Professional Documents
Culture Documents
CC223921000020298F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Digital Vernier Caliper Sr. No. ------
Make Mitutoyo Location Workshop
Range / Size 0 to 150 mm Accuracy OK
Least Count 0.01 mm Visual Inspection OK
I.D. No. KAP/DVC/01
01. 0 Set 0 0 0
02. 1 0 --- ---
03. 2 0 --- ---
04. 5 0 --- ---
05. 10 0 0 0
06. 20 0 0 0 ±8.0 µm
07. 50 0 0 0
08. 100 0 0 0
09. 150 1 1 0
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by
coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020299F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Vernier Caliper Sr. No. ------
Make Mitutoyo Location Workshop
Range / Size 0 to 150 mm Accuracy OK
Least Count 0.02 mm Visual Inspection OK
I.D. No. KAP/VC/01
01. 0 Set 0 0 0
02. 1 0 --- ---
03. 2 0 --- ---
04. 5 0 --- ---
05. 10 0 0 0
06. 20 0 0 0 ±8.0 µm
07. 50 0 0 0
08. 100 0 0 0
09. 150 1 1 0
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by
coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020300F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Vernier Caliper Sr. No. ------
Make Mitutoyo Location Workshop
Range / Size 0 to 150 mm Accuracy OK
Least Count 0.02 mm Visual Inspection OK
I.D. No. KAP/DVC/02
01. 0 Set 0 0 0
02. 1 0 --- ---
03. 2 0 --- ---
04. 5 0 --- ---
05. 10 0 0 0
06. 20 0 0 0 ±8.0 µm
07. 50 0 0 0
08. 100 0 0 0
09. 150 1 1 0
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by
coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020301F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Vernier Caliper Sr. No. ------
Make Mitutoyo Location Tool Room
Range / Size 0 to 150 mm Accuracy OK
Least Count 0.02 mm Visual Inspection OK
I.D. No. KAP/VC/03
01. 0 Set 0 0 0
02. 1 0 --- ---
03. 2 0 --- ---
04. 5 0 --- ---
05. 10 0 0 0
06. 20 0 0 0 ±8.0 µm
07. 50 0 0 0
08. 100 0 0 0
09. 150 1 1 0
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by
coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020302F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Micrometer Sr. No. ------
Make Mitutoyo Location Workshop
Range / Size 0 to 25 mm Accuracy OK
Least Count 0.01 mm Visual Inspection OK
I.D. No. KAP/-MM/01
01. 0 Set 0
02. 2.5 0
03. 5.1 0
04. 7.7 0
05. 10.3 0
06. 12.9 0 ±1.0 µm
07. 15.0 0
08. 17.6 0
09. 20.2 0
10. 22.8 1
11. 25.0 1
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020303F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Micrometer Sr. No. ------
Make Baker Location Workshop
Range / Size 0 to 25 mm Accuracy OK
Least Count 0.01 mm Visual Inspection OK
I.D. No. KAP/-MM/02
01. 0 Set 0
02. 2.5 0
03. 5.1 0
04. 7.7 0
05. 10.3 0
06. 12.9 0 ±1.0 µm
07. 15.0 0
08. 17.6 0
09. 20.2 0
10. 22.8 0
11. 25.0 1
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020304F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Micrometer Sr. No. ------
Make Mitutoyo Location STD Room
Range / Size 50 to 75 mm Accuracy OK
Least Count 0.01 mm Visual Inspection OK
I.D. No. KAP/MM/03
01. 0 Set 0
02. 52.5 0
03. 55.1 0
04. 57.7 0
05. 60.3 0
06. 62.9 0 ±1.0 µm
07. 65.0 0
08. 67.6 0
09. 70.2 0
10. 72.8 1
11. 75.0 2
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020305F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Micrometer Sr. No. ------
Make Mitutoyo Location STD Room
Range / Size 75 to 100 mm Accuracy OK
Least Count 0.01 mm Visual Inspection OK
I.D. No. KAP/MM/04
01. 0 Set 0
02. 75.5 0
03. 76.1 0
04. 77.7 0
05. 80.3 0
06. 82.9 0 ±1.0 µm
07. 85.0 0
08. 87.6 0
09. 90.2 1
10. 92.8 1
11. 98.0 2
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020306F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Micrometer Sr. No. ------
Make Mitutoyo Location Workshop
Range / Size 25 to 50 mm Accuracy OK
Least Count 0.01 mm Visual Inspection OK
I.D. No. KAP/-MM/05
01. 0 Set 0
02. 25.5 0
03. 27.1 0
04. 29.7 0
05. 30.3 0
06. 32.9 0 ±1.0 µm
07. 35.0 0
08. 37.6 0
09. 40.2 0
10. 45.8 0
11. 50.0 1
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020307F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Digital Hardness Tester Sr. No. N/A
Make ------ Location -----
Range / Size HRB/HRC Accuracy/Acceptance N/A
Least Count As per Range Visual Inspection Ok
I.D. No. 8261F
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020308F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Surface Plate Model No. ------
Make Bagson Location STD Room
Range / Size 1000 x 1000 mm Accuracy ------
Least Count N/A Visual Inspection OK
I.D. No. 4364
Calibration Results
Serial Parameter Observed value in Uncertainty At 95% C.L.
