Professional Documents
Culture Documents
DESCRIPTION OF
STRUCTURAL CALCULATION
04/2021
DESCRIPTION OF STRUCTURAL CALCULATION
Page 2/40
DESCRIPTION OF STRUCTURAL CALCULATION
EN-1992-4 Eurocode 2. Design of concrete structures. Design of fasterning for use in concrete/ Tiêu
chuẩn châu Âu Eurocode 2, thiết kế kết cấu bê tông. Thiết kế hệ neo trong bê tông.
Façade project specification. / Bảng tiêu chí kỹ thuật hệ mặt dựng của dự án
Page 3/40
DESCRIPTION OF STRUCTURAL CALCULATION
The total self-weight shall be used in combination with wind load and other applied loads in the design of all
members/ Tải trọng bản thân được tổ hợp với tải gió và các tải khác trong thiết kế.
Design windload is calculated base on Viet Nam building code TCVN 2737-1995 “Load and effect – Design
Standard” which show more detail in annex 2/ Tải gió thiết kế cho phương án đề xuất được tính toán dựa trên Tiêu
Chuẩn Việt Nam 2737-1995 “Tải trọng và tác động – Tiêu chuẩn thiết kế”, xem chi tiết trong phụ lục 2.
+ Tải trọng gió tác dụng tại tầng 18
Page 4/40
DESCRIPTION OF STRUCTURAL CALCULATION
The seismic presssure applied to the module is equal to 0.24 of the element weight/ Áp lực tải động
động đất tác dụng vào module bằng 0.24 lần khối lượng của các phần tử
Page 5/40
DESCRIPTION OF STRUCTURAL CALCULATION
Page 6/40
DESCRIPTION OF STRUCTURAL CALCULATION
Page 7/40
DESCRIPTION OF STRUCTURAL CALCULATION
5. Annalysis of embeded level 12 to level 25/ Tính toán kiểm tra cast-in tầng 12 đến tầng 25
PANEL DIMENSION DEAD FSW WIND LOAD WIND FWL FINS FFL SEISMIS FSL
LOCATION DISCRIPTION LOADCASE ADJACENT CALCULATION RESULT
mm mm KICKER (N) KPA (N) (N) (N)
PANEL
LOADCASE 1 1234 3800 0 3800 3841 1.77 8300 1681.5
LOCATION 1 TOP FLOOR SEE CALCULATION
LOADCASE 2 1234 3800 0 3800 3841 2.66 12473 1681.5
level 12 to level 18 TYPICAL RESULT IN ANNEX 3
LOADCASE 3 1234 3800 0 3800 3841 2.66 12473 1681.5 922
LOADCASE 1 1234 3800 0 3800 3841 1.85 8675 1757.5
LOCATION 1 TOP FLOOR SEE CALCULATION
LOADCASE 2 1234 3800 0 3800 3841 2.78 13036 1757.5
level 19 to level 25 TYPICAL RESULT IN ANNEX 4
LOADCASE 3 1234 3800 0 3800 3841 2.78 13036 1757.5 922
LOADCASE 1 1190 3800 0 3800 3841 1.77 8004 1681.5
LOCATION 2 BEAM SIDE SEE CALCULATION
LOADCASE 2 1190 3800 0 3800 3841 2.66 12029 1681.5
level 12 to level 25 TYPICAL RESULT IN ANNEX 5
LOADCASE 3 1190 3800 0 3800 3841 2.66 12029 1681.5 922
1190 3800 0 3800 1920 1.77 4002
LOADCASE 1
1234 3800 0 3800 1920 1.77 4150
LOCATION 3 BEAM SIDE 1190 3800 0 3800 1920 2.66 6014 SEE CALCULATION
LOADCASE 2
level 12 to level 25 CORNER 1234 3800 0 3800 1920 2.66 6237 RESULT IN ANNEX 6
1190 3800 0 3800 1920 2.66 6014 461
LOADCASE 3
1234 3800 0 3800 1920 2.66 6237 461
1213 3800 0 3800 1920 1.77 4079
LOADCASE 1
1260 3800 0 3800 1920 1.77 4237
LOCATION 4 TOP FLOOR 1213 3800 0 3800 1920 2.66 6131 SEE CALCULATION
LOADCASE 2
level 12 to level 25 CORNER 1260 3800 0 3800 1920 2.66 6368 RESULT IN ANNEX 7
1213 3800 0 3800 1920 2.66 6131 461
LOADCASE 3
1260 3800 0 3800 1920 2.66 6368 461
Page 8/40
DESCRIPTION OF STRUCTURAL CALCULATION
Page 9/40
DESCRIPTION OF STRUCTURAL CALCULATION
Page 10/40
DESCRIPTION OF STRUCTURAL CALCULATION
Page 11/40
DESCRIPTION OF STRUCTURAL CALCULATION
Page 12/40
DESCRIPTION OF STRUCTURAL CALCULATION
Parameter:
Wind load: WL (kpa) = 1.77
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
Depth of fins: D(mm) = 250
FSW (N) = 3841
FWLP (N) = WLxHxW = 8300
FFL (N) = WLxHxD = 1682
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 3.1)
Page 13/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 1 – Load case 2 LUMINARE
(level 12-18) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.66
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
Depth of fins: D(mm) = 250
FSW (N) = 3841
FWLS (N) = WLxHxW = 12473
FFL (N) = WLxHxD = 1682
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 3.2)
Page 14/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 1 – Load case 3 LUMINARE
(level 12-18) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.66
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
Depth of fins: D(mm) = 250
FSW (N) = 3841
FWLS (N) = WLxHxW = 12473
FFL (N) = WLxHxD = 1682
FSL (N) = 0.24FSW = 922
Load case:
1.2FSW+1.2(FWLS+FFL)+1.2x0.8FSL
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 3.3)
Page 15/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 1 – Load case 1 LUMINARE
(level 19-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 1.85
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
Depth of fins: D(mm) = 250
FSW (N) = 3841
FWLP (N) = WLxHxW = 8675
FFL (N) = WLxHxD = 1758
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 4.1)
Page 16/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 1 – Load case 2 LUMINARE
(level 19-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.78
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
Depth of fins: D(mm) = 250
FSW (N) = 3841
FWLS (N) = WLxHxW = 13036
FFL (N) = WLxHxD = 1758
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 4.2)
Page 17/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 1 – Load case 3 LUMINARE
(level 19-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.5
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
Depth of fins: D(mm) = 250
FSW (N) = 3841
FWLS (N) = WLxHxW = 13036
FFL (N) = WLxHxD = 1758
FSL (N) = 0.24FSW = 922
Load case:
1.2FSW+1.2(FWLS+FFL)+1.2x0.8FSL
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 4.3)
Page 18/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 2 – Load case 1 LUMINARE
(level 12-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 1.85
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
Depth of fins: D(mm) = 250
FSW (N) = 3841
FWLP (N) = WLxHxW = 8366
FFL (N) = WLxHxD = 1758
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 5.1)
Page 19/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 2 – Load case 2 LUMINARE
(level 12-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.78
Width of panel: W = 1234
Heigh of panel: H(mm) = 3800
Depth of fins: D(mm) = 250
FSW (N) = 3841
FWLS (N) = WLxHxW = 12571
FFL (N) = WLxHxD = 1758
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 5.2)
Page 20/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 2 – Load case 3 LUMINARE
(level 12-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.78
Width of panel: W = 1234
Heigh of panel: H(mm) = 3800
Depth of fins: D(mm) = 250
FSW (N) = 3841
FWLS (N) = WLxHxW = 12571
FFL (N) = WLxHxD = 1758
FSL (N) = 0.24Fsw = 922
Load case:
1.2FSW+1.2(FWLS+FFL)+1.2x0.8FSL
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 5.3)
Page 21/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 3 – Load case 1 LUMINARE
(level 12-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 1.85
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
FSW (N) = 1920
FWLP (N) = WLxHxW/2 = 4338
Loadcase: 1.4FSW+1.4FWLP
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 6.1)
Page 22/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 3 – Load case 2 LUMINARE
(level 12-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.78
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
FSW (N) = 1920
FWLS (N) = WLxHxW/2 = 6518
Loadcase: FSW+1.4FWLS
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 6.2)
Page 23/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 3 – Load case 3 LUMINARE
(level 12-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.78
Width of panel: W(mm) = 1234
Heigh of panel: H(mm) = 3800
FSW (N) = 1920
FWLS (N) = WLxHxW/2= 6518
FSL (N) = 0.24Fsw = 461
Loadcase:
1.2FSW+1.2FWLS+1.2x0.8FSL
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 6.3)
Page 24/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 4 – Load case 1 LUMINARE
(level 12-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 1.85
Width of panel: W(mm) = 1260
Heigh of panel: H(mm) = 3800
FSW (N) = 1920
FWLP (N) = WLxHxW/2 = 4429
Loadcase:
1.4FSW+1.4FWLP
Moment eccentricity:
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 7.1)
Page 25/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 4 – Load case 2 LUMINARE
(level 12-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.78
Width of panel: W(mm) = 1260
Heigh of panel: H(mm) = 3800
FSW (N) = 1920
FWLS (N) = WLxHxW/2 = 6655
Loadcase: FSW+1.4FWLS
Moment eccentricity:
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 7.2)
Page 26/40
DESCRIPTION OF STRUCTURAL CALCULATION
Project Name:
STRUCTURAL ENGINEERING CALCULATION
LANCASTER
Subject: Cast in channel at location 4 – Load case 3 LUMINARE
(level 12-25) Typical Unitized Curtain Wall
Parameter:
Wind load: WL (kpa) = 2.78
Width of panel: W(mm) = 1260
Heigh of panel: H(mm) = 3800
FSW (N) = 1920
FWLS (N) = WLxHxW/2 = 6655
FSL (N) = 0.24Fsw = 461
Loadcase:
1.2FSW+1.2FWLS+1.2x0.8FSL
Moment eccentricity:
Result:
Calculation cast-in channel by Hilti
Profis software:
(Refer to Calculation appendix 7.3)
Page 27/40
DESCRIPTION OF STRUCTURAL CALCULATION
5.3. Load capacity Analysis of Channel./ TÍnh toán khả năng chịu lực của cast-in
Page 28/40
DESCRIPTION OF STRUCTURAL CALCULATION
The static component of wind load/ Tải trọng tính toán gió tĩnh
Wt = n.Wo.k.c
+ Wo: Value of wind pressure subject /
Design wind velocity V3s = 45m/s as per specification.
Wo = 0.0613 x V3s2 = 0.0613x 452 = 124 daN/m2
+ c: Aerodynamic coefficient/ Hệ số khí động học
The dynamic component of wind load/ Tải trọng tính toán động:
Wd = Wt . .
