0.00
upto 3 mtr length to withstand fire for minimum 30min., including all labour and materials, as per IEC-60331, specifications of this
tender and directions of Engineer-in- Charge. (Actual area of surface painted shall be measured). -
Addition or
Item No. Description Qty. Total revised QTY Rate (INR) Discount Final rate Total Revised Cost Total Cost of Excess Items
deletion
14 ADAPTORS/REDUCERS/NIPPLES ETC. -
14.1 Supply and fixing nickel-plated brass adaptors/ reducers for cable glands of following sizes including all labour and materials complete as
per approved drawings, specifications of this tender and directions of Engineer-in-Charge. Adaptors shall have male part threaded as
per Eqpt. threads and the other end to receive glands having E.T. thread. -
14.1.1 Eqpt. Thread 3/4" PF (J.I.S.)-E.T. Thread 3/4"ET 2 0 -2 1,284.7 -3.50% 1,240 0.00 -2479.51
14.1.2 Eqpt. Thread 1" PF (J.I.S.) - E.T. Thread 3/4"ET 2 0 -2 1,284.7 -3.50% 1,240 0.00 -2479.51
14.1.3 Eqpt. Thread 1" PF (J.I.S.) -E.T. Thread 1"ET 2 0 -2 1,410.1 -3.50% 1,361 0.00 -2721.42
14.1.4 Eqpt. Thread 1-1/2" PF (J.I.S.)- E.T. Thread 1-1/4"ET 2 0 -2 1,566.7 -3.50% 1,512 0.00 -3023.80
14.1.5 Eqpt. Thread 1-1/2" PF (J.I.S.)- E.T. Thread 1-1/2"ET 2 0 -2 1,775.6 -3.50% 1,713 0.00 -3426.97
14.1.6 Eqpt. Thread 2" PF (J.I.S.) -E.T. Thread 1-1/2 "ET 2 0 -2 1,775.6 -3.50% 1,713 0.00 -3426.97
14.2 Supply and fixing FLP(IIA/IIB), weatherproof, nickel-plated brass adaptors/reducers for cable glands of following sizes including all labour
and materials complete as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. Adaptors shall
have male part threaded as per Eqpt. threads and the other end to receive glands having E.T. thread. -
14.2.1 Eqpt. Thread 3/4" PF (J.I.S.)-E.T. Thread 3/4"ET - 2 0 -2 1,284.7 -3.50% 1,240 0.00 -2479.51
14.2.2 Eqpt. Thread 1" PF (J.I.S.) -E.T. Thread 3/4"ET - 2 0 -2 1,284.7 -3.50% 1,240 0.00 -2479.51
14.2.3 Eqpt. Thread 1" PF (J.I.S.) -E.T. Thread 1"ET 2 0 -2 1,389.2 -3.50% 1,341 0.00 -2681.10
14.2.4 Eqpt. Thread 1-1/2" PF (J.I.S.)- E.T. Thread 1-1/4"ET - 2 0 -2 1,566.7 -3.50% 1,512 0.00 -3023.80
14.2.5 Eqpt. Thread 1-1/2" PF (J.I.S.)- E.T. Thread 1-1/2"ET - 2 0 -2 1,827.9 -3.50% 1,764 0.00 -3527.76
14.2.6 Eqpt. Thread 2" PF (J.I.S.) -E.T. Thread 1-1/2"ET - 2 0 -2 1,827.9 -3.50% 1,764 0.00 -3527.76
14.3 Supply and fixing FLP(IIC), weatherproof, nickel-plated brass adaptors/reducers for cable glands of following sizes including all labour
and materials complete as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. Adaptors shall
have male part threaded as per Eqpt. threads and the other end to receive glands having E.T. thread. -
14.3.1 Eqpt. Thread 3/4" PF (J.I.S.)-E.T. Thread 3/4"ET 2 0 -2 1,284.7 -3.50% 1,240 0.00 -2479.51
14.3.2 Eqpt. Thread 1" PF (J.I.S.) -E.T. Thread 3/4"ET - 2 0 -2 1,284.7 -3.50% 1,240 0.00 -2479.51
14.3.3 Eqpt. Thread 1" PF (J.I.S.) -E.T. Thread 1"ET - 2 0 -2 1,389.2 -3.50% 1,341 0.00 -2681.10
14.3.4 Eqpt. Thread 1-1/2" PF (J.I.S.)- E.T. Thread 1-1/4"ET - 2 0 -2 1,566.7 -3.50% 1,512 0.00 -3023.80
14.3.5 Eqpt. Thread 1-1/2" PF (J.I.S.)- E.T. Thread 1-1/2"ET - 2 0 -2 1,827.9 -3.50% 1,764 0.00 -3527.76
14.3.6 Eqpt. Thread 2" PF (J.I.S.) -E.T. Thread 1-1/2"ET - 2 0 -2 1,827.9 -3.50% 1,764 0.00 -3527.76
14.4 Supply and installation of FLP(IIC) GI reducers/ enlargers of following sizes for cable glands of following sizes including all labour and
materials complete as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. Adaptors shall have
