Professional Documents
Culture Documents
Master Reference
Range Run 1 Run 2 Run 3 Limits
As Found
THEODOR FRIEDRICHS
Page 1 of 3
CALIBRATION CERTIFICATE
Certificate Number: VCS2023-6602
VC-RF-T-05,REV.NO:03, REV.DATE : JUNE 2023
Remarks:
1. Averages of minimum three readings are reported.
2. Suggested due date and test point were given based on customer requirements.
3. These results are obtained at the time of calibration.
4. The user should determine the suitability of the instrument for its intended use.
5. Uncertainty of measurement at 95% confidence level by multiplying coverage factor k = 2.
6. Condition of instrument found satisfactory during receipt.
7. Our masters are directly calibrated through ISO/IEC 17025 accredited calibration lab having direct traceability with national /
International standard.
8. Vertex Calibration Laboratory is accredited in accordance with the recognized International Standard as per ISO/IEC 17025:2017.
9. UUC- Unit Under Calibration
10.Pass / Fail criteria is decided by comparing the error of the unit under calibration and its associated by measurement uncertainty with
the tolerance specified by the manufacturer / customer.
11.Accuracy, tolerance and acceptance criteria stated as per customer requirements
12.Any hand written corrections (except @) or photocopies of the report invalidate this certificate.
13.Results reported outside the scope of accreditation are mark with asterisk (*).
Calibration cycle are resulting due dates were submitted/approved by the customer.Any number of factors may cause an instrument to drift out of tolerance before the next scheduled of
calibration.Recalibration cycles should be based of frequency of used, environmental condition and customer's established systmatic accuracy.The information on this report, pertains only to the
instrument identified.
CALIBRATION RESULT
Certificate Number: VCS2023-6602
VC-RF-T-05,REV.NO:03, REV.DATE : JUNE 2023
Temperature Measurement
Master
Range Reference As UUC As Found UUC As Left Deviation Tolerance Result Uncertainty
Found
-50 to +250 °C -10.00 °C -10.1 °C -10.1 °C -0.10 °C ± 0.50 °C PASS ± 0.2500 °C
-50 to +250 °C 0.00 °C 0.2 °C 0.2 °C 0.20 °C ± 0.50 °C PASS ± 0.2500 °C
-50 to +250 °C 25.00 °C 24.9 °C 24.9 °C -0.10 °C ± 0.50 °C PASS ± 0.2500 °C
-50 to +250 °C 50.00 °C 49.9 °C 49.9 °C -0.10 °C ± 0.50 °C PASS ± 0.2500 °C
-50 to +250 °C 100.00 °C 99.9 °C 99.9 °C -0.10 °C ± 1.00 °C PASS ± 0.2500 °C
-50 to +250 °C 150.00 °C 149.7 °C 149.7 °C -0.30 °C ± 1.00 °C PASS ± 0.2500 °C
-50 to +250 °C 200.00 °C 200.1 °C 200.1 °C 0.10 °C ± 1.00 °C PASS ± 0.2500 °C
-50 to +250 °C 240.00 °C 240.1 °C 240.1 °C 0.10 °C ± 1.00 °C PASS ± 0.2500 °C
***End of Calibration***
Where statements of conformity are made in this report, the following decision rules are applied:
PASS - Results ± expanded uncertainty within limits / specification
FAIL - Results ± expanded uncertainty exceeds limit / specification
INDETERMINATE - Results ± expanded uncertainty overlaps limit / specification