+ ζ : Dynamical factor/ Hệ số áp lực
Page 29/40
DESCRIPTION OF STRUCTURAL CALCULATION
W = Wt + Wd
Page 30/40
DESCRIPTION OF STRUCTURAL CALCULATION
Wind load table at each floor level/ Áp lực gió tác dụng tại mỗi tầng
Design windload
Level Height Static (daN/m ) 2
Dynamic (daN/m2) Total=Static+Dynamic (daN/m 2)
Floor k
(m) (m) Negative Negative Negative Negative Negative Negative
Positive Positive Positive
Non-corner Corner Non-corner Corner Non-corner Corner
1 1.00 6.10
2 7.10 3.80 0.930 92.35 -69.26 -138.53 33.51 -25.13 -50.27 125.86 -94.40 -188.79
3 10.90 3.80 1.014 100.70 -75.53 -151.05 34.95 -26.21 -52.43 135.65 -101.74 -203.48
4 14.70 3.80 1.075 106.75 -80.06 -160.13 35.85 -26.89 -53.78 142.60 -106.95 -213.90
5 18.50 3.80 1.115 110.73 -83.05 -166.10 35.91 -26.93 -53.87 146.64 -109.98 -219.96
6 22.30 3.80 1.151 114.30 -85.73 -171.45 36.15 -27.11 -54.23 150.45 -112.84 -225.68
7 26.10 3.80 1.185 117.68 -88.26 -176.52 36.47 -27.35 -54.71 154.15 -115.61 -231.23
8 29.90 3.80 1.219 121.05 -90.79 -181.58 36.74 -27.56 -55.11 157.79 -118.34 -236.69
9 33.70 3.80 1.242 123.34 -92.51 -185.01 36.67 -27.50 -55.01 160.01 -120.01 -240.02
10 37.50 3.80 1.265 125.62 -94.22 -188.43 36.62 -27.47 -54.93 162.24 -121.68 -243.36
11 41.30 3.80 1.288 127.91 -95.93 -191.87 36.63 -27.47 -54.95 164.54 -123.41 -246.81
12 45.10 3.80 1.311 130.19 -97.64 -195.29 36.81 -27.61 -55.22 167.00 -125.25 -250.50
13 48.90 5.35 1.333 132.37 -99.28 -198.56 36.95 -27.71 -55.43 169.32 -126.99 -253.98
14 54.25 3.80 1.357 134.76 -101.07 -202.14 36.98 -27.74 -55.47 171.74 -128.81 -257.61
15 58.05 3.80 1.372 136.25 -102.19 -204.38 36.91 -27.68 -55.37 173.16 -129.87 -259.74
16 61.85 3.80 1.386 137.64 -103.23 -206.46 36.83 -27.62 -55.25 174.47 -130.85 -261.71
17 65.65 3.80 1.400 139.03 -104.27 -208.55 36.79 -27.59 -55.19 175.82 -131.87 -263.73
18 69.45 3.80 1.413 140.32 -105.24 -210.48 36.77 -27.58 -55.16 177.09 -132.82 -265.64
19 73.25 3.80 1.426 141.61 -106.21 -212.42 36.69 -27.52 -55.04 178.30 -133.73 -267.45
20 77.05 3.80 1.440 143.00 -107.25 -214.50 36.63 -27.47 -54.95 179.63 -134.72 -269.45
21 80.85 3.80 1.453 144.29 -108.22 -216.44 36.54 -27.41 -54.81 180.83 -135.62 -271.25
22 84.65 3.80 1.464 145.38 -109.04 -218.07 36.57 -27.43 -54.86 181.95 -136.46 -272.93
23 88.45 3.80 1.475 146.48 -109.86 -219.72 36.53 -27.40 -54.80 183.01 -137.26 -274.52
24 92.25 3.80 1.487 147.67 -110.75 -221.51 36.51 -27.38 -54.77 184.18 -138.14 -276.27
25 96.05 3.80 1.498 148.76 -111.57 -223.14 36.46 -27.35 -54.69 185.22 -138.92 -277.83
26 99.85 6.000 1.510 149.95 -112.46 -224.93 36.43 -27.32 -54.65 186.38 -139.79 -279.57
27 105.85 3.350 1.524 151.34 -113.51 -227.01 36.37 -27.28 -54.56 187.71 -140.78 -281.57
28 109.20 2.650 1.532 152.14 -114.11 -228.21 36.30 -27.23 -54.45 188.44 -141.33 -282.66
TERRACE 111.85 2.550 1.538 152.73 -114.55 -229.10 36.25 -27.19 -54.38 188.98 -141.74 -283.47
ROOF 114.40 1.545 153.43 -115.07 -230.15 36.23 -27.17 -54.35 189.66 -142.25 -284.49
Page 31/40
DESCRIPTION OF STRUCTURAL CALCULATION
2. Annex 2: Calculate seismic load/ Phụ lục 2: Tính toán tải động đất.
⇒The seismic presssure applied to the module is equal to 0.24 of the element weight
Page 32/40
DESCRIPTION OF STRUCTURAL CALCULATION
Computation dead load of panel/ Tính toán tải trọng bản thân panel
No. Material Thk.(mm) Width(mm) Height(mm) Weight(kg)
1 Glass 33.52(8+6x2+12+1.52) 1250 3800 237.50
2 Mullion 1 13.7 3800 52.06
3 Transom 2 12.1 1250 30.25
4 Rook Wool 50 1250 1050 3.28
5 1.5mm Thk steel sheet 1250 1050 15.45
Back Pan
6 3mm Thk Alu sheet 1250 1050 10.63
7 Accessory 10% 34.92
Weight of 1 Panel 1234mmx3800mm 384.09
PRELIMINARY COMPUTATION DEAD LOAD OF PANEL
Page 33/40
DESCRIPTION OF STRUCTURAL CALCULATION
Page 34/40
DESCRIPTION OF STRUCTURAL CALCULATION
Page 35/40
DESCRIPTION OF STRUCTURAL CALCULATION
3. Annex 3: Load capacity analysis of cast-in channel at location 1 level 12 to level 18/ Phụ lục 3: Phân tích khả
năng chịu lực của cast-in channel vị trí 1 tầng 12 đến tầng 18
Page 36/40
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Specifier's comments: LV 12-18, Load case: 1.4FSW+1.4(FWLP+FFL)
Annex 3.1
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4, longitudinal shear as per Hilti method
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: 0 mm
2 Overall Result
Design ok! (Maximum utilization: 62%)
IMPORTANT! Failure analysis modes evaluated by PROFIS follow EOTA TR 047/EN 1992-4. This DOES NOT include
evaluating the base material (e.g. edge-of-slab) capacity to resist compressive forces generated by the fixture. The engineer
must ALWAYS verify the base material (e.g. edge-of-slab) design is capable of resisting the applied loading.
Compressive forces generated by the fixture = 16.666 kN
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.230 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] Vy [kN]
a1 5.576 4.718
a2 5.713 6.902
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Anchor longitudinal shear forces [kN]
Anchor Vx
a1 1.177
a2 1.177
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 5.713 18.389 32 ok
Connection anchor-channel 5.713 13.889 42 ok
Channel lip 5.816 13.889 42 ok
Channel bolt 5.816 83.733 7 ok
Flexure channel 0.230 0.852 28 ok
Pull-out 5.713 31.350 19 ok
Concrete cone 5.713 16.442 35 ok
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.2, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.2, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
5.816 125.600 1.500 83.733
Mch
Ed [kNm] MRk,s,flex [kNm] gMs,flex MRd,s,flex [kNm]
0.230 0.980 1.150 0.852
5.1.2 Pull-out failure (Anchor a2, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
209
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
5.713 7.5 30.0 47.025 1.500 31.350
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.1.3 Concrete cone (Anchor a2, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 8.632 50.240 18 ok
Flexure channel lip w/o lever arm - 8.552 13.889 62 ok
perpendicular
Flexure channel lip w/o lever arm - 1.177 7.817 16 ok
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 6.902 13.889 50 ok
Anchor - longitudinal 1.177 12.267 10 ok
Connection anchor/channel - 6.902 13.889 50 ok
perpendicular
Connection anchor/channel - 1.177 6.944 17 ok
longitudinal
Concrete pryout, perpendicular 6.902 34.687 20 ok
Concrete pryout, longitudinal 1.177 32.744 4 ok
Concrete edge - perpendicular N/A N/A N/A N/A
Concrete edge - longitudinal 2.354 50.562 5 ok
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
8.632 8.552 1.177 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.2, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Local flexure of channel lip - shear longitudinal w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (Hilti method
based on CEN/TR 17080 section 7.3.3.1)
VRk,s,l,x
Vcb
Ed,x ≤ VRd,s,l,x =
gMs,l,x
VRk,s,l,x = V0Rk,s,l,x · y l,V
y l,V = 1.0
gMs,l,x = ginst · gMs,l
Vcb
Ed,x [kN] V0Rk,s,l,x [kN] VRk,s,l,x [kN] gMs,l ginst gMs,l,x VRd,s,l,x [kN]
1.177 19.700 19.700 1.800 1.400 2.520 7.817
5.2.1.4 Anchor - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.5 Anchor - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080 section 7.2.2.2.2)
VRk,s,a,x
VaEd,x ≤ VRd,s,a,x =
gMs
5.2.1.6 Connection between anchor and channel - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.7 Connection between anchor and channel - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR
17080 section 7.2.2.2.3)
VRk,s,c,x
VaEd,x ≤ VRd,s,c,x =
gMs,ca
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.3 Concrete pry-out failure - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080
section 7.2.2.3)
VRk,cp,x
VaEd,x ≤ VRd,cp,x =
gMc
VRk,cp,x = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.4 Concrete edge failure - shear longitudinal, direction y- (Anchor a1, Channel a) (Hilti method based on EN 1992-4
section 7.2.2.5, CEN/TR 17080 section 7.2.2.4)
VRk,c,x
VaEd,x ≤ VRd,c,x =
gMc
Ac,V
VRk,c,x = V0Rk,c · · y s,V · y h,V · y re,V
A0c,V
0.5
a = 0.1 (cl )f
1
0.2
b = 0.1 (dc )nom
1
c2
y s,V = 0.7 + 0.3 ≤ 1.0
1.5 · c1
0.5
y h,V = (1.5h· c ) 1
≥ 1.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.2)
2 2
2
=( ) = 0.00482
cb
N Ed
bN,s
N Rd,s,cb
2
=( ) = 0.02952
√V cb 2
+V
Ed,y
cb 2
Ed,x
bV,s
V Rd,s,cb
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.2)
k71 k71 2
2.0
= max ( ) = 0.17535
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
2.0
=( ) = 0.37912
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.02267
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.3 Anchor and connection between anchor and channel (Anchor a2)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
2.0
= max( )
a
N Ed NaEd
bN,ac , = 0.16919
N Rd,s,a NRd,s,c
2.0
= max( ) = 0.24694
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.02873
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.16919 + 0.24694 + 0.02873 ≤ 1.0
(Utilization : 45%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3.4 Concrete anchor (Anchor a2)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.20481
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.08876
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.01005
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 16
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 250 mm x 243 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 250 x 10 x 0 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
125 125
40
1.1 1.2
122
x
203
117
122
40 170 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 17
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
Specifier's comments: LV 12-18, Load case: 1.4FSW+1.4(FWLS+FFL)
Annex 3.2
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4, longitudinal shear as per Hilti method
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: -25 mm
2 Overall Result
Design ok! (Maximum utilization: 90%)
IMPORTANT! Failure analysis modes evaluated by PROFIS follow EOTA TR 047/EN 1992-4. This DOES NOT include
evaluating the base material (e.g. edge-of-slab) capacity to resist compressive forces generated by the fixture. The engineer
must ALWAYS verify the base material (e.g. edge-of-slab) design is capable of resisting the applied loading.