male part threaded as per Eqpt. threads and the other end to receive glands having E.T. thread. -
14.4.1 Eqpt. Thread PG 13.5(DIN) - E.T. Thread 3/4" ET - 2 0 -2 1,284.7 -3.50% 1,240 0.00 -2479.51
14.4.2 Eqpt. Thread PG 16 (DIN) -E.T. Thread 3/4" ET - 2 0 -2 1,284.7 -3.50% 1,240 0.00 -2479.51
14.4.3 Eqpt. Thread PG 21 (DIN) -E.T. Thread 1"ET - 2 0 -2 1,389.2 -3.50% 1,341 0.00 -2681.10
14.4.4 Eqpt. Thread PG 29 (DIN) -E.T. Thread 1-1/2" ET - 2 0 -2 1,827.9 -3.50% 1,764 0.00 -3527.76
14.4.5 Eqpt. Thread 1" ET (IS) -E.T. Thread 3/4" ET - 2 0 -2 1,284.7 -3.50% 1,240 0.00 -2479.51
14.4.6 Eqpt. Thread 1-1/2" ET (IS) -E.T. Thread 1" ET - 2 0 -2 1,389.2 -3.50% 1,341 0.00 -2681.10
14.4.7 Eqpt. Thread 1-1/2" ET (IS) -E.T. Thread 1-1/2" ET - 2 0 -2 1,827.9 -3.50% 1,764 0.00 -3527.76
14.4.8 Eqpt. Thread 2" ET (IS) -E.T. Thread 1-1/2" ET - 2 0 -2 1,827.9 -3.50% 1,764 0.00 -3527.76
15 LIGHTING SYSTEM
15.1 Supply, Installation, connection, testing and commissioning of following types of Industrial/ commercial lighting fixtures,
accessories, driver, cable gland and all necessary mounting brackets / looping boxes / pipes as applicable, Minor Civil Works & other
consumable like anchor fasteners/studs, nuts and bolts etc. required for the complete installation generally as per Miscellaneous Lighting
Detail drawing including supply of all items indicated in the Miscellaneous Lighting Detail drawings,
including cable termination and connection, fixing of cable glands, lugs, including supply of necessary hardware's,
including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per
approved drawings, specifications of this tender and directions of Engineer-in-Charge. -
15.1.1 Fitting type-F23: LED FLOODLIGHT TYPE FLAMEPROOF LUMINAIRE WITH INTEGRAL TYPE DRIVER,WITH NOMINAL VOLTAGE OF 240V 2 2 0 11,996.0 -3.50% 11,576 23,152 0.00
AC, 50Hz, SUITABLE FOR CEILING/SURFACE/WALL/BRACKET MOUNTING, ZONE-1 AREA, GAS GROUP - IIC & TEMPERATURE CLASS T3,
INGRESS PROTECTION OF IP65, MINIMUM LUMEN OUTPUT OF 7500. LUMINAIRE SHALL HAVE A COLOR TEMPERATURE OF 5700K.
15.1.2 Fitting type - W41: LED WELLGLASS TYPE FLAMEPROOF LUMINAIRE WITH INTEGRAL TYPE DRIVER, WITH NOMINAL 25 25 0 7,479.0 -3.50% 7,217 180,430 0.00
VOLTAGE OF 240V AC, 50Hz, SUITABLE FOR CEILING/BRACKET/SUSPENSION MOUNTING, ZONE-1 AREA, GAS GROUP - IIB AND
TEMPERATURE CLASS T3, INGRESS PROTECTION OF IP65, MINIMUM LUMEN OUTPUT OF 3000. LUMINAIRE SHALL HAVE A COLOR
TEMPERATURE OF 5700K.
15.1.3 Fitting type - W42: LED WELLGLASS TYPE FLAMEPROOF LUMINAIRE WITH INTEGRAL TYPE DRIVER, WITH NOMINAL 2 2 0 7,479.0 -3.50% 7,217 14,434 0.00
VOLTAGE OF 110V DC, SUITABLE FOR CEILING/BRACKET/SUSPENSION MOUNTING, ZONE-1 AREA, GAS GROUP - IIB AND
TEMPERATURE CLASS T3, INGRESS PROTECTION OF IP65, MINIMUM LUMEN OUTPUT OF 3000. LUMINAIRE SHALL HAVE A COLOR
TEMPERATURE OF 5700K.
15.1.4 Fitting type - W43: LED WELLGLASS TYPE FLAMEPROOF LUMINAIRE WITH INTEGRAL TYPE DRIVER, WITH NOMINAL 2 2 0 7,479.0 -3.50% 7,217 14,434 0.00
VOLTAGE OF 220V DC, SUITABLE FOR CEILING/BRACKET/SUSPENSION MOUNTING, ZONE-1 AREA, GAS GROUP - IIB AND
TEMPERATURE CLASS T3, INGRESS PROTECTION OF IP65, MINIMUM LUMEN OUTPUT OF 3000. LUMINAIRE SHALL HAVE A COLOR
TEMPERATURE OF 5700K.
15.1.5 Fitting type - W44: LED WELLGLASS TYPE FLAMEPROOF LUMINAIRE WITH INTEGRAL TYPE DRIVER, WITH NOMINAL 25 25 0 7,479.0 -3.50% 7,217 180,430 0.00
VOLTAGE OF 240V AC, 50Hz, SUITABLE FOR CEILING/BRACKET/SUSPENSION MOUNTING, ZONE-1 AREA, GAS GROUP - IIC AND
TEMPERATURE CLASS T3, INGRESS PROTECTION OF IP65, MINIMUM LUMEN OUTPUT OF 3000. LUMINAIRE SHALL HAVE A COLOR
TEMPERATURE OF 5700K.
