Professional Documents
Culture Documents
W
PHILIPS MEDICAL SYSTEMS
RECORD OF SYSTEM PROGRAMMING 2
DigitalDiagnost
VRïE RECORD OF DEFAULT USER PROGRAMS 3
Level 0
Documentation
RECORD OF RECOMMENDED SETTINGS 4
Part 2 (SRM)
SERVICE INFORMATION 6
DMC Hamburg
This document and the information contained in it is proprietary
and confidential information of Philips Medical Systems
(”Philips”) and may not be reproduced, copied in whole or in part,
CABLE AND EARTH DIAGRAMS 9
adapted, modified, disclosed to others, or disseminated without
the prior written permission of the Philips Legal Department.
This document is intended to be (a.) used by customers and is
licensed to them as part of their Philips equipment purchase or
(b.) used to meet regulatory commitments as required by the
FDA under 21 CFR 1020.30 (and any amendments to it) and
other local regulatory requirements. Use of this document by
unauthorized persons is strictly prohibited.
Printed in Hamburg
PACKING LIST 10
Federal Republic of Germany
(06.0)
2004 Koninklijke Philips Electronics N.V.
ALL RIGHTS RESERVED
Blank page
Blank page
Section 11:
Contents
1. General information
2.
1-1...1-2 (06.0)
General information
1. Introduction
2. Abbreviations
Abbreviation Explanation
General
AGenT Access Generator Tool
APR Anatomically Programmed Radiography
BIST Build In Self Test
BWLM Basic Worklist Management
BWS Bucky Wall Stand
CAN Control Area Network
COM Serial port
DICOM Digital Imaging and Communication in Medicine
DiDi DigitalDiagnost
FCO Field Change Order
FRU Field Replaceable Unit
MPPS Modality Performed Procedure Step
MSB Mini System Bus
MTP Move To Position
PCB Printed Circuit Board
PDU Power Distribution Unit
PCR Philips Computerised Radiography
PMS Philips Medical Systems
POST Power On Self Test
RGDV Registration Device (auxiliary unit)
UPS Uninterruptible Power Supply
Abbreviation Explanation
Documentation
SMI System Manual Installation (Level 0 Documentation Part 1)
SRM System Reference Manual (Level 0 Documentation Part 2)
System names
DigitalDiagnost TH table and optional VM or VS wall stand
DigitalDiagnost VM VM wall stand and optional a TH-S table or TF-M trolley
DigitalDiagnost VM Compact VM Compact wall stand and optional a TF-M or Traumob-X trolley
DigitalDiagnost VR VS wall stand and optional a TF-M trolley
Subsystem names
CS 2/4 Ceiling Suspension (2 = short longitudinal carriage / 4 = long longitudinal carriage)
FS fix Floor Stand fixed
TH Table Height adjustable
TH-S Table Height adjustable Single side suspended
TF-M Trolley Fixed Moveable
TH-M Trolley Height adjustable Moveable
VM Vertical Multipurpose stand moveable
VM Compact Vertical Multipurpose stand fixed
VS Vertical stand with fixed bucky module
VS tilting Vertical stand with tiltable bucky module
Unit names
BUF Bucky Unit Family
RO Rotalix tube (RO 1750)
SCU Segment control unit
SRO Super Rotalix tube (SRO 0951, SRO 2550, SRO 33100)
Contents
2.
Contents
NOTE
These DigitalDiagnost specific program settings are already done in the factory !
Data Set B
Used for tomo no yes no no no
Used for flouroscopy no no no no no
CT add on no no no no no
NOTE
These DigitalDiagnost specific program settings are already done in the factory !
correction factor 1
3. APR programs
NOTE
These DigitalDiagnost specific program settings are already done in the factory !
NOTE
For the data transfer the CAN bus cables EZX42, EZX43 and the signal bus EZX23 must be disconnected !
After successful download reconnect the CAN bus cables EZX42, EZX43 and the signal bus EZX23.
Restart the generator.
NOTE
The APR-files in the following table can only be used in the system configuration DigitalDiagnost VR-E with
BuckyDiagnost FS fix !
NOTE
For the data transfer the CAN bus cables EZX42, EZX43 and the signal bus EZX23 must be disconnected !
After successful download reconnect the CAN bus cables EZX42, EZX43 and the signal bus EZX23.
Restart the generator.
J
Contents
1.
Contents
2.