Compressive forces generated by the fixture = 5.377 kN
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.000 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] Vy [kN]
a1 0.000 -10.846
a2 0.000 -6.617
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
Anchor longitudinal shear forces [kN]
Anchor Vx
a1 1.177
a2 1.177
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor N/A N/A N/A N/A
Connection anchor-channel N/A N/A N/A N/A
Channel lip N/A N/A N/A N/A
Channel bolt N/A N/A N/A N/A
Flexure channel N/A N/A N/A N/A
Pull-out N/A N/A N/A N/A
Concrete cone N/A N/A N/A N/A
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 11.533 50.240 23 ok
Flexure channel lip w/o lever arm - 11.473 19.389 60 ok
perpendicular
Flexure channel lip w/o lever arm - 1.177 7.817 16 ok
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 10.846 26.400 42 ok
Anchor - longitudinal 1.177 12.267 10 ok
Connection anchor/channel - 10.846 22.000 50 ok
perpendicular
Connection anchor/channel - 1.177 6.944 17 ok
longitudinal
Concrete pryout, perpendicular 10.846 35.172 31 ok
Concrete pryout, longitudinal 1.177 32.744 4 ok
Concrete edge - perpendicular 10.846 12.113 90 ok
Concrete edge - longitudinal 2.354 50.562 5 ok
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
11.533 11.473 1.177 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Local flexure of channel lip - shear longitudinal w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (Hilti method
based on CEN/TR 17080 section 7.3.3.1)
VRk,s,l,x
Vcb
Ed,x ≤ VRd,s,l,x =
gMs,l,x
VRk,s,l,x = V0Rk,s,l,x · y l,V
y l,V = 1.0
gMs,l,x = ginst · gMs,l
Vcb
Ed,x [kN] V0Rk,s,l,x [kN] VRk,s,l,x [kN] gMs,l ginst gMs,l,x VRd,s,l,x [kN]
1.177 19.700 19.700 1.800 1.400 2.520 7.817
5.2.1.4 Anchor - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.5 Anchor - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080 section 7.2.2.2.2)
VRk,s,a,x
VaEd,x ≤ VRd,s,a,x =
gMs
5.2.1.6 Connection between anchor and channel - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.1.7 Connection between anchor and channel - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR
17080 section 7.2.2.2.3)
VRk,s,c,x
VaEd,x ≤ VRd,s,c,x =
gMs,ca
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.3 Concrete pry-out failure - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080
section 7.2.2.3)
VRk,cp,x
VaEd,x ≤ VRd,cp,x =
gMc
VRk,cp,x = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.4 Concrete edge failure - shear perpendicular, direction y- (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.5 Concrete edge failure - shear longitudinal, direction y- (Anchor a1, Channel a) (Hilti method based on EN 1992-4
section 7.2.2.5, CEN/TR 17080 section 7.2.2.4)
VRk,c,x
VaEd,x ≤ VRd,c,x =
gMc
Ac,V
VRk,c,x = V0Rk,c · · y s,V · y h,V · y re,V
A0c,V
0.5
a = 0.1 (cl )f
1
0.2
b = 0.1 (dc )nom
1
c2
y s,V = 0.7 + 0.3 ≤ 1.0
1.5 · c1
0.5
y h,V = (1.5h· c ) 1
≥ 1.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Point of load application - channel lip (Fixture 1, Channel bolt 1.1)
k71 k71 2
bN+V,la,c = max ( Ncb
Ed
; ) ( ) (
Mch
Ed
NRd,s,l MRd,s,flex
+
Vcb
Ed,y
VRd,s,l,y
+
Vcb
Ed,x
VRd,s,l,x ) ≤ 1.0
1.0
= max ( ) = 0.00000
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
1.0
=( ) = 0.59174
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.02267
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.2 Anchor and connection between anchor and channel (Anchor a1)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
1.0
= max( )
a
N Ed NaEd
bN,ac , = 0.00000
N Rd,s,a NRd,s,c
1.0
= max( ) = 0.49300
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.02873
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.00000 + 0.49300 + 0.02873 ≤ 1.0
(Utilization : 53%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.3.3 Concrete anchor (Anchor a1)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.00000
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.84727
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.01005
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 250 mm x 243 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 250 x 10 x 0 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
125 125
40
1.1 1.2
122
x
203
117
122
40 170 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 16
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Specifier's comments: LV 12 18, Load case: 1.2FSW+1.2(FWLS+FFL)+1.2x0.8FSL
Annex 3.3
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4, longitudinal shear as per Hilti method
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: -25 mm
2 Overall Result
Design ok! (Maximum utilization: 82%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.000 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] Vy [kN]
a1 0.000 -9.791
a2 0.000 -6.062
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Anchor longitudinal shear forces [kN]
Anchor Vx
a1 1.009
a2 1.009
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor N/A N/A N/A N/A
Connection anchor-channel N/A N/A N/A N/A
Channel lip N/A N/A N/A N/A
Channel bolt N/A N/A N/A N/A
Flexure channel N/A N/A N/A N/A
Pull-out N/A N/A N/A N/A
Concrete cone N/A N/A N/A N/A
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 10.326 50.240 21 ok
Flexure channel lip w/o lever arm - 10.277 19.389 54 ok
perpendicular
Flexure channel lip w/o lever arm - 1.009 7.817 13 ok
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 9.791 26.400 38 ok
Anchor - longitudinal 1.009 12.267 9 ok
Connection anchor/channel - 9.791 22.000 45 ok
perpendicular
Connection anchor/channel - 1.009 6.944 15 ok
longitudinal
Concrete pryout, perpendicular 9.791 35.111 28 ok
Concrete pryout, longitudinal 1.009 32.744 4 ok
Concrete edge - perpendicular 9.791 12.077 82 ok
Concrete edge - longitudinal 2.018 50.562 4 ok
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
10.326 10.277 1.009 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Local flexure of channel lip - shear longitudinal w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (Hilti method
based on CEN/TR 17080 section 7.3.3.1)
VRk,s,l,x
Vcb
Ed,x ≤ VRd,s,l,x =
gMs,l,x
VRk,s,l,x = V0Rk,s,l,x · y l,V
y l,V = 1.0
gMs,l,x = ginst · gMs,l
Vcb
Ed,x [kN] V0Rk,s,l,x [kN] VRk,s,l,x [kN] gMs,l ginst gMs,l,x VRd,s,l,x [kN]
1.009 19.700 19.700 1.800 1.400 2.520 7.817
5.2.1.4 Anchor - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.5 Anchor - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080 section 7.2.2.2.2)
VRk,s,a,x
VaEd,x ≤ VRd,s,a,x =
gMs
5.2.1.6 Connection between anchor and channel - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.7 Connection between anchor and channel - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR
17080 section 7.2.2.2.3)
VRk,s,c,x
VaEd,x ≤ VRd,s,c,x =
gMs,ca
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.3 Concrete pry-out failure - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080
section 7.2.2.3)
VRk,cp,x
VaEd,x ≤ VRd,cp,x =
gMc
VRk,cp,x = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.4 Concrete edge failure - shear perpendicular, direction y- (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.5 Concrete edge failure - shear longitudinal, direction y- (Anchor a1, Channel a) (Hilti method based on EN 1992-4
section 7.2.2.5, CEN/TR 17080 section 7.2.2.4)
VRk,c,x
VaEd,x ≤ VRd,c,x =
gMc
Ac,V
VRk,c,x = V0Rk,c · · y s,V · y h,V · y re,V
A0c,V
0.5
a = 0.1 (cl )f
1
0.2
b = 0.1 (dc )nom
1
c2
y s,V = 0.7 + 0.3 ≤ 1.0
1.5 · c1
0.5
y h,V = (1.5h· c ) 1
≥ 1.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Point of load application - channel lip (Fixture 1, Channel bolt 1.1)
k71 k71 2
bN+V,la,c = max ( Ncb
Ed
; ) ( ) (
Mch
Ed
NRd,s,l MRd,s,flex
+
Vcb
Ed,y
VRd,s,l,y
+
Vcb
Ed,x
VRd,s,l,x ) ≤ 1.0
1.0
= max ( ) = 0.00000
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
1.0
=( ) = 0.53004
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.01666
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.2 Anchor and connection between anchor and channel (Anchor a1)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
1.0
= max( )
a
N Ed NaEd
bN,ac , = 0.00000
N Rd,s,a NRd,s,c
1.0
= max( ) = 0.44504
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.02111
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.00000 + 0.44504 + 0.02111 ≤ 1.0
(Utilization : 47%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3.3 Concrete anchor (Anchor a1)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.00000
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.72996
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00797
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 250 mm x 243 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 250 x 10 x 0 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
125 125
40
1.1 1.2
122
x
203
117
122
40 170 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 16
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
DESCRIPTION OF STRUCTURAL CALCULATION
4. Annex 4: Load capacity analysis of cast-in channel at location 1 level 19 to level 25/ Phụ lục 4: Phân tích khả
năng chịu lực của cast-in channel vị trí 1 tầng 19 đến tầng 25
Page 37/40
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.4FSW+1.4(FWLP+FFL)
Annex 4.1
1 Input data
Channel type HAC-50 106/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 106 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 42 mm, height: hch = 31 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4, longitudinal shear as per Hilti method
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: 0 mm
2 Overall Result
Design ok! (Maximum utilization: 46%)
IMPORTANT! Failure analysis modes evaluated by PROFIS follow EOTA TR 047/EN 1992-4. This DOES NOT include
evaluating the base material (e.g. edge-of-slab) capacity to resist compressive forces generated by the fixture. The engineer
must ALWAYS verify the base material (e.g. edge-of-slab) design is capable of resisting the applied loading.