15.1.6 Fitting type - W45: LED WELLGLASS TYPE FLAMEPROOF LUMINAIRE WITH INTEGRAL TYPE DRIVER, WITH NOMINAL 2 2 0 7,479.0 -3.50% 7,217 14,434 0.00
VOLTAGE OF 110V DC, SUITABLE FOR CEILING/BRACKET/SUSPENSION MOUNTING, ZONE-1 AREA, GAS GROUP - IIB AND
TEMPERATURE CLASS T3, INGRESS PROTECTION OF IP65, MINIMUM LUMEN OUTPUT OF 3000. LUMINAIRE SHALL HAVE A COLOR
TEMPERATURE OF 5700K.
15.1.7 Fitting type - W46: LED WELLGLASS TYPE FLAMEPROOF LUMINAIRE WITH INTEGRAL TYPE DRIVER, WITH NOMINAL 2 2 0 7,479.0 -3.50% 7,217 14,434 0.00
VOLTAGE OF 220V DC, SUITABLE FOR CEILING/BRACKET/SUSPENSION MOUNTING, ZONE-1 AREA, GAS GROUP - IIB AND
TEMPERATURE CLASS T3, INGRESS PROTECTION OF IP65, MINIMUM LUMEN OUTPUT OF 3000. LUMINAIRE SHALL HAVE A COLOR
TEMPERATURE OF 5700K.
16 Lighting Poles
The scope of work includes supply, installation, field testing & commissioning of lighting poles of the following types including supply of
all necessary hardware and consumables like anchor fasteners/studs, nuts and bolts etc. , including the foundation and any other minor
civil works required for the complete installation as per specifications of this tender and directions of Engineer-in-Charge.
Addition or
Item No. Description Qty. Total revised QTY Rate (INR) Discount Final rate Total Revised Cost Total Cost of Excess Items
deletion
16.1 Pedestal/Platform/Wall/Column mounted lighting poles, G.I, complete with all hardware's, wires etc. with height of 2 Mts above ground as per lighting layouts. 1 1 0 6,998.2 -3.50% 6,753 6,753 0.00
16.1.1 Pedestal/Platform/Wall/Column mounted lighting poles, G.I, complete with all hardware's, wires etc. with height of 2.5 Mts above ground as per lighting layouts. 25 25 0 8,000.8 -3.50% 7,721 193,019 0.00
Pedestal/Platform/Wall/Column mounted lighting poles, G.I, complete with all hardware's, wires etc. with height of 3 Mts above ground as per lighting layouts &
16.1.2 1 1 0 8,925.7 -3.50% 8,613 8,613 0.00
installation details.
Pedestal/Platform/Wall/Column mounted lighting poles, G.I, complete with all hardware's, wires etc. with height of 3.5 Mts above ground as per lighting layouts &
16.1.3 1 1 0 9,790.6 -3.50% 9,448 9,448 0.00
installation details.
Pedestal/Platform/Wall/Column mounted lighting poles, G.I, complete with all hardware's, wires etc. with height of 4 Mts above ground as per lighting layouts &
16.1.4 1 1 0 10,607.3 -3.50% 10,236 10,236 0.00
installation details.
17.1 The scope of work includes Installation of following type of Flameproof local control stations (LCS), Zone-2,Ex"d", IIC,T3 along with FRP rain/weather
protection canopy as per specification of this tender and directions of Engineer-in- Charge.
17.1.1 Type-1F - Flame proof Ex (d) type with Start, Stop Push Button & L/R selector switch as applicable 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.1.2 Type-2F - Flame proof Ex (d) outdoor type with Start & Stop Push Buttons + Ammeter 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.1.3 Type-3F - Flame proof Ex (d) type with L/R & Emergency stop button (for more than 1000kW ) 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.1.4 Type-4F - Flame proof Ex (d) type with speed increase & decrease P.B, L/R selector switch, ammeter, Start P.B., Stop P.B. & RPM meter 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.1.5 Type-5F - Flame proof Ex (d) type with Start, Stop Push Button, L/R selector switch & ammeter switch as applicable 6 6 0 2,765.9 -3.50% 2,669 16,014 0.00
17.1.6 Type-6F - Flame proof Ex (d) type with Stop Push Button, L/R selector switch, forward/reverse push buttons & ammeter switch as applicable 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.1.7 Type-7F - Flame proof Ex (d) type with T-N-C selector switch, L/R selector switch & ammeter switch as applicable 2 2 0 2,765.9 -3.50% 2,669 5,338 0.00
17.2 The scope of work includes Installation of following type of Flameproof local control stations (LCS), Zone-2,Ex"d", IIB,T3 along with FRP rain/weather
protection canopy as per specification of this tender and directions of Engineer-in- Charge.