Contents
1. DigitalDiag. TH/VR/VM/VM Comp. sys. with one ceil. susp. CS or fl. stand FS . . 4ï2
1.1. Control handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï2
1.2. Tracking controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï2
1.3. Longitudinal motor controller CS2/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï3
1.4. Alpha motor controller CS2/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï3
1.5. Bucky tray motor controller TH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï4
1.6. Nicol Collimator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï4
1.7. Bucky controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï5
2. DigitalDiagnost TH with SECOND CS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï6
2.1. Control handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï6
2.2. Tracking controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï6
2.3. Tomo controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï7
2.3.1. Longitudinal motor controller CS2/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï7
2.3.2. Alpha motor controller CS2/4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï7
2.3.3. Bucky tray motor controller TH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï8
2.4. Nicol Collimator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï8
2.5. Bucky controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï9
2.6. X-Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4ï9
Jumper UE2 W1
Pins 2ï3 bridged (room 1)
CAN node name: CSU_HD1
X9
UE2 H1
3
2
1
W1 W2 W3
Jumper UAD X7
Pins 1, 2, 3, 4, 6, 7 bridged
Pins 5, 8 open
CAN node name: SLSCSD1
X6
Jumper
UAD
X7
1
1
Jumper UBN2 X7
Pins 1, 2, 3, 4, 5, 6, 7, 8 bridged
no pins open
CAN node name: TomoDv1
X6
Jumper
UBN2
X7
1 1
Jumper UFN1 X7
Pins 1, 2, 4, 5, 6, 8 bridged
Pins 3, 7 open
CAN node name: AlphDv1
X6
Jumper
UFN1
X7
1 1
Jumper SAN1 X7
Pins 1, 2, 3, 4, 5, 6, 7 bridged
Pin 8 open
CAN node name: TrayDv1
X6
Jumper
SAN1
X7
1 1
The jumper LA1 W1 is located behind the ruler side plate in the collimator.
Jumper LA1 W1
Pins 1ï2 bridged (room 1)
CAN node name: BLD1DV1
X6
1
1
2 W1
LA1 3
MP1 ï
MP2 ï
X2
MP3 ï
MP4 ï
Jumper SZ1 S1
Dip-switch 1 set to closed (room 1)
Dip-switch 2 set to open (CAN slave)
Dip-switch 3 set to closed (X-Scope)
CAN node name: RADCtl1
O
P
E
N
SZ1 8
7
6
5
4
VTï100 3 XïScope
slave 2 master
room 2 1 room 1
S1
NOTE
All settings are only applicable in a DigitalDiagnost system with two ceiling suspensions (bucky controllers) !
X9 X9
UE2 H1 UE2 H1
3 3
2 2
1 1
W1 W2 W3 W1 W2 W3
X6 X6
8 8
Jumper Jumper
UAD UAD
X7 X7
1 1 1
1
Jumper UBN2 X7
Pins 1, 2, 3, 4, 5, 6, 7, 8 bridged
no pins open
CAN node name: TomoDv1
X6
Jumper
UBN2
X7
1 1
Jumper UFN1 X7
Pins 1, 2, 4, 5, 6, 8 bridged
Pins 3, 7 open
CAN node name: AlphDv1
X6
Jumper
UFN1
X7
1 1
Jumper SAN1 X7
Pins 1, 2, 3, 4, 5, 6, 7 bridged
Pin 8 open
CAN node name: TrayDv1
X6
Jumper
SAN1
X7
1 1
X6 X6
1 1
1 1
2 W1 2 W1
LA1 3 LA1 3
MP1 ï MP1 ï
MP2 ï MP2 ï
X2 X2
MP3 ï MP3 ï
MP4 ï MP4 ï
O O
P P
E E
N N
SZ1 8
SZ1 8
7 7
6 6
5 5
4 4
VTï100 3 XïScope VTï100 3 XïScope
slave 2 master slave 2 master
room 2 1 room 1 room 2 1 room 1
S1 S1
2.6. X-Scope
Differences in the programming to a DigitalDiagnost system with one ceiling suspension:
Contents
1. Read me first
2.
Read me first
Read me first
System status report for manufacture and field installation
Introduction:
The Bucky system is adjusted in the factory according to the actual service documentation.
Contents:
NOTE
The requirements listed in this section may differ from the requirements of national regulations (e.g. RÖV).
Measured values outside this status report must be inside the limitation of national regulations.
factory field
side side
2. Programming and adjustment
The mechanical installation must be done in order of the installation manual.
For adjusting and programming fill out the attached list.
factory field
side side
Collimator + BuckyDiagnost CS 2/4, FS
Type of collimator
Manual - Automatic -
Manual + Automatic
Power supply for coll. bulb = ............ V (11...12 V) (measured on bulb) -
The maximum deviation between light and X-ray is allowed to be as follows at all four edges. (see table)
automatic manual
Tol. +5 / ï3 mm +9 / ï3 mm
The maximum deviation at the top/bottom edge and left/right edge is 5 mm.