Compressive forces generated by the fixture = 16.957 kN
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 346 [mm] ≥ s
Iy = 33125 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.236 [kNm]
hef = 106
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] Vy [kN]
a1 5.721 4.969
a2 5.859 7.176
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Anchor longitudinal shear forces [kN]
Anchor Vx
a1 1.231
a2 1.231
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 5.859 29.167 21 ok
Connection anchor-channel 5.859 19.444 31 ok
Channel lip 5.970 19.444 31 ok
Channel bolt 5.970 83.733 8 ok
Flexure channel 0.236 1.170 21 ok
Pull-out 5.859 38.700 16 ok
Concrete cone 5.859 19.252 31 ok
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.2, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.2, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
5.970 125.600 1.500 83.733
Mch
Ed [kNm] MRk,s,flex [kNm] gMs,flex MRd,s,flex [kNm]
0.236 1.345 1.150 1.170
5.1.2 Pull-out failure (Anchor a2, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
258
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
5.859 7.5 30.0 58.050 1.500 38.700
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.1.3 Concrete cone (Anchor a2, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 9.023 50.240 18 ok
Flexure channel lip w/o lever arm - 8.939 19.444 46 ok
perpendicular
Flexure channel lip w/o lever arm - 1.231 7.817 16 ok
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 7.176 19.444 37 ok
Anchor - longitudinal 1.231 19.333 7 ok
Connection anchor/channel - 7.176 19.444 37 ok
perpendicular
Connection anchor/channel - 1.231 9.722 13 ok
longitudinal
Concrete pryout, perpendicular 7.176 41.011 18 ok
Concrete pryout, longitudinal 1.231 38.310 4 ok
Concrete edge - perpendicular N/A N/A N/A N/A
Concrete edge - longitudinal 2.461 53.886 5 ok
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
9.023 8.939 1.231 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.2, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Local flexure of channel lip - shear longitudinal w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (Hilti method
based on CEN/TR 17080 section 7.3.3.1)
VRk,s,l,x
Vcb
Ed,x ≤ VRd,s,l,x =
gMs,l,x
VRk,s,l,x = V0Rk,s,l,x · y l,V
y l,V = 1.0
gMs,l,x = ginst · gMs,l
Vcb
Ed,x [kN] V0Rk,s,l,x [kN] VRk,s,l,x [kN] gMs,l ginst gMs,l,x VRd,s,l,x [kN]
1.231 19.700 19.700 1.800 1.400 2.520 7.817
5.2.1.4 Anchor - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.5 Anchor - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080 section 7.2.2.2.2)
VRk,s,a,x
VaEd,x ≤ VRd,s,a,x =
gMs
5.2.1.6 Connection between anchor and channel - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.7 Connection between anchor and channel - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR
17080 section 7.2.2.2.3)
VRk,s,c,x
VaEd,x ≤ VRd,s,c,x =
gMs,ca
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.3 Concrete pry-out failure - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080
section 7.2.2.3)
VRk,cp,x
VaEd,x ≤ VRd,cp,x =
gMc
VRk,cp,x = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.4 Concrete edge failure - shear longitudinal, direction y- (Anchor a1, Channel a) (Hilti method based on EN 1992-4
section 7.2.2.5, CEN/TR 17080 section 7.2.2.4)
VRk,c,x
VaEd,x ≤ VRd,c,x =
gMc
Ac,V
VRk,c,x = V0Rk,c · · y s,V · y h,V · y re,V
A0c,V
0.5
a = 0.1 (cl )f
1
0.2
b = 0.1 (dc )nom
1
c2
y s,V = 0.7 + 0.3 ≤ 1.0
1.5 · c1
0.5
y h,V = (1.5h· c ) 1
≥ 1.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.2)
2 2
2
=( ) = 0.00508
cb
N Ed
bN,s
N Rd,s,cb
2
=( ) = 0.03226
√V cb 2
+V
Ed,y
cb 2
Ed,x
bV,s
V Rd,s,cb
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.2)
k71 k71 2
2.0
= max ( ) = 0.09426
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
2.0
=( ) = 0.21133
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.02478
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.3 Anchor and connection between anchor and channel (Anchor a2)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
2.0
= max( )
a
N Ed NaEd
bN,ac , = 0.09080
N Rd,s,a NRd,s,c
2.0
= max( ) = 0.13618
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.01602
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.09080 + 0.13618 + 0.01602 ≤ 1.0
(Utilization : 25%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3.4 Concrete anchor (Anchor a2)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.16789
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.07319
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00976
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 16
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 250 mm x 243 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 250 x 10 x 0 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
125 125
40
1.1 1.2
122
x
203
117
122
40 170 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 17
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.4FSW+1.4(FWLS+FFL)
Annex 4.2
1 Input data
Channel type HAC-50 106/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 106 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 42 mm, height: hch = 31 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4, longitudinal shear as per Hilti method
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: -25 mm
2 Overall Result
Design ok! (Maximum utilization: 95%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 346 [mm] ≥ s
Iy = 33125 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.000 [kNm]
hef = 106
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] Vy [kN]
a1 0.000 -11.261
a2 0.000 -6.989
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
Anchor longitudinal shear forces [kN]
Anchor Vx
a1 1.231
a2 1.231
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor N/A N/A N/A N/A
Connection anchor-channel N/A N/A N/A N/A
Channel lip N/A N/A N/A N/A
Channel bolt N/A N/A N/A N/A
Flexure channel N/A N/A N/A N/A
Pull-out N/A N/A N/A N/A
Concrete cone N/A N/A N/A N/A
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 12.054 50.240 24 ok
Flexure channel lip w/o lever arm - 11.991 26.389 46 ok
perpendicular
Flexure channel lip w/o lever arm - 1.231 7.817 16 ok
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 11.261 35.733 32 ok
Anchor - longitudinal 1.231 19.333 7 ok
Connection anchor/channel - 11.261 29.778 38 ok
perpendicular
Connection anchor/channel - 1.231 9.722 13 ok
longitudinal
Concrete pryout, perpendicular 11.261 41.698 28 ok
Concrete pryout, longitudinal 1.231 38.310 4 ok
Concrete edge - perpendicular 11.261 11.940 95 ok
Concrete edge - longitudinal 2.461 53.886 5 ok
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
12.054 11.991 1.231 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Local flexure of channel lip - shear longitudinal w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (Hilti method
based on CEN/TR 17080 section 7.3.3.1)
VRk,s,l,x
Vcb
Ed,x ≤ VRd,s,l,x =
gMs,l,x
VRk,s,l,x = V0Rk,s,l,x · y l,V
y l,V = 1.0
gMs,l,x = ginst · gMs,l
Vcb
Ed,x [kN] V0Rk,s,l,x [kN] VRk,s,l,x [kN] gMs,l ginst gMs,l,x VRd,s,l,x [kN]
1.231 19.700 19.700 1.800 1.400 2.520 7.817
5.2.1.4 Anchor - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.5 Anchor - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080 section 7.2.2.2.2)
VRk,s,a,x
VaEd,x ≤ VRd,s,a,x =
gMs
5.2.1.6 Connection between anchor and channel - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.1.7 Connection between anchor and channel - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR
17080 section 7.2.2.2.3)
VRk,s,c,x
VaEd,x ≤ VRd,s,c,x =
gMs,ca
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.3 Concrete pry-out failure - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080
section 7.2.2.3)
VRk,cp,x
VaEd,x ≤ VRd,cp,x =
gMc
VRk,cp,x = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.4 Concrete edge failure - shear perpendicular, direction y- (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.5 Concrete edge failure - shear longitudinal, direction y- (Anchor a1, Channel a) (Hilti method based on EN 1992-4
section 7.2.2.5, CEN/TR 17080 section 7.2.2.4)
VRk,c,x
VaEd,x ≤ VRd,c,x =
gMc
Ac,V
VRk,c,x = V0Rk,c · · y s,V · y h,V · y re,V
A0c,V
0.5
a = 0.1 (cl )f
1
0.2
b = 0.1 (dc )nom
1
c2
y s,V = 0.7 + 0.3 ≤ 1.0
1.5 · c1
0.5
y h,V = (1.5h· c ) 1
≥ 1.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Point of load application - channel lip (Fixture 1, Channel bolt 1.1)
k71 k71 2
bN+V,la,c = max ( Ncb
Ed
; ) ( ) (
Mch
Ed
NRd,s,l MRd,s,flex
+
Vcb
Ed,y
VRd,s,l,y
+
Vcb
Ed,x
VRd,s,l,x ) ≤ 1.0
1.0
= max ( ) = 0.00000
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
1.0
=( ) = 0.45441
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.02478
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.2 Anchor and connection between anchor and channel (Anchor a1)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
1.0
= max( )
a
N Ed NaEd
bN,ac , = 0.00000
N Rd,s,a NRd,s,c
1.0
= max( ) = 0.37816
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.01602
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.00000 + 0.37816 + 0.01602 ≤ 1.0
(Utilization : 40%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.3.3 Concrete anchor (Anchor a1)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.00000
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.91591
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00976
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 250 mm x 243 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 250 x 10 x 0 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
125 125
40
1.1 1.2
122
x
203
117
122
40 170 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 16
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.2FSW+1.2(FWLS+FFL)+1.2x0.8FSL
Annex 4.3
1 Input data
Channel type HAC-50 106/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 106 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 42 mm, height: hch = 31 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4, longitudinal shear as per Hilti method
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: -25 mm
2 Overall Result
Design ok! (Maximum utilization: 86%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 346 [mm] ≥ s
Iy = 33125 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.000 [kNm]
hef = 106
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] Vy [kN]
a1 0.000 -10.145
a2 0.000 -6.383
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Anchor longitudinal shear forces [kN]
Anchor Vx
a1 1.055
a2 1.055
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor N/A N/A N/A N/A
Connection anchor-channel N/A N/A N/A N/A
Channel lip N/A N/A N/A N/A
Channel bolt N/A N/A N/A N/A
Flexure channel N/A N/A N/A N/A
Pull-out N/A N/A N/A N/A
Concrete cone N/A N/A N/A N/A
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 10.772 50.240 22 ok
Flexure channel lip w/o lever arm - 10.720 26.389 41 ok
perpendicular
Flexure channel lip w/o lever arm - 1.055 7.817 14 ok
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 10.145 35.733 29 ok
Anchor - longitudinal 1.055 19.333 6 ok
Connection anchor/channel - 10.145 29.778 35 ok
perpendicular
Connection anchor/channel - 1.055 9.722 11 ok