17.2.1 Type-1F - Flame proof Ex (d) type with Start, Stop Push Button & L/R selector switch as applicable 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.2.2 Type-2F - Flame proof Ex (d) outdoor type with Start & Stop Push Buttons + Ammeter 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.2.3 Type-3F - Flame proof Ex (d) type with L/R & Emergency stop button (for more than 1000kW ) 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.2.4 Type-4F - Flame proof Ex (d) type with speed increase & decrease P.B, L/R selector switch, ammeter, Start P.B., Stop P.B. & RPM meter 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.2.5 Type-5F - Flame proof Ex (d) type with Start, Stop Push Button, L/R selector switch & ammeter switch as applicable 6 6 0 2,765.9 -3.50% 2,669 16,014 0.00
17.2.6 Type-6F - Flame proof Ex (d) type with Stop Push Button, L/R selector switch, forward/reverse push buttons & ammeter switch as applicable 1 1 0 2,765.9 -3.50% 2,669 2,669 0.00
17.2.7 Type-7F - Flame proof Ex (d) type with T-N-C selector switch, L/R selector switch & ammeter switch as applicable 2 2 0 2,765.9 -3.50% 2,669 5,338 0.00
19 Supply of Fireproof sealing compound rated for 4 hrs. fire rating, heating and pouring of compound in the cable stuffing box of 5 5 0 1,100.0 -3.50% 1,062 5,308 0.00
flameproof motors, providing effective cable sealing for floor and wall cutouts , including all labour and materials, as per specifications
of this tender and as per directions of Engineer-in-Charge (Measurement of weight shall be made for sealing compound supplied).
20 The scope of work includes providing cable crossing under road using HDPE pipes of including all required civil work like breaking of road,
restoration of road to normal condition etc., as per specification of this tender and directions of Engineer-in-Charge:
20.1 150mm dia HDPE pipe 20 20 0 4,554.0 -3.50% 4,395 87,892 0.00
20.2 250mm dia HDPE pipe 15 15 0 12,116.1 -3.50% 11,692 175,380 0.00
20.3 40mm dia HDPE pipe Black color 6400 0 -6400 412.1 -3.50% 398 0.00 -2545125.56
20.4 40mm dia HDPE pipe Blue color 6400 0 -6400 412.1 -3.50% 398 0.00 -2545125.56
21 The scope of work includes supply and installation of cable markers for underground cable runs with 14 SWG enameled steel plate with white 30 30 0 856.5 -3.50% 827 24,795 0.00
lettering on jade green background inclusive of providing and fixing supports, including all labour and materials, as per approved drawings,
specifications of this tender and directions of Engineer-in-Charge.
22 Supply and installation of earth pit markers for directly buried GI pipe electrodes as per specification of this tender and drawing 40 40 0 10,236.0 -3.50% 9,878 395,110 0.00
with 14 SWG enameled steel plate engraved with white letters BURIED, EARTH ELECTRODE on JADE green background complete with support
and foundation, including all labour and materials, as per approved drawings, specifications of this tender and direction of Engineer-in-Charge. -
24 STRUCTURAL STEEL -
Supply, fabrication and installation of MS base frames, supports for switchgear, and brackets for miscellaneous electrical equipments, 5 5 0 151,511.2 -3.50% 146,208 731,042 0.00
cable and cable tray supports out of rolled MS sections, pipes, plates, push button station supports/ SVL/Cable link box/ EHT panel/ Sockets etc.
including shot blasting, welding, bolting, riveting, supply of necessary anchor bolts and grouting etc., supply of paint and applying of anti-rust
primer coat and finished coats of approved synthetic enamel paint as per painting specification attached with the tender document suitable for
highly corrosive environment, including breaking walls, floors etc. for structures as required including supply of all GI / stainless steel hardware
materials, all labour and materials complete as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.
(Any item weighing upto 1 kg. or less shall neither be measured nor paid).
25 G.I. PIPES -
The scope of work includes supply, laying of following sizes of G.I. Pipes (medium) in required length fixed on steel, concrete of similar
structure, laid in trenches, ready to be buried in concrete including cutting, threading, bending and similar works, supply of coupling,
clamps, small iron structures, spacers and installation of seats, plugs, bushings, sealing of pipe ends & joints with bushes and bitumen
based fillings and such other miscellaneous works so as to make piping water tight civil work for the demolition of specified area in
existing cable trench for laying the GI pipe and restoration of the same etc., small civil works, including all labour and materials, as per
specification of this tender and directions of Engineer-in-Charge.
25.1 50 mm NB. (Class B) 50 0 -50 564.0 -3.50% 544 0.00 -27214.18
25.2 100 mm NB. (Class B) 50 0 -50 1,410.1 -3.50% 1,361 0.00 -68035.45
25.3 150 mm NB. (Class B) 50 0 -50 2,141.2 -3.50% 2,066 0.00 -103313.10
25.4 50 mm NB. Elbow (Class B) 50 0 -50 710.3 -3.50% 685 0.00 -34269.71
25.5 100 mm NB. Elbow (Class B) 10 0 -10 3,081.2 -3.50% 2,973 0.00 -29734.01
25.6 150 mm NB. Elbow (Class B) 10 0 -10 3,929.9 -3.50% 3,792 0.00 -37923.49
26 Obtaining approval from PESO (Petroleum and Explosives Safety Organization) for HAZARDOUS CLASSIFIED (local/imported) equipment 1 1 0 196,803.0 -3.50% 189,915 189,915 0.00
such as motors, local control panels, junction boxes & misc. equipment, etc. based on the type test certificates made available from the
equipment/sub vendor supplier, submission of application to statutory authorities like Electrical inspectorate / OISD Authorities
/ Factory Inspector as applicable, necessary fee, all test certificates, equipment drawings in required volume, interaction with the authority,
perusal of approval and obtaining necessary approval certificate before the energization of equipment/ substation as per specification of this
tender and direction of Engineer in charge. -
27 Supply of mandatory spare for following electrical equipment as well as mandatory spare applicable for electrical equipments which
are in contractors scope of supply shall be supplied by Contractor.