No. (micron) (coverage factor k=2)
FLATNESS OF THE
1. SURFACE PLATE ±1 L+W µm
7.23 125
AS PER IS:7327
(GRADE- ‘0’)
Remarks:
These results of calibration refer to only to the particular item submitted for calibration.
The above results are valid at the time of and under the stated conditions measurement.
Calibration certificate issued for weight & measure parameters like mass, weighting balance, volumetric
equipment, measuring scales/tapes etc. are scientific purpose only and should not used for commercial.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Form No.-5.10 F-01 Page No. 1 of 1
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020309F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Instrument Details
Instrument name Profile Projector Sr. No. -------
Make Meera Metzer Location Lab
Range / Size As Per Instrument Accuracy OK
Least Count As Per Range Visual Inspection OK
I.D. No. PP-01
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No 1 Of 2
Customer name M/S: KAP FASTNERS Certificate No. CC223921000020309F
And Plot No. 82, Old IDC, Kutana Hissar Service request No & date A/02/03/03/2022
Address Road, Rohtak – 124001 Haryana, India Date of calibration 03/03/2022
Valid up to 02/03/2023
Date of issue 04/03/2022
Calibration Results
Linear (X & Y AXIS)
Serial Nominal Value In Observed Value Nominal Value In Observed Uncertainty At 95%
No. (mm) In (mm) (mm) Value In (mm) C.L.
(coverage factor k=2)
X- Axis Y- Axis
01. 10.00 9.998 10.00 10.001
02. 20.00 19.998 20.00 20.000
03. 50.00 49.997 50.00 50.000 ±4.8
04. 100.00 99.997 100.00 100.001
05 150.00 149.996
06 200.00 199.998
Calibration Results
(Magnification)
Serial Nominal Value In Observed Value In Uncertainty At 95%
No. (mm) (mm) C.L.
(coverage factor k=2)
01. 10X5 5.00 50.02 ±1.8%
02. 10X10 10.00 100.02
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No 2 Of 2
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 6 x 1-6g Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRG-01
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 6 x 1-6g No Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRGN-01
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 8 x 1.25-6g Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRG-02
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 10 x 1.25-6g NoGo Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRGN/03
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 10 x 1.5-6g Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRG/04
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 10 x 1.5-6g No Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRGN/04
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 16 x 2-6g Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRG/05
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 16 x 2-6g NoGo Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRGN/05
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 12 x 1.75-6g Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRG/09
Detail of reference standards & Major equipments used
Equipment Name Dial calibration tester
Make Elemech
Model / SR No. ----
Certificate No. CC233920000000969
Calibration Validity 03/11/22
Calibration by Asian Technology
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 12 x 1.75-6g NoGo Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRGN/09
Detail of reference standards & Major equipments used
Equipment Name Dial calibration tester
Make Elemech
Model / SR No. ----
Certificate No. CC233920000000969
Calibration Validity 03/11/22
Calibration by Asian Technology
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 6 x 1-6h Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRGH/06
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 8 x 1.25-6h Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRGH/07
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 10 x 1.5-6h Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRGH/08
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1
Instrument Details
Instrument name Thread Ring Gauge Sr. No. -------
Make Baker Location STD Room
Range / Size M 12 x 1.75-6h Go Accuracy OK
Least Count N/A Visual Inspection OK
I.D. No. KAP/TRGH/10
Remarks:
(1) Standard equipment use for calibration are traceable to national/ international standards.
(2)The reported expended uncertainty of measurement is stated as the standard uncertainty of measurement
multiplied by coverage factor k = 2 such that the coverage probability corresponds to approximately 95%.
(3)The above results are valid at the time of and under the stated conditions measurement.
(4)This certificate is refers only to the particular item submitted for calibration.
(5) Next calibration due date given as requested by the customer.
Calibrated By Approved By
(Calibration Engg./TM) (QM/TM)
(MAHIPAL) (NEERAJ TYAGI)
Format No.- 5.10 F-01 Page No. 1 of 1