longitudinal
Concrete pryout, perpendicular 10.145 41.615 25 ok
Concrete pryout, longitudinal 1.055 38.310 3 ok
Concrete edge - perpendicular 10.145 11.906 86 ok
Concrete edge - longitudinal 2.109 53.886 4 ok
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
10.772 10.720 1.055 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Local flexure of channel lip - shear longitudinal w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (Hilti method
based on CEN/TR 17080 section 7.3.3.1)
VRk,s,l,x
Vcb
Ed,x ≤ VRd,s,l,x =
gMs,l,x
VRk,s,l,x = V0Rk,s,l,x · y l,V
y l,V = 1.0
gMs,l,x = ginst · gMs,l
Vcb
Ed,x [kN] V0Rk,s,l,x [kN] VRk,s,l,x [kN] gMs,l ginst gMs,l,x VRd,s,l,x [kN]
1.055 19.700 19.700 1.800 1.400 2.520 7.817
5.2.1.4 Anchor - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.5 Anchor - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080 section 7.2.2.2.2)
VRk,s,a,x
VaEd,x ≤ VRd,s,a,x =
gMs
5.2.1.6 Connection between anchor and channel - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.7 Connection between anchor and channel - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR
17080 section 7.2.2.2.3)
VRk,s,c,x
VaEd,x ≤ VRd,s,c,x =
gMs,ca
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.3 Concrete pry-out failure - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080
section 7.2.2.3)
VRk,cp,x
VaEd,x ≤ VRd,cp,x =
gMc
VRk,cp,x = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.4 Concrete edge failure - shear perpendicular, direction y- (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.5 Concrete edge failure - shear longitudinal, direction y- (Anchor a1, Channel a) (Hilti method based on EN 1992-4
section 7.2.2.5, CEN/TR 17080 section 7.2.2.4)
VRk,c,x
VaEd,x ≤ VRd,c,x =
gMc
Ac,V
VRk,c,x = V0Rk,c · · y s,V · y h,V · y re,V
A0c,V
0.5
a = 0.1 (cl )f
1
0.2
b = 0.1 (dc )nom
1
c2
y s,V = 0.7 + 0.3 ≤ 1.0
1.5 · c1
0.5
y h,V = (1.5h· c ) 1
≥ 1.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Point of load application - channel lip (Fixture 1, Channel bolt 1.1)
k71 k71 2
bN+V,la,c = max ( Ncb
Ed
; ) ( ) (
Mch
Ed
NRd,s,l MRd,s,flex
+
Vcb
Ed,y
VRd,s,l,y
+
Vcb
Ed,x
VRd,s,l,x ) ≤ 1.0
1.0
= max ( ) = 0.00000
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
1.0
=( ) = 0.40625
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.01820
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.2 Anchor and connection between anchor and channel (Anchor a1)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
1.0
= max( )
a
N Ed NaEd
bN,ac , = 0.00000
N Rd,s,a NRd,s,c
1.0
= max( ) = 0.34068
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.01176
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.00000 + 0.34068 + 0.01176 ≤ 1.0
(Utilization : 36%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3.3 Concrete anchor (Anchor a1)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.00000
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.78649
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00774
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 250 mm x 243 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 250 x 10 x 0 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
125 125
40
1.1 1.2
122
x
203
117
122
40 170 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 16
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 1
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
DESCRIPTION OF STRUCTURAL CALCULATION
5. Annex 5: Load capacity analysis of cast-in channel at location 2 level 12 to level 25/ Phụ lục 5: Phân tích khả
năng chịu lực của cast-in channel vị trí 2 tầng 12 đến tầng 25
Page 38/40
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.4FSW+1.4(FWLP+FFL)
Annex 5.1
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4, longitudinal shear as per Hilti method
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = ∞ mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: -25 mm
2 Overall Result
Design ok! (Maximum utilization: 22%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.000 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] Vy [kN]
a1 0.000 -3.003
a2 0.000 -2.374
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Anchor longitudinal shear forces [kN]
Anchor Vx
a1 1.231
a2 1.231
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor N/A N/A N/A N/A
Connection anchor-channel N/A N/A N/A N/A
Channel lip N/A N/A N/A N/A
Channel bolt N/A N/A N/A N/A
Flexure channel N/A N/A N/A N/A
Pull-out N/A N/A N/A N/A
Concrete cone N/A N/A N/A N/A
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 2.957 50.240 6 ok
Flexure channel lip w/o lever arm - 2.689 19.389 14 ok
perpendicular
Flexure channel lip w/o lever arm - 1.231 7.817 16 ok
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 3.003 26.400 12 ok
Anchor - longitudinal 1.231 12.267 11 ok
Connection anchor/channel - 3.003 22.000 14 ok
perpendicular
Connection anchor/channel - 1.231 6.944 18 ok
longitudinal
Concrete pryout, perpendicular 3.003 33.290 10 ok
Concrete pryout, longitudinal 1.231 24.617 5 ok
Concrete edge - perpendicular 3.003 14.004 22 ok
Concrete edge - longitudinal 2.461 48.560 6 ok
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
2.957 2.689 1.231 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Local flexure of channel lip - shear longitudinal w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (Hilti method
based on CEN/TR 17080 section 7.3.3.1)
VRk,s,l,x
Vcb
Ed,x ≤ VRd,s,l,x =
gMs,l,x
VRk,s,l,x = V0Rk,s,l,x · y l,V
y l,V = 1.0
gMs,l,x = ginst · gMs,l
Vcb
Ed,x [kN] V0Rk,s,l,x [kN] VRk,s,l,x [kN] gMs,l ginst gMs,l,x VRd,s,l,x [kN]
1.231 19.700 19.700 1.800 1.400 2.520 7.817
5.2.1.4 Anchor - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.5 Anchor - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080 section 7.2.2.2.2)
VRk,s,a,x
VaEd,x ≤ VRd,s,a,x =
gMs
5.2.1.6 Connection between anchor and channel - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.1.7 Connection between anchor and channel - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR
17080 section 7.2.2.2.3)
VRk,s,c,x
VaEd,x ≤ VRd,s,c,x =
gMs,ca
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.3 Concrete pry-out failure - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080
section 7.2.2.3)
VRk,cp,x
VaEd,x ≤ VRd,cp,x =
gMc
VRk,cp,x = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.4 Concrete edge failure - shear perpendicular, direction y- (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.5 Concrete edge failure - shear longitudinal, direction y+ (Anchor a1, Channel a) (Hilti method based on EN 1992-4
section 7.2.2.5, CEN/TR 17080 section 7.2.2.4)
VRk,c,x
VaEd,x ≤ VRd,c,x =
gMc
Ac,V
VRk,c,x = V0Rk,c · · y s,V · y h,V · y re,V
A0c,V
0.5
a = 0.1 (cl )f
1
0.2
b = 0.1 (dc )nom
1
c2
y s,V = 0.7 + 0.3 ≤ 1.0
1.5 · c1
0.5
y h,V = (1.5h· c ) 1
≥ 1.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Point of load application - channel lip (Fixture 1, Channel bolt 1.1)
k71 k71 2
bN+V,la,c = max ( Ncb
Ed
; ) ( ) (
Mch
Ed
NRd,s,l MRd,s,flex
+
Vcb
Ed,y
VRd,s,l,y
+
Vcb
Ed,x
VRd,s,l,x ) ≤ 1.0
1.0
= max ( ) = 0.00000
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
1.0
=( ) = 0.13866
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.02478
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.2 Anchor and connection between anchor and channel (Anchor a1)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
1.0
= max( )
a
N Ed NaEd
bN,ac , = 0.00000
N Rd,s,a NRd,s,c
1.0
= max( ) = 0.13652
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.03140
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.00000 + 0.13652 + 0.03140 ≤ 1.0
(Utilization : 17%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3.3 Concrete anchor (Anchor a1)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.00000
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.09932
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.01141
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 300 mm x 150 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 150 x 20 x 10 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
150 150
65
1.1 1.2 75
x
85
75
60 180 60
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 16
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.4FSW+1.4(FWLS+FFL)
Annex 5.2
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4, longitudinal shear as per Hilti method
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = ∞ mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: -25 mm
2 Overall Result
Design ok! (Maximum utilization: 98%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.545 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] Vy [kN]
a1 13.187 -3.003
a2 10.159 -2.374
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Anchor longitudinal shear forces [kN]
Anchor Vx
a1 1.231
a2 1.231
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 13.187 18.389 72 ok
Connection anchor-channel 13.187 13.889 95 ok
Channel lip 12.021 13.889 87 ok
Channel bolt 12.021 83.733 15 ok
Flexure channel 0.545 0.852 64 ok
Pull-out 13.187 31.350 43 ok
Concrete cone 13.187 16.706 79 ok
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
12.021 125.600 1.500 83.733
Mch
Ed [kNm] MRk,s,flex [kNm] gMs,flex MRd,s,flex [kNm]
0.545 0.980 1.150 0.852
5.1.2 Pull-out failure (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
209
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
13.187 7.5 30.0 47.025 1.500 31.350
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.3 Concrete cone (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 2.957 50.240 6 ok
Flexure channel lip w/o lever arm - 2.689 13.889 20 ok
perpendicular
Flexure channel lip w/o lever arm - 1.231 7.817 16 ok
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 3.003 13.889 22 ok
Anchor - longitudinal 1.231 12.267 11 ok
Connection anchor/channel - 3.003 13.889 22 ok
perpendicular
Connection anchor/channel - 1.231 6.944 18 ok
longitudinal
Concrete pryout, perpendicular 3.003 33.290 10 ok
Concrete pryout, longitudinal 1.231 24.617 5 ok
Concrete edge - perpendicular 3.003 14.004 22 ok
Concrete edge - longitudinal 2.461 48.560 6 ok
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
2.957 2.689 1.231 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Local flexure of channel lip - shear longitudinal w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (Hilti method
based on CEN/TR 17080 section 7.3.3.1)
VRk,s,l,x
Vcb
Ed,x ≤ VRd,s,l,x =
gMs,l,x
VRk,s,l,x = V0Rk,s,l,x · y l,V
y l,V = 1.0
gMs,l,x = ginst · gMs,l
Vcb
Ed,x [kN] V0Rk,s,l,x [kN] VRk,s,l,x [kN] gMs,l ginst gMs,l,x VRd,s,l,x [kN]
1.231 19.700 19.700 1.800 1.400 2.520 7.817
5.2.1.4 Anchor - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.5 Anchor - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080 section 7.2.2.2.2)
VRk,s,a,x
VaEd,x ≤ VRd,s,a,x =
gMs
5.2.1.6 Connection between anchor and channel - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.1.7 Connection between anchor and channel - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR
17080 section 7.2.2.2.3)
VRk,s,c,x
VaEd,x ≤ VRd,s,c,x =
gMs,ca
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.3 Concrete pry-out failure - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080