27.1 LED light Fixtures. 1 1 0 107,899.2 -3.50% 104,123 104122.71 0.00
27.2 LCS (local control station)/push button station 1 1 0 14,382.6 -3.50% 13,879 13879.19 0.00
27.3 Lighting JB 1 1 0 71,393.9 -3.50% 68,895 68895.10 0.00
shall be measured). -
28.1 Excavation and backfilling of trenches in all types of soil except rock. - Supply and spreading of approved fine river sand/stone dust in 500 500 0 470.0 -3.50% 454 226,785 0.00
cable trenches, including all labour and materials, specifications of this tender and directions of Engineer-in-Charge. - Stone dust. -
28.2 Supply and spreading of approved second class bricks of 75 mm thickness in cable trenches for cable protection, including all labour and 1000 1000 0 15.7 -3.50% 15 15,119 0.00
materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. (Actual area of laid brick
surfaces shall be measured). - Bricks. -
28.3 Providing and laying plain cement concrete for all depths below and up to a plinth level in foundations including tamping, ramming,
vibrating, curing, shuttering etc. all as specified in any shape, position, thickness and finishing the top surface rough or smooth as
specified and directed, including supply of all materials and all complete for concrete of M-15 grade with 20 mm and down size graded
crushed stone aggregates, including all labour and materials, as per approved drawings, specifications of this tender and directions of
Engineer-in-Charge. -
Plain cement concrete. - 10 10 0 6,475.8 -3.50% 6,249 62,492 0.00
28.4 Supply, fabrication and installation of 6 mm thick M.S. chequered plate for covering floor cut- outs/cable trenches etc., including all
labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. -
6 mm thick M.S. chequered plate. - 10 10 0 6,893.6 -3.50% 6,652 66,524 0.00
28.5 Making through and through cut outs in pockets of size 150 mm dia in the RCC floor/walls of trenches/buildings of thickness upto 10 10 0 223.8 -3.50% 216 2,160 0.00
200mm for facilitation cable entries using concrete cutting machines including all labour and materials as per approved drawings,
specifications of this tender and directions of Engineer -in-charge -
A.3.4.1 Dia (outer) 160 mm , Piping Material Class 1 r.m 50 150 100.00 867 -3.50% 837 125,498 83665.50
C.1.1.2 Same as item C.1.1.1 but depth from upto 1.5m to inclusive 3.0m depth cu.m 291 800 509.00 378 -3.50% 365 291,816 185667.93
Providing and installing approved type of "SHORING AND STRUTTING" by close timbering method for all depths to
C.1.2.2 retain earth including dismantling and removal of the same etc. from site after completion of work etc. all complete sq.m. 20 400 380.00 735 -3.50% 709 283,710 269524.50
as directed by E.I.C.
Backfilling
BACKFILLING after execution of the WORK to proper grade and level with available excavated earth within refinery
premises including breaking clods, laying at all depths and heights in layers of thickness not exceeding 15 Cms. watering,
C.1.3.2 rolling and ramming by manual methods/ mechanical compactors to achieve 95.11% laboratory maximum dry density, Cu.m 100 6,000 5900.00 410 -3.50% 396 2,373,900 2334335.00
dressing, trimming etc. in foundations, plinths, trenches, pits etc. disposal upto a lead of 100m surplus earth, if any,
etc., complete as per drawings, specifications and as directed by Owner/Consultant..
TRANSPORTATION OF EARTH WILL BE IN CONTRACTOR SCOPE OF WORK
Transporting and disposing the SURPLUS EARTH AND DEBRIS including shrubs and vegetations from construction
area beyond the initial LEAD OF 100 MTRS AND UPTO & INCLUSIVE OF 1.0 KM including re-excavating the deposited
soil excavated earlier, transportation, loading, unloading, laying at all depths and heights, stacking, levelling and dressing
C.1.4.1 cu.m 100 2,500 2400.00 335 -3.50% 323 808,188 775860.00
both the area (viz. from where the earth is transported and where it is deposited) to required levels and slopes
complete with all lifts as directed by Owner/Consultant. For carting on the basis of truck measurements (volume of truck
reduced by 35.11% for voids).
"Designing, supplying and fixing rebars in already cast concrete, including drilling, cleaning hole with air blow-out
& wire- brush and injecting odourless Rebar Anchor Adhesive HILTI HIT - RE 500 V3 or approved equivalent make
Chemical, packed in dual foil, with the help of dispenser into a hole of diameter and depth as per manufacturer's
C.1.10.1 specification, at all levels & locations for high strength deformed steel reinforcement bars of dia. upto 12 mm of Grade Each 27 615 588.00 681 -3.50% 657 404,156 386413.02
Fe500D (conforming to IS:1786), DESIGNED FOR FULL TENSILE ANCHORAGE, including testing (as per manufacturer's
recommendations), adjusting and making good any damage done to the structure etc. all complete as specified and
directed. SUPPLY OF ALL MATERIAL IN CONTRACTOR'S SCOPE EXCLUDING REINFORCEMENT BARS.