In case the light field is smaller than the X-ray field, use minus signs.
measured deviations
Top : mm Bottom : mm Diff. : mm
Left : mm Right : mm Diff. : mm
factory field
side side
BuckyDiagnost CS 2/4, FS
All mechanical movements are in order to the internal checklist (factory side). -
All functions are in order to the operator manual. - -
Lamp functions ï breaks ï catches ï end stops ï cabling. - -
The detents must be programmed with X-Scope -
BuckyDiagnost CS 2/4:
The sensing function is tested
in longitudinal direction - transversal direction - - -
BuckyDiagnost FS:
The sensing function is tested - -
Tracking
BuckyDiagnost CS 2/4
TraumaDiagnost
(not implemented)
factory field
side side
2. Programming and adjustment
The mechanical installation must be done in order of the installation manual.
For adjusting and programming fill out the attached list.
BuckyDiagnost CS height
(This value is depending on your room height and therefore also adjusted on field side).
min. = ............ mm -
max. = ............ mm
NOTE
factory field
side side
Tomo + TH and Tomo 2 + TH2
Angle Tomo time in s Layer height in mm Layer height deviation " 3mm
40_ 1.2 45
40_ 1.2 130
40_ 1.2 199
NOTE
The layer height is adjustable with ”tid” under X-Scope. tid= .......... mm -
tid nominal = 65 mm Range of adjustment = 65 ... 75 mm
tid ACL nominal= 70 mm Range of adjustment = 70 ... 80 mm
tid flat detector = 78 mm Range of adjustment = 70 ... 90 mm
factory field
side side
jAj ï jBj = v 6 mm
A = .......... mm
B = .......... mm
Maximum extent of the X-ray beam
jAj + jBj = v 40 mm Center beam
A ........ mm B ........ mm
Symmetry (spotcheck) - -
The symmetry of the X-ray beam with Tomo is tested by
layer height = 130 mm SID = 115 cm Tomo angle = 40_ 1,2 sec = Exposure time
jCj ï jDj = v 5 mm
C = .......... mm
D = .......... mm
C D
..........mm ..........mm
factory field
side side
2. Programming and adjustment
The mechanical installation must be done in order of the installation manual.
For adjusting and programming fill out the attached list.
AMPLIMAT function -
All mechanical movements and functions are in order to the operator manual. -
Nominal value = 120 ms "4ms -
No grid lines visible by exposure time tw3 msec.
factory field
side side
3. General / Safety aspects
System configuration:
Generator OPTIMUS 50 - 65 - 80 -
Room 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Room 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Room 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NOTE
Contents
3.
Country :_____________________
City :_____________________
Customer :_____________________ Room: _______________
Additional material sent with the defective DETECTOR ( mark like this : )
The detector
consists of 4
panels.
Examples:
There are 13
readout amplifiers
on each panel.
Sketch:
Comment
Detector Ser# : ..................
Date : ..................
sketch
X
Logo Address
Logo Address
DigitalDiagnost
System labelling
Contents
2.
NOTE
All other combinations of software, firmware and PCB are not tested / released and will lead to malfunction or
do not work at all.
All rel 1.3 system in the field were upgraded to rel 1.3.1 (FCO 712 00 005) and all rel 1.4 systems were upgraded to
rel 1.4.1 (FCO 712 00 009).
Release
First delivery from factory Aug 2002 May 2003 May 2004 Oct 2004 May 2005 Xxx 2006
CAN 1.5
Tracking Controller (CS + FS)
Motor 1.5
NOTE
Please be aware of the different jumper- and DIP-switch settings between the PCB- and related firmware
version !
J
4512ï983ï10831 CSIP Level 0 (06.0) 7ï1
2005 Koninklijke Philips Electronics N.V.
ALL RIGHTS RESERVED
Grid data sheet DigitalDiagnost VR-E with FS Fix
Contents
2.
Absorber material:
Grid expose factor B: (Buckyïfactor)
Q+K Tp
The interspace material is fiber
Table 2
Ratio 6 : 1 Grid Width
f0 18 cm 24 cm 30 cm 36 cm 43 cm
80 cm 50 ï 196 cm 55 ï 144 cm 59 ï 124 cm 62 ï 114 cm 64 ï 106 cm
100 cm 57 ï 386 cm 64 ï 225 cm 69 ï 180 cm 73 ï 159 cm 76 ï 145 cm
140 cm 69 ï ∞ cm 79 ï 630 cm 86 ï 371 cm 92 ï 291 cm 98 ï 247 cm
180 cm 77 ï ∞ cm 90 ï ∞ cm 100 ï 90 cm 108 ï 540 cm 116 ï 407 cm
Contents
5. Connection diagrams
6. Earthing diagram
9.