section 7.2.2.3)
VRk,cp,x
VaEd,x ≤ VRd,cp,x =
gMc
VRk,cp,x = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.4 Concrete edge failure - shear perpendicular, direction y- (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.5 Concrete edge failure - shear longitudinal, direction y+ (Anchor a1, Channel a) (Hilti method based on EN 1992-4
section 7.2.2.5, CEN/TR 17080 section 7.2.2.4)
VRk,c,x
VaEd,x ≤ VRd,c,x =
gMc
Ac,V
VRk,c,x = V0Rk,c · · y s,V · y h,V · y re,V
A0c,V
0.5
a = 0.1 (cl )f
1
0.2
b = 0.1 (dc )nom
1
c2
y s,V = 0.7 + 0.3 ≤ 1.0
1.5 · c1
0.5
y h,V = (1.5h· c ) 1
≥ 1.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.1)
2 2
2
=( ) = 0.02061
cb
N Ed
bN,s
N Rd,s,cb
2
=( ) = 0.00346
√V cb 2
+V
Ed,y
cb 2
Ed,x
bV,s
V Rd,s,cb
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.1)
k71 k71 2
2.0
= max ( ) = 0.74907
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
2.0
=( ) = 0.03747
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.02478
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.3 Anchor and connection between anchor and channel (Anchor a1)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
2.0
= max( )
a
N Ed NaEd
bN,ac , = 0.90146
N Rd,s,a NRd,s,c
2.0
= max( ) = 0.04676
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.03140
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.90146 + 0.04676 + 0.03140 ≤ 1.0
(Utilization : 98%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 16
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3.4 Concrete anchor (Anchor a1)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.70128
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.09932
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.01141
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 17
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 300 mm x 150 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 150 x 20 x 10 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
150 150
75
75
1.1 1.2 x
75
75
60 180 60
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 18
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.2FSW+1.2(FWLS+FFL)+1.2x0.8FSL
Annex 5.3
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4, longitudinal shear as per Hilti method
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = ∞ mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: -25 mm
2 Overall Result
Design ok! (Maximum utilization: 83%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.474 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] Vy [kN]
a1 11.455 -2.574
a2 8.828 -2.035
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Anchor longitudinal shear forces [kN]
Anchor Vx
a1 1.055
a2 1.055
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 11.455 18.389 63 ok
Connection anchor-channel 11.455 13.889 83 ok
Channel lip 10.440 13.889 76 ok
Channel bolt 10.440 83.733 13 ok
Flexure channel 0.474 0.852 56 ok
Pull-out 11.455 31.350 37 ok
Concrete cone 11.455 16.705 69 ok
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
10.440 125.600 1.500 83.733
Mch
Ed [kNm] MRk,s,flex [kNm] gMs,flex MRd,s,flex [kNm]
0.474 0.980 1.150 0.852
5.1.2 Pull-out failure (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
209
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
11.455 7.5 30.0 47.025 1.500 31.350
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.3 Concrete cone (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 2.534 50.240 6 ok
Flexure channel lip w/o lever arm - 2.305 13.889 17 ok
perpendicular
Flexure channel lip w/o lever arm - 1.055 7.817 14 ok
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 2.574 13.889 19 ok
Anchor - longitudinal 1.055 12.267 9 ok
Connection anchor/channel - 2.574 13.889 19 ok
perpendicular
Connection anchor/channel - 1.055 6.944 16 ok
longitudinal
Concrete pryout, perpendicular 2.574 33.290 8 ok
Concrete pryout, longitudinal 1.055 24.617 5 ok
Concrete edge - perpendicular 2.574 14.004 19 ok
Concrete edge - longitudinal 2.109 48.560 5 ok
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
2.534 2.305 1.055 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Local flexure of channel lip - shear longitudinal w/o lever arm (Fixture 1, Channel bolt 1.1, Channel a) (Hilti method
based on CEN/TR 17080 section 7.3.3.1)
VRk,s,l,x
Vcb
Ed,x ≤ VRd,s,l,x =
gMs,l,x
VRk,s,l,x = V0Rk,s,l,x · y l,V
y l,V = 1.0
gMs,l,x = ginst · gMs,l
Vcb
Ed,x [kN] V0Rk,s,l,x [kN] VRk,s,l,x [kN] gMs,l ginst gMs,l,x VRd,s,l,x [kN]
1.055 19.700 19.700 1.800 1.400 2.520 7.817
5.2.1.4 Anchor - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.5 Anchor - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080 section 7.2.2.2.2)
VRk,s,a,x
VaEd,x ≤ VRd,s,a,x =
gMs
5.2.1.6 Connection between anchor and channel - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.1.7 Connection between anchor and channel - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR
17080 section 7.2.2.2.3)
VRk,s,c,x
VaEd,x ≤ VRd,s,c,x =
gMs,ca
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.3 Concrete pry-out failure - shear longitudinal (Anchor a1, Channel a) (Hilti method based on CEN/TR 17080
section 7.2.2.3)
VRk,cp,x
VaEd,x ≤ VRd,cp,x =
gMc
VRk,cp,x = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.4 Concrete edge failure - shear perpendicular, direction y- (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.5 Concrete edge failure - shear longitudinal, direction y+ (Anchor a1, Channel a) (Hilti method based on EN 1992-4
section 7.2.2.5, CEN/TR 17080 section 7.2.2.4)
VRk,c,x
VaEd,x ≤ VRd,c,x =
gMc
Ac,V
VRk,c,x = V0Rk,c · · y s,V · y h,V · y re,V
A0c,V
0.5
a = 0.1 (cl )f
1
0.2
b = 0.1 (dc )nom
1
c2
y s,V = 0.7 + 0.3 ≤ 1.0
1.5 · c1
0.5
y h,V = (1.5h· c ) 1
≥ 1.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.1)
2 2
2
=( ) = 0.01554
cb
N Ed
bN,s
N Rd,s,cb
2
=( ) = 0.00254
√V cb 2
+V
Ed,y
cb 2
Ed,x
bV,s
V Rd,s,cb
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.1)
k71 k71 2
2.0
= max ( ) = 0.56498
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
2.0
=( ) = 0.02753
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.01820
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.3 Anchor and connection between anchor and channel (Anchor a1)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
2.0
= max( )
a
N Ed NaEd
bN,ac , = 0.68026
N Rd,s,a NRd,s,c
2.0
= max( ) = 0.03436
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.02306
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.68026 + 0.03436 + 0.02306 ≤ 1.0
(Utilization : 74%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 16
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3.4 Concrete anchor (Anchor a1)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.56783
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.07882
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00905
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 17
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 300 mm x 150 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 150 x 20 x 10 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
150 150
65
1.1 1.2 75
x
85
75
60 180 60
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 18
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 2
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
DESCRIPTION OF STRUCTURAL CALCULATION
6. Annex 6: Load capacity analysis of cast-in channel at location 3 level 12 to level 25/ Phụ lục 6: Phân tích khả
năng chịu lực của cast-in channel vị trí 3 tầng 12 đến tầng 25
Page 39/40
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.4FSW+1.4FWLP
Annex 6.1
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = ∞ mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: 25 mm
2 Overall Result
Design ok! (Maximum utilization: 20%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.020 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] V [kN]
a1 0.256 -0.148
a2 0.151 -2.541
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 0.256 18.389 2 ok
Connection anchor-channel 0.256 13.889 2 ok
Channel lip 0.407 13.889 3 ok
Channel bolt 0.407 83.733 1 ok
Flexure channel 0.020 0.852 3 ok
Pull-out 0.256 31.350 1 ok
Concrete cone 0.256 17.281 2 ok
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
0.407 125.600 1.500 83.733
Mch
Ed [kNm] MRk,s,flex [kNm] gMs,flex MRd,s,flex [kNm]
0.020 0.980 1.150 0.852
5.1.2 Pull-out failure (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
209
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
0.256 7.5 30.0 47.025 1.500 31.350
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.3 Concrete cone (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 3.660 50.240 8 ok
Flexure channel lip w/o lever arm - 3.660 19.389 19 ok
perpendicular
Flexure channel lip w/o lever arm - N/A N/A N/A N/A
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 2.541 26.400 10 ok
Anchor - longitudinal N/A N/A N/A N/A
Connection anchor/channel - 2.541 22.000 12 ok
perpendicular
Connection anchor/channel - N/A N/A N/A N/A
longitudinal
Concrete pryout, perpendicular 2.541 33.172 8 ok
Concrete pryout, longitudinal N/A N/A N/A N/A
Concrete edge - perpendicular 2.541 13.144 20 ok
Concrete edge - longitudinal N/A N/A N/A N/A
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
3.660 3.660 0.000 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.2, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Anchor - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.4 Connection between anchor and channel - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.3 Concrete edge failure - shear perpendicular, direction y- (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.1)
2 2
2
=( ) = 0.00002
cb
N Ed
bN,s
N Rd,s,cb
2
=( ) = 0.00037
√V cb 2
+V
Ed,y
cb 2
Ed,x
bV,s
V Rd,s,cb
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.1)
k71 k71 2
2.0
= max ( ) = 0.00086
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
2.0
=( ) = 0.00489
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.00000
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.3 Anchor and connection between anchor and channel (Anchor a2)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
1.0
= max( )
a
N Ed NaEd
bN,ac , = 0.01086
N Rd,s,a NRd,s,c
1.0
= max( ) = 0.11551
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.00000
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.01086 + 0.11551 + 0.00000 ≤ 1.0
(Utilization : 13%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3.4 Concrete anchor (Anchor a2)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.00136
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.08501
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00000
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 340 mm x 120 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 120 x 20 x 10 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
y
120
170 170
60
60
1.1 1.2 x
60
60
45 180 115
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.4FSW+1.4FWLS
Annex 6.2
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = ∞ mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: 0 mm
2 Overall Result