"Designing, supplying and fixing rebars in already cast concrete, including drilling, cleaning hole with air blow-out
& wire- brush and injecting odourless Rebar Anchor Adhesive HILTI HIT - RE 500 V3 or approved equivalent make
Chemical, packed in dual foil, with the help of dispenser into a hole of diameter and depth as per manufacture
C.1.10.2 specification, at all levels & locations for high strength deformed steel reinforcement bars of dia. 16 mm & 20 mm Each 25 50 25.00 939 -3.50% 906 45,307 22653.38
of Grade Fe500D (conforming to IS:1786), DESIGNED FOR FULL TENSILE ANCHORAGE, including testing (as per
manufacturer's recommendations), adjusting and making good any damage done to the structure etc. all complete
as specified and directed. SUPPLY OF ALL MATERIAL IN CONTRACTOR'S SCOPE EXCLUDING REINFORCEMENT BARS. "
Final Rate Cost of Additional
Item No. Unit Qty. Revised qty Addtion /Deletion Rate as per PO placed Discount Total Revised Cost
(INR) Items
Supplying, Fabricating and Erecting in position (fabricating at fabrication shop/ yard located outside plant boundary),
mock Assembly (including testing & examining), Storing, Transporting and Delivery of bolted (including supply of
connection bolts) and/ or welded Fabricated Structural Steel of Grade as per design drawing and conforming to IS:2062,
including all builtup sections/ compound sections made out of rolled sections and/ or plates/ bent plates in all types of
structural frameworks, cutting to required size, straightening/ bending if required, edge preparation, cleaning,
S.1.1 preheating, bolting/ welding of joints, (including sealing the joints of box sections with continuous welding and plugging t 415 575 160.00 105,296 -3.50% 101,611 58,426,118 16257702.40
any open ends & holes of box sections), finishing edges by grinding, including preparation and submission of detailed
fabrication drawings, preparing the surface for painting by shot blasting to SA 2 1/2 (SSPC-SP-10) and applying pre-
erection/ shop primer (1 coat of inorganic Zinc silicate @ 75 micron DFT) as per Specification (or as per Job
Specification, wherever applicable) after fabrication and erection for heights 0.00m to 15.00m or below plinth etc., all
complete. Connection bolts shall be of Grade 8.8 (Galvanised). SUPPLY OF ALL MATERIAL IN CONTRACTOR'S SCOPE
Supplying, handling, transporting to site of work and fixing approved MECHANICAL ANCHOR FASTENERS M.S. bolts of
Grade 5.8 or more of Hilti or approved equivalent make, GALVANIZED with minimum thickness of 5 microns (approved
for use in cracked concrete), of 16mm dia at specified positions on concrete floors, roofs, beams (sides and bottom),
S.1.2.8.2 walls, columns etc. according to manufacturer's specifications including all accessories like nuts, washers etc. of required Each 25 50 25.00 1,562 -3.50% 1,507 75,367 37683.25
size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air
blowout & wire-brush, and making good any damage done to the structure etc. all complete for all heights, depths and
locations as specified and directed by E.I.C.
Supplying, handling, transporting to site of work and fixing approved CHEMICAL ANCHOR FASTENERS consisting of M.S.
threaded rod of Grade 5.8 of Hilti or approved equivalent make, GALVANIZED with minimum thickness of 5 microns and
chemical (approved for use in cracked concrete), packed in flexible chemical foil or dual foil type, to be used with the help
of dispenser, of 16mm dia. at specified positions on concrete floors, roofs, beams (sides and bottom), walls, columns etc.
S.1.2.9.1 Each 25 276 251.00 1,661 -3.50% 1,603 442,391 402319.12
according to manufacturer's specifications including all accessories like nuts, washers etc. of required size., testing,
necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire-
brush and making good any damage done to the structure etc. all complete for all heights, depths and locations as
specified and directed by E.I.C.
To surface of structural steel fabricated out of RSJ angles, channels, builtup sections, etc. & also Parallel Flange
S.1.2.12.1 t 415 515 100.00 10,911 -3.50% 10,529 5,422,494 1052911.50
sections
Demolishing BRICKWORK (taking all necessary safety precautions) for all depths below plinth level including supply of all
tools and tackles, necessary scaffolding, propping, underpinning, cleaning and stacking of serviceable material, disposal of
D.2.1 unserviceable material to spoil heaps anywhere within the plant boundary, all complete as specified and directed. cu.m 25 185 160.00 987 -3.50% 952 176,204 152392.80
(Excavation &
backfilling shall be paid separately under relevant items).