E
ME C Work- Modem Uninterruptable
station Telephone power supply
S line (for Workstation only)
S UPS
C
U (option)
Emerg.
off
EZX4:2
MEX
L2 switched bn
T1 ENK2:3/L2
L2´ continuous power blk
T2 ENF2:4/T2
T3
N bl
N ENX1101
SX
L2 switched bn
T1 SX50
earth lekage L2´ continuous power blk
T2
circuit breaker L2 switched bn 1 SX51
T3 power supply
N bl da L2´ continuous power blk 3 SF1
N SX52
N bl 5
mains fuses Surge arrester
mains feeder (option) SX53
L1 L1 L1
ENF1:1 da power supply VPX53 M3
L2
L2 L2 M3 SX54
L3 WN ENF1:3 * A neutral conductor is not
UZX9
L3 L3 ENF1:5 required if the mains transformer M3f da power supply SX55
N 9890 000 02301 is ordered
N* N ENX1101
from * SX56
supply
tube housing
EX1100 XA 1
1 U
1 U 1 1
2 V
2 V 2 2
XA 3 W
3 db stator cable W
3 3
X-ray tube
D9f VP3X2
R
SUN workstation
A2 05-09-15 Ost./Kö
DigitalDiagnost VR-E
with BuckyDiagnost FS Fix
OPTIMUS RAD
System connection diagram
E
ME C Work- Modem Uninterruptable
station Telephone power supply
S line (for Workstation only)
S UPS
C
U (option)
DigitalDiagnost VR-E
with BuckyDiagnost FS Fix
OPTIMUS RAD
System earthing diagram
UAD
Servo tracking
X4 X3
DigitalDiagnost
VE/VT (moveable)
UE
Control
handle
Optimus generator
LA1
X9 X10 Collimator UF
X1 X11 X3
VP3
EZ X43 X42 X3
R X2
R
S
X3 X2
SZ1 Bucky
controller
A3 05-08-24 Schr.
DigitalDiagnost VR
with DigitalDiagnost VE/ VT (moveable)
CAN connections
SA film plane 1
30
15 15
UA column (bucky DIAGNOST Floor Stand) 15
UB ceiling crane longitudinal carriage (bucky DIAGNOST CS)
65 15 43 38 38
UZ ceiling crane transverse carriage (bucky DIAGNOST CS)
43
VE/VT vertical DIAGNOST
VP wcb vertical DIAGNOST 12
WS wallstand
XA X-ray tube crimp pin male 2422 034 11636
wcb wall connection box 11BNC-connector crimp pin female 2422 034 11632
2432 020 00272 distance piece (M3, 11mm) 2422 034 20331
24.5 14.5 L2
D37 D37 D-SUB 37 pins
28 28
L3 5 x 25mm 2 28
D25 D25 D-SUB 25 pins
D15 D15 D-SUB 15 pins
N crimp pin female crimp pin male
2422 015 14048 2422 034 17788
D9 D9 D-SUB 9 pins
MD6 MD6 MINI-DIN 6 pins
cable delivered
Cables
A68 A68 AMPLIMITE 050 68 pins
Type Description Diameter Codenumber
9f 9m gender changer 9 pins MINI-DIN 6 pin
Connection blocks da 3+1 x 1.38 mm2 8.0 mm 0722 207 03044
db 3 x 1.3 mm2 screened + yl 9.2 mm 0722 215 02054
MEX designation of connection block
1 1 dc 2 x 0.8 mm 2 6.2 mm 0722 300 01011
2 2 connection block
3 3 dd 5x2 x 0.22 mm2 screened 7.4 mm 0722 215 62001
4 4 screw junction
5 5 50 de 12x2 x 0.22 mm2 screened 9.6 mm 0722 215 51007
terminal number
df 10 x 0.5 mm 2 7.3 mm 4512 100 66451
dg 10 x 0.5 mm2 screened 7.8 mm 0722 997 07248
Earthing dh 8x2 x 0.22 mm2 screened + yl 8.4 mm 0722 215 33008
earth connection block
dk 8 x 0.75 mm 2 screened 9.6 mm
MEX designation of connection block
2 16 mm2
dm 6x2 x 0.75 mm2 screened 12.6 mm
5 25 5 earthing strip
dn 2x2 x 0.22mm2 screened com.chan.
A3 03-05-12 DP/Kö
Contents
1.