Design ok! (Maximum utilization: 86%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.281 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] V [kN]
a1 5.236 -0.305
a2 9.682 -2.384
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 9.682 18.389 53 ok
Connection anchor-channel 9.682 13.889 70 ok
Channel lip 11.902 13.889 86 ok
Channel bolt 11.902 83.733 15 ok
Flexure channel 0.281 0.852 34 ok
Pull-out 9.682 31.350 31 ok
Concrete cone 9.682 15.044 65 ok
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.2, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.2, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
11.902 125.600 1.500 83.733
Mch
Ed [kNm] MRk,s,flex [kNm] gMs,flex MRd,s,flex [kNm]
0.281 0.980 1.150 0.852
5.1.2 Pull-out failure (Anchor a2, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
209
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
9.682 7.5 30.0 47.025 1.500 31.350
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.3 Concrete cone (Anchor a2, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 3.660 50.240 8 ok
Flexure channel lip w/o lever arm - 3.660 13.889 27 ok
perpendicular
Flexure channel lip w/o lever arm - N/A N/A N/A N/A
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 2.384 13.889 18 ok
Anchor - longitudinal N/A N/A N/A N/A
Connection anchor/channel - 2.384 13.889 18 ok
perpendicular
Connection anchor/channel - N/A N/A N/A N/A
longitudinal
Concrete pryout, perpendicular 2.384 32.687 8 ok
Concrete pryout, longitudinal N/A N/A N/A N/A
Concrete edge - perpendicular 2.384 12.798 19 ok
Concrete edge - longitudinal N/A N/A N/A N/A
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
3.660 3.660 0.000 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.2, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Anchor - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.4 Connection between anchor and channel - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.3 Concrete edge failure - shear perpendicular, direction y- (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.2)
2 2
2
=( ) = 0.02020
cb
N Ed
bN,s
N Rd,s,cb
2
=( ) = 0.00531
√V cb 2
+V
Ed,y
cb 2
Ed,x
bV,s
V Rd,s,cb
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.2)
k71 k71 2
2.0
= max ( ) = 0.73433
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
2.0
=( ) = 0.06944
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.00000
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.3 Anchor and connection between anchor and channel (Anchor a2)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
2.0
= max( )
a
N Ed NaEd
bN,ac , = 0.48593
N Rd,s,a NRd,s,c
2.0
= max( ) = 0.02946
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.00000
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.48593 + 0.02946 + 0.00000 ≤ 1.0
(Utilization : 52%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3.4 Concrete anchor (Anchor a2)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.51631
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.08039
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00000
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 340 mm x 120 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 120 x 20 x 10 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
y
120
170 170
60
60
1.1 1.2 x
60
60
45 180 115
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.2FSW+1.2FWLS+1.2x0.8FSL
Annex 6.3
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = ∞ mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: 0 mm
2 Overall Result
Design ok! (Maximum utilization: 79%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.261 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] V [kN]
a1 5.304 -0.262
a2 9.096 -2.043
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 9.096 18.389 50 ok
Connection anchor-channel 9.096 13.889 66 ok
Channel lip 10.897 13.889 79 ok
Channel bolt 10.897 83.733 14 ok
Flexure channel 0.261 0.852 31 ok
Pull-out 9.096 31.350 30 ok
Concrete cone 9.096 14.922 61 ok
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.2, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.2, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
10.897 125.600 1.500 83.733
Mch
Ed [kNm] MRk,s,flex [kNm] gMs,flex MRd,s,flex [kNm]
0.261 0.980 1.150 0.852
5.1.2 Pull-out failure (Anchor a2, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
209
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
9.096 7.5 30.0 47.025 1.500 31.350
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.1.3 Concrete cone (Anchor a2, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 3.137 50.240 7 ok
Flexure channel lip w/o lever arm - 3.137 13.889 23 ok
perpendicular
Flexure channel lip w/o lever arm - N/A N/A N/A N/A
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 2.043 13.889 15 ok
Anchor - longitudinal N/A N/A N/A N/A
Connection anchor/channel - 2.043 13.889 15 ok
perpendicular
Connection anchor/channel - N/A N/A N/A N/A
longitudinal
Concrete pryout, perpendicular 2.043 32.687 7 ok
Concrete pryout, longitudinal N/A N/A N/A N/A
Concrete edge - perpendicular 2.043 12.798 16 ok
Concrete edge - longitudinal N/A N/A N/A N/A
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
3.137 3.137 0.000 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.2, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Anchor - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.4 Connection between anchor and channel - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.2.3 Concrete edge failure - shear perpendicular, direction y- (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.2)
2 2
2
=( ) = 0.01694
cb
N Ed
bN,s
N Rd,s,cb
2
=( ) = 0.00390
√V cb 2
+V
Ed,y
cb 2
Ed,x
bV,s
V Rd,s,cb
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.2)
k71 k71 2
2.0
= max ( ) = 0.61556
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
2.0
=( ) = 0.05103
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.00000
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.3 Anchor and connection between anchor and channel (Anchor a2)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
2.0
= max( )
a
N Ed NaEd
bN,ac , = 0.42892
N Rd,s,a NRd,s,c
2.0
= max( ) = 0.02165
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.00000
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.42892 + 0.02165 + 0.00000 ≤ 1.0
(Utilization : 46%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
5.3.4 Concrete anchor (Anchor a2)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.47593
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.06380
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00000
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 340 mm x 120 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 120 x 20 x 10 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
y
120
170 170
60
60
1.1 1.2 x
60
60
45 180 115
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai Q3 Fastening point: Type 2 - Location 3
Phone | Fax: | Location | Date: 23/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
DESCRIPTION OF STRUCTURAL CALCULATION
7. Annex 7: Load capacity analysis of cast-in channel at location 4 level 12 to level 25/ Phụ lục 7: Phân tích khả
năng chịu lực của cast-in channel vị trí 4 tầng 12 đến tầng 25
Page 40/40
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.4FSW+1.4FWLP
Annex 7.1
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: -25 mm
2 Overall Result
Design ok! (Maximum utilization: 29%)
IMPORTANT! Failure analysis modes evaluated by PROFIS follow EOTA TR 047/EN 1992-4. This DOES NOT include
evaluating the base material (e.g. edge-of-slab) capacity to resist compressive forces generated by the fixture. The engineer
must ALWAYS verify the base material (e.g. edge-of-slab) design is capable of resisting the applied loading.
Compressive forces generated by the fixture = 9.782 kN
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.224 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] V [kN]
a1 3.982 3.229
a2 3.110 2.971
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 3.982 18.389 22 ok
Connection anchor-channel 3.982 13.889 29 ok
Channel lip 3.609 13.889 26 ok
Channel bolt 3.609 83.733 5 ok
Flexure channel 0.224 0.852 27 ok
Pull-out 3.982 31.350 13 ok
Concrete cone 3.982 15.548 26 ok
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
3.609 125.600 1.500 83.733
Mch
Ed [kNm] MRk,s,flex [kNm] gMs,flex MRd,s,flex [kNm]
0.224 0.980 1.150 0.852
5.1.2 Pull-out failure (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
209
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
3.982 7.5 30.0 47.025 1.500 31.350
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.1.3 Concrete cone (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 3.814 50.240 8 ok
Flexure channel lip w/o lever arm - 3.814 13.889 28 ok
perpendicular
Flexure channel lip w/o lever arm - N/A N/A N/A N/A
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 3.229 13.889 24 ok
Anchor - longitudinal N/A N/A N/A N/A
Connection anchor/channel - 3.229 13.889 24 ok
perpendicular
Connection anchor/channel - N/A N/A N/A N/A
longitudinal
Concrete pryout, perpendicular 3.229 30.320 11 ok
Concrete pryout, longitudinal N/A N/A N/A N/A
Concrete edge - perpendicular N/A N/A N/A N/A
Concrete edge - longitudinal N/A N/A N/A N/A
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
3.814 3.814 0.000 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.2, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Anchor - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.4 Connection between anchor and channel - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a1, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.2)
2 2
2
=( ) = 0.00173
cb
N Ed
bN,s
N Rd,s,cb
2
=( ) = 0.00576
√V cb 2
+V
Ed,y
cb 2
Ed,x
bV,s
V Rd,s,cb
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.2)
k71 k71 2
2.0
= max ( ) = 0.06918
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
2.0
=( ) = 0.07542
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.00000
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.3 Anchor and connection between anchor and channel (Anchor a1)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
2.0
= max( )
a
N Ed NaEd
bN,ac , = 0.08221
N Rd,s,a NRd,s,c
2.0
= max( ) = 0.05405
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.00000
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.08221 + 0.05405 + 0.00000 ≤ 1.0
(Utilization : 14%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3.4 Concrete anchor (Anchor a1)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.12962
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.03475
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00000
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 220 mm x 243 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 220 x 10 x 0 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
110 110
60
122
1.1 1.2
x
183
117
122
40 140 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.4FSW+1.4FWLS
Annex 7.2
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: 25 mm
2 Overall Result
Design ok! (Maximum utilization: 54%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.000 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] V [kN]