Demolishing PLAIN CEMENT CONCRETE work (taking all necessary safety precautions) for all depths below plinth level
including supply of all tools & tackles, necessary scaffolding, propping, underpinning etc. disposal of unserviceable
D.4.1 material to spoil heaps ANYWHERE OUTSIDE THE PLANT BOUNDARY, all complete as specified and directed. Disposal cu.m 114 233 119.00 2,018 -3.50% 1,947 453,737 231737.03
areas outside plant Boundary to be arranged by the contractor. Royalty as applicable for disposal outside plant limits to
be borne by the Contractor. (Excavation & backfilling shall be paid separately under relevant items).
Providing ,concrete M15 encasing to underground pipes on all sides square/circular including shuttering etc. complete as
M.1.42 per cu.m 5 15 10.00 8,996 -3.50% 8,681 130,217 86811.40
drawing,specification & as directed by owner/consultant.
NOTES:-
1 Contractor to visit site prior to quote for familiarisation with site conditions ( i.e. detailed site studies to decide the type
2 This is an item rate tender and quantities are tentative. The Contractor's unit rates quoted shall not change for any
3 The schedule of Rates shall be read with all other sections of this bidding document.
4 The contractor is deemed to have studied the drawings, specifications & details of work to be done within the time
5 All items of work mentioned in the schedule of Rates shall be carried out as per the drawings, specifications,applicable
6 Material shall be of good quality and purchased from approved source ; contractor shall get it approved from engineer in
7 Work shall be carried out as per latest construction drawings, specifications & carried out to the satisfaction of engineer-
8 Fabrication drawings for structural steel work shall be prepared by contractor before shutdown period as required by
9 Bar bending schedule shall be prepared by contractor.
10 Contractor to take care of safety of surrounding people / machinery.
11 Ready mix concrete shall be used for concrete grade M-20 and above.
12 Contractor to submit the design mix for approval prior to use in concreting
13 The payment will be made as per actual work carried out & will be certified by the Engineer- in- charge
14 The demolition & dismantling activity of brick masonry & structural steel respectively and compaction of backfilled soil
15 Any conflicts , doubts shall be highlighted, discussed & sorted out with the Engineer- in- charge prior to carrying out the
Final Rate Cost of Additional
Item No. Unit Qty. Revised qty Addtion /Deletion Rate as per PO placed Discount Total Revised Cost
(INR) Items
16 Adequate fall protection measures at locations of excavation , at elevated openings during construction stage shall be
17 Payment length for piling shall be measured below the cut off level. No Payment will be considered for concrete above
18 Contractor to work with care mainly in the existing areas and all necessary precautions needed shall be taken by the
19 The modifications/dismantling of work in existing facility shall be done after getting approval from Owner/PMC.
20 Contractor should make use of reinforcement bar locator of approved make , as required for repair work as directed by
21 Only steel scaffolding permitted. Scaffolding shall be preferably cup-lock type or any latest type.
22 Power & Water supply will be supplied at one location by IOCL . Contractor has to make necessary arrangement for the
23 DEMOLITION:- (As applicable)
i) Please note that the contractor will have to clear & dispose all the unserviceable material got from the demolished
ii) The contractor shall use less vibration demolition tools /equipment's during the demolition work. Signage's (Safety
iii) The work includes identification of required working underground lines (connected to the structures which are to be
iv) Temporary Hard material barricading at site as per site requirement for safety measures includes painting, arrangement
v) Nylon net Horizontally with supports for open area all around the building/inside the building for elevated demolition
vi) Temporary Steel pipe (hard material) handrailing shall be installed at openings at site as per site requirement for safety
vii) Contractor should submit load test certificates of all equipment's/machinery to be used in site . Contractor shall arrange
24 All excavations shall be carried out after prior approval of Owner / consultant.
25 Regular site cleaning is mandatory and scrap and other un-serviceable material to be removed from site on regular basis.
26 RCC breakage measurement to be paid extra
COMPOSITE TENDER
IOCL, Haldia
Catalytic De-waxing Unit and allied facilities of CDWU-II Project SCHEDULE OF PRICE FOR PILING WORKS 44AD2800
Cost of
Rate as per Total revised
Item No. Description Unit Qty. Revised qty Additon / Deletion Discount Final Rate Additional
PO Cost
Items
2.0 Construction of Piles
Bored Cast-In Situ Piles:-
Designing, Mobilisation & demobilisation, providing and constructing Vertical Bored Cast-In-Situ Piles including boring by "power
operated rotary auger" OR "tripod & winch operated DMC Chisel" & temporary casing of uniform diameter with lifting hook at top
& with shoe at bottom for displacing soil. Boring using Bailer at initial depth & further by cutting tool / chisel to proper location and
alignment through all kinds of soil, (incl. fill, loose/dense sand and silt, soft/firm clay with stray gravels) to required hard strata
approved by engineer in-charge. Rigs shall be tyre or crawler mounted. Jetting to be done if required. Concreting by Tremie using
M30 concrete with ordinary portland cement; minimum cement content 400 kg/cu.m. & W.C. ratio not exceeding 0.45 with 20 mm
downgrade aggregate & approved admixture as required as per mix design.
Providing, assembling, placing, transporting, straightening, cleaning, cutting, bending Reinforcement as per design & tying it in
position by binding wires (16 SWG) & ensuring exposed reinforcement to be kept clean & intact with cement wash etc. for basic
pile length. Casting piles including chipping & building up where necessary to attain specified cut-off level (Concreting to be
done min. 1.0 m above cut-off level & the rate quoted by contractor to account for it) complete as per drawing, specification & as
directed by owner/consultant (Incl. conducting SPT'S in pile bore hole which shall have the basis of
termination critieria).
2.0 i) Boring 500 mm dia. piles (measured from ground level) in all kind of soils, sand. Rm 352 1909 1557 3,844 -3.50% 3,709 7,081,359 5,775,629
2.0 ii) Boring 600 mm dia. piles (measured from ground level) in all kind of soils, sand. Rm 704 0 -704 4,811 -3.50% 4,643 0 -3,268,401
2.0 iii) Concreting in 500 mm dia. pile as per IS:2911 (concrete measured from cut-off lvl to toe of pile). cu.m 70 280 210 -3.50% 0 0 0
2.0 iv) Concreting in 600 mm dia. pile as per IS:2911 (concrete measured from cut-off lvl to toe of pile). cu.m 199 0 -199 -3.50% 0 0 0
2.0 v) High yield strength deformed bars Fe 500D conforming to IS:1786 (All reinf. Bars shall be TMT bars). t 35 50 15 73,433 -3.50% 70,863 3,543,142 1,062,943
3.0 Pile testing ( Including report preparation & Submission)
3.0 i) Carrying out specified initial cyclic load test on test piles as specified in IS : 2911, including all plants, equipments, Kentledge
i) 500 mm dia. Nos 1 1 0 127,214 -3.50% 122,762 122,762 0
ii) 600 mm dia. Nos 1 0 -1 127,214 -3.50% 122,762 0 -122,762
3.0 ii) Same as item 3.0 i), but lateral load test on test piles.
i) 500 mm dia. Nos. 1 1 0 77,742 -3.50% 75,021 75,021 0
ii) 600 mm dia. Nos 1 0 -1 77,742 -3.50% 75,021 0 -75,021
3.0 iii) Same as item 3.0 i), but pull out test on test piles with maximum pull out load of 2.0 times the safe pull out capacity.
i) 500 mm dia. Nos. 1 1 0 87,165 -3.50% 84,114 84,114 0
ii) 600 mm dia. Nos 1 0 -1 87,165 -3.50% 84,114 0 -84,114
3.0 iv) Carrying out routine vertical load test on working pile as specified in IS : 2911, including all plant equipments,
i) 500 mm dia. Nos. 1 1 0 101,889 -3.50% 98,323 98,323 0
ii) 600 mm dia. Nos 1 0 -1 101,889 -3.50% 98,323 0 -98,323
3.0 v) Same as item 3.0 iv), but lateral load test on working piles.
i) 500 mm dia. Nos. 1 1 0 64,785 -3.50% 62,518 62,518 0
ii) 600 mm dia. Nos 1 0 -1 64,785 -3.50% 62,518 0 -62,518
3.0 vi) Carrying out Sonic Integrity Tests on Working piles Nos. 2 6 4 2,297 -3.50% 2,217 13,300 8,866
3.0 iv) Excavation in all sorts of soil, soft / hard including soft / hard murrum, but excluding soft and hard rock, using excavators if
(i) Up to 2.5 m depth below FGL cu.m -
3.0 v) Carting away within the Refinery Premises up to a distance of 5 Kms. cu.m -
3.0 vi) Carting away outside the Refinery Premises. cu.m -
COMPOSITE TENDER
IOCL, Haldia
2 Structural steel Supports with suitable Pedestals for Mounting Outdoor Fire Hose Box Kg 100 113 -3.50% 109 10,939 11,336
3 Civil Pedestal of suitable Size for mounting Fire Hose Cabinets Nos 4 1,800 -3.50% 1,737 6,948 7,200
IOCL, Haldia
Catalytic De-waxing Unit and allied facilities of CDWU-II Project SCHEDULE OF PRICE FOR SPECIAL ITEMS (FIREPROTECTION)
44AD2800
Total Revised
Item No. Description UOM Quantity Rate (INR) Discount Final Rate Amount (INR)
Cost
Gun Metal body Single headed Hydrant Valve as per IS 5290 Type A with 3" Flanged Inlet Flat Face, to ASME B 16.5
1 Nos. 2 4,327 -3.50% 4,175 8,351 8,654
and outlet of 2-1/2” Instantaneous coupling connection with Blank cap and chain. (BIS/UL/FM approved)
Double door outdoor Mild steel sheet (18SWG thk) Fire Hose box suitable to accommodate 2 Nos. of Fire Hose
2 along with Branchpipe Nozzles complete with all suitable accessories and Painted with Fire red paint as per IS: 5 Nos. 2 2,197 -3.50% 2,120 4,240 4,394
over two coats of Zinc chromate primer on outer surface.
Non percolating Flexible synthetic fibre (TYPE B) 63 mm Diameter X 15 Mtrs Long Fire Hose fitted with suitable
3 Nos. 4 12,007 -3.50% 11,587 46,346 48,027
instantaneous couplings as per IS : 636 and IS : 903. (BIS/UL/FM approved)
Gun Metal based Triple Purpose Nozzle with Chromium plated finish as per IS : 2871 and OISD -115 with suitable
4 Nos. 2 4,062 -3.50% 3,919 7,839 8,123
instantaneous inlet of 63 MM Dia (BIS/UL/FM approved)