a1 0.000 -3.762
a2 0.000 -5.555
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor N/A N/A N/A N/A
Connection anchor-channel N/A N/A N/A N/A
Channel lip N/A N/A N/A N/A
Channel bolt N/A N/A N/A N/A
Flexure channel N/A N/A N/A N/A
Pull-out N/A N/A N/A N/A
Concrete cone N/A N/A N/A N/A
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 5.730 50.240 12 ok
Flexure channel lip w/o lever arm - 5.730 19.389 30 ok
perpendicular
Flexure channel lip w/o lever arm - N/A N/A N/A N/A
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 5.555 26.400 22 ok
Anchor - longitudinal N/A N/A N/A N/A
Connection anchor/channel - 5.555 22.000 26 ok
perpendicular
Connection anchor/channel - N/A N/A N/A N/A
longitudinal
Concrete pryout, perpendicular 5.555 31.703 18 ok
Concrete pryout, longitudinal N/A N/A N/A N/A
Concrete edge - perpendicular 5.555 10.433 54 ok
Concrete edge - longitudinal N/A N/A N/A N/A
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
5.730 5.730 0.000 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.2, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Anchor - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.4 Connection between anchor and channel - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
5.2.3 Concrete edge failure - shear perpendicular, direction y- (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 220 mm x 243 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 220 x 10 x 0 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
110 110
60
122
1.1 1.2
x
183
117
122
40 140 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 22/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 1
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Specifier's comments: LV 19-25, Load case: 1.2FSW+1.2FWLS+1.2x0.8FSL
Annex 7.3
1 Input data
Channel type HAC-40 91/300 F
bolt HBC-C-N 8.8F, M16 x 50 mm
Effective embedment depth hef = 91 mm
Channel specification Length: 300 mm, anchor spacing: 250 mm, projection: 25 mm,
width: bch = 41 mm, height: hch = 28 mm
Material Anchor & Channel: hot-dip galvanized
Channel bolt: hot-dip galvanized
Europ. Tech. Assessment (ETA) ETA-11/0006
Issued I Valid 9/27/2019 | -
Standard EN 1992-4
Base material cracked, C30/37, fck,cylinder = 30.0 N/mm2, h = 180 mm
Reinforcement Exist. Reinf.: Widely spaced
Straight edge reinf. present
Reinf. to control splitting present
Tolerance data tolerance interval: -25 mm/25 mm
most unfavorable tolerance: 25 mm
2 Overall Result
Design ok! (Maximum utilization: 49%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 2
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3 Geometry
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 3
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
3.1 Fixtures/Channel bolt groups
Fixture 1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 4
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
li = 13 · I0.05
y · s0.5 » 338 [mm] ≥ s
Iy = 21463 [mm4]
s = 250 [mm]
VaEd,i = k · A'i · VEd [kN]
MEd,y,max = 0.003 [kNm]
hef = 91
a1 a2
25 250 25
Fixture bolt group
Anchor forces [kN]
Anchor N [kN] V [kN]
a1 0.036 -3.410
a2 0.023 -5.005
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 5
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5 Verifications
5.1 Verifications for anchor channels under tension loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Anchor 0.036 18.389 1 ok
Connection anchor-channel 0.036 13.889 1 ok
Channel lip 0.059 13.889 1 ok
Channel bolt 0.059 83.733 1 ok
Flexure channel 0.003 0.852 1 ok
Pull-out 0.036 31.350 1 ok
Concrete cone 0.036 15.927 1 ok
Concrete splitting N/A N/A N/A N/A
Concrete blow-out N/A N/A N/A N/A
Suppl. reinf. - steel N/A N/A N/A N/A
Suppl. reinf. - anchorage N/A N/A N/A N/A
5.1.1.3 Local flexure of channel lip (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s,l
Ncb
Ed ≤ NRd,s,l =
gMs,l
NRk,s,l = N0Rk,s,l · y l,N
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 6
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.1.1.4 Channel bolt (Fixture 1, Channel bolt 1.1, Channel a)
NRk,s
Ncb
Ed ≤ NRd,s =
gMs
Ncb
Ed [kN] NRk,s [kN] gMs NRd,s [kN]
0.059 125.600 1.500 83.733
Mch
Ed [kNm] MRk,s,flex [kNm] gMs,flex MRd,s,flex [kNm]
0.003 0.980 1.150 0.852
5.1.2 Pull-out failure (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.4)
NRk,p
NaEd ≤ NRd,p =
gMp
NRk,p = k2 · Ah · fck
Ah [mm2]
209
NaEd [kN] k2 fck [N/mm2] NRk,p [kN] gMp NRd,p [kN]
0.036 7.5 30.0 47.025 1.500 31.350
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 7
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.1.3 Concrete cone (Anchor a1, Channel a) (EN 1992-4 section 7.4.1.5)
NRk,c
NaEd ≤ NRd,c =
gMc
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si N
1+ · i
cr,N N0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc ) 1
cr,N
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5 · hef
0.5
y ch,c,N,1 = (cc ) 2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc ) 2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 8
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2 Verifications for anchor channels under shear loading
Load [kN], [kNm] Resistance [kN], [kNm] Utilization [%] Status
Channel bolt w/o lever arm 5.136 50.240 11 ok
Flexure channel lip w/o lever arm - 5.136 19.389 27 ok
perpendicular
Flexure channel lip w/o lever arm - N/A N/A N/A N/A
longitudinal
Channel bolt with lever arm N/A N/A N/A N/A
Flexure of channel lip w/ lever arm N/A N/A N/A N/A
Anchor - perpendicular 5.005 26.400 19 ok
Anchor - longitudinal N/A N/A N/A N/A
Connection anchor/channel - 5.005 22.000 23 ok
perpendicular
Connection anchor/channel - N/A N/A N/A N/A
longitudinal
Concrete pryout, perpendicular 5.005 31.678 16 ok
Concrete pryout, longitudinal N/A N/A N/A N/A
Concrete edge - perpendicular 5.005 10.421 49 ok
Concrete edge - longitudinal N/A N/A N/A N/A
Suppl. reinf. steel - perpendicular N/A N/A N/A N/A
Suppl. reinf. anchorage - N/A N/A N/A N/A
perpendicular
Suppl. reinf. steel - longitudinal N/A N/A N/A N/A
Suppl. reinf. anchorage - longitudinal N/A N/A N/A N/A
VRk,s
Vcb
Ed ≤ VRd,s =
gMs
Ed = √(VEd,y) + (VEd,x)
2 2
Vcb cb cb
Vcb
Ed [kN] Vcb
Ed,y [kN] Vcb
Ed,x [kN] VRk,s [kN] gMs VRd,s [kN]
5.136 5.136 0.000 62.800 1.250 50.240
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 9
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.1.2 Local flexure of channel lip - shear perpendicular w/o lever arm (Fixture 1, Channel bolt 1.2, Channel a) (EN 1992-4
section 7.4.2.3)
VRk,s,l,y
Vcb
Ed,y ≤ VRd,s,l,y =
gMs,l
VRk,s,l,y = V0Rk,s,l,y · y l,V
5.2.1.3 Anchor - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,a,y
VaEd,y ≤ VRd,s,a,y =
gMs
VRd,s,a,y = min(VRd,s,a,y,ETA, NRd,s,a, NRd,s,c)
5.2.1.4 Connection between anchor and channel - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.3)
VRk,s,c,y
VaEd,y ≤ VRd,s,c,y =
gMs,ca
VRd,s,c,y = min(VRd,s,c,y,ETA, NRd,s,c, NRd,s,a)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 10
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.2 Concrete pry-out failure - shear perpendicular (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.4)
VRk,cp,y
VaEd,y ≤ VRd,cp,y =
gMc
VRk,cp,y = k8 · NRk,c
NRk,c = N0Rk,c · y ch,s,N · y ch,e,N · y ch,c,N,1 · y ch,c,N,2 · y re,N
N0Rk,c = k1 · √fck · h1.5
ef
1
y ch,s,N = ≤ 1.0
nch,N
S[(1 - s ) ]
1.5
si V
1+ · i
cr,N V0
i=1
scr,N (
= 2 · 2.8 - 1.3 ·
hef
180 )
· hef ≥ 3 · hef
0.5
y ch,e,N = (cc )
cr,N
1
≤ 1.0
ccr,N (
= 0.5 · scr,N = 2.8 - 1.3 ·
hef
180 )
· hef ≥ 1.5· hef
0.5
y ch,c,N,1 = (cc )
2,1
cr,N
≤ 1.0
0.5
y ch,c,N,2 = (cc )
2,2
cr,N
≤ 1.0
hef
y re,N = 0.5 + ≤ 1.0
200
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 11
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.2.3 Concrete edge failure - shear perpendicular, direction y- (Anchor a2, Channel a) (EN 1992-4 section 7.4.2.5)
VRk,c,y
VaEd,y ≤ VRd,c,y =
gMc
VRk,c = V0Rk,c · y ch,s,V · y ch,c,V,1 · y ch,c,V,2 · y ch,h,V · y ch,90°,V · y re,V
V0Rk,c = k12 · √fck · c4/3
1
1
y ch,s,V = ≤ 1.0
nch,V
S[(1 - s ) ]
1.5
si V
1+ · i
cr,V V0
i=1
scr,V = 4 · c1 + 2 · bch
0.5
y ch,c,V,1 = (cc )
2,1
cr,V
≤ 1.0
0.5
y ch,c,V,2 = ( )
c2,2
ccr,V
≤ 1.0
hcr,V = 2 · c1 + 2 · hch
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 12
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3 Combined tension and shear loads ( EN 1992-4 section 8.3.3, Hilti method based on CEN/TR 17080 section 7.3)
Proof of interaction performed independently for steel failure of channel bolt, steel failure of the channel and concrete failure
5.3.1 Channel bolt (Fixture 1, Channel bolt 1.1)
2 2
2
=( ) = 0.00000
cb
N Ed
bN,s
N Rd,s,cb
2
=( ) = 0.00426
√V cb 2
+V
Ed,y
cb 2
Ed,x
bV,s
V Rd,s,cb
5.3.2 Point of load application - channel lip (Fixture 1, Channel bolt 1.2)
k71 k71 2
1.0
= max ( ) = 0.00067
cb ch
N M Ed Ed
bN,la,c ;
N M Rd,s,l Rd,s,flex
1.0
=( ) = 0.26490
cb
V Ed,y
bV,la,c,y
V Rd,s,l,y
2
=( ) = 0.00000
cb
V Ed,x
bV,la,c,x
V Rd,s,l,x
5.3.3 Anchor and connection between anchor and channel (Anchor a2)
k72 k72 2
bN+V,ac = max( NaEd
,
NaEd
NRd,s,a NRd,s,c ) + max ( VaEd,y Va
, Ed,y
VRd,s,a,y VRd,s,c,y ) + max( VaEd,x Va
, Ed,x
VRd,s,a,x VRd,s,c,x ) ≤ 1.0
1.0
= max( )
a
N Ed NaEd
bN,ac , = 0.00168
N Rd,s,a NRd,s,c
1.0
= max( ) = 0.22749
a
V Ed,y VaEd,y
bV,ac,y ,
V Rd,s,a,y VRd,s,c,y
2
= max( ) = 0.00000
a
V Ed,x VaEd,x
bV,ac,x ,
V Rd,s,a,x VRd,s,c,x
bN+V,ac = 0.00168 + 0.22749 + 0.00000 ≤ 1.0
(Utilization : 23%)
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 13
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
5.3.4 Concrete anchor (Anchor a2)
a a a
bN+V,c =( NaEd
NRd ) ( ) ( ) ≤ 1.0
+
VaEd,y
VRd,y
+
VaEd,x
VRd,x
1.5
=( ) = 0.00007
a
N Ed
bN,c
N Rd
1.5
=( ) = 0.33282
a
V Ed,y
bV,c,y
V Rd,y
1.5
=( ) = 0.00000
a
V Ed,x
bV,c,x
V Rd,x
has to be designed accordingly. The design of the anchorplate/bracket must be done seperatly (outside the
PROFIS software) by the engineer.
• Existing reinforcement and supplementary reinforcement as a PROFIS input should only be selected if the engineer has
verified the design of the concrete substructure complies with the associated reinforcement requirements contained in EOTA
TR 047 and/or EC2.
• Any as-built conditions which vary from the PROFIS inputs (e.g., use of alternative product, variations in supplementary
reinforcement or base material, changes in load condition...), renders the PROFIS design invalid and requires recalculation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 14
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
6 Installation data
6.1 Fixture 1
Plate type: - Bolt type: HBC-C-N 8.8F, M16 x 50 mm
Plate dimensions: 220 mm x 243 mm x 10 mm Bolt length: 50 mm
Profile: ; L x W x T = 220 x 10 x 0 mm Bolt diameter: 16 mm
Anchorplate design calculated: no Diameter hole: 18 mm
Installation torque: 0.185 kNm
110 110
60
122
1.1 1.2
x
183
117
122
40 140 40
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/Vietnam.html PROFIS Anchor Channel 1.7.5
Company: Hilti Vietnam Page: 15
Specifier: Project: Lancaster Luminaire
Address: 198 Nguyen Thi Minh Khai D3 Fastening point: Type 2 - Location 4
Phone | Fax: | Location | Date: 20/04/2021
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor Channel © 2010 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan