Professional Documents
Culture Documents
METHOD STATEMENT
for Installing Tiles and Repairs
(Ceramic, Porcelain and Natural Stones)
1
JAVTolentino
Project: Owner: Revision No:
TABLE OF CONTENTS
Pages
1. INTRODUCTION …………………………………………………………………………… 3
2. SCOPE ……………………………………………………………………………………….. 3
3. PURPOSE ………………………………………………………………………………………. 3
4. MATERIALS ………………………………………………………………………………………. 3
5. RESPONSIBILITIES …………………………………………………………………………… 4
7. REPAIRS …………………………………………………………………………………… 6
8. SAFETY ………………………….………………………………………………............ 8
9. REFERENCES ………………………….………………………………………………............ 8
2
JAVTolentino
Project: Owner: Revision No:
1. INTRODUCTION:
One of the many advantage of Tiles is how easy it is to keep clean. There is no need for
harsh detergents, powders, or chemical cleaners. Tile does not require repetitive sealing
either. An installation of tile will mean simple maintenance for the lifetime of the
application.
2. SCOPE:
The purpose of this Method Statement for Installation of Floor and Wall Tiles is to outline
and describe in details the procedure, material and labor required to undertake the work
or activity in a safe and controlled manner. This activity should be performed with strict
compliance and implementation of Safety Requirements and Procedure, standard
practices, and project specification to complete the work.
3. PURPOSE:
It makes the surface even, smooth and easy to maintain. Flooring, also called as tiling
finishes, starts once the structure work of the house is completed it also includes the wall
of kitchens and bathroom together with some recreational area and kiosk. It is mostly
done after the first phase of the Electrical Finishes, Plumbing finishes and Joinery finishes.
4. MATERIALS:
3
JAVTolentino
Project: Owner: Revision No:
5. RESPONSIBILITIES:
Responsible in ensuring that all activities are carried out safety patrol at the site.
Establishing the site safety plan, conducting continuous safety inspection and stop
any work deemed unsafe and a risk to personal. Taking action to rectify the unsafe
condition and report to Safety manager
5.2 SURVEYOR
Responsible in all Items on site are Setting out in its location (coordinates) and levels
in accordance with approved drawing and take care all worker to be work with their
responsibilities and make a decision when some non-conformance occurring their
report to Surveyor manager.
Have the responsibility of the management or control of a work place, with their
area of authority, and must ensure this procedure is implemented. They shall
maintain Hazard and Risk register and appropriate signage for their work place; and
shall ensure that site Senior Engineer assigned for the management and execution of
work within their area of authority.
Have the responsibility of the management, supervise and control of a work place,
with their area of authority, and must ensure this procedure is implemented. They
shall maintain Hazard and Risk register and appropriate signage for their work place;
and shall ensure that site Senior Engineer assigned for the management and
execution of work within their area of authority. Always report the progress of work
to Project Manager.
Has The responsibility in all activities on site are carried out in accordance the
construction drawing and take care all worker to be work with their responsibilities
and make a decision when some non-conformance occurring their report to senior
engineer.
4
JAVTolentino
Project: Owner: Revision No:
6. WORK PROCEDURES:
5
JAVTolentino
Project: Owner: Revision No:
6.2 Application
6
JAVTolentino
Project: Owner: Revision No:
6.2.3 Grouting
7. REPAIRS:
Find a replacement tile that matches. Flooring contractors often leave spare tiles in
the garage or storage room for when the homeowner might need to repair tile
mishap.
Choose a matching grout. Borrow colored grout samples from a well-stocked
flooring supply store and bring it home to find the closest match.
7
JAVTolentino
Project: Owner: Revision No:
Remove the old tile completely. Be careful not to damage any of the surrounding
tiles.
►Use an electric drill with a masonry bit to drill a diagonal series of small holes into
the cracked tile, keeping drilled holes less than 1 inch (2.54 cm) apart.
►Split the tile through the horizontal hole-line by using a ball-peen hammer to tap a
cold chisel into the tile. Tap very lightly so as not to crack neighboring grout joints.
►Remove the loosened pieces. Use a flat bar to pry up any shards that you cannot
get up by hand.
►Scrape the remaining old mortar from the subfloor using a stiff-bladed scraper. It
is not important that you get every last bit up. Just make sure the area is fairly clean
of mortar.
►Vacuum up any loose dirt or debris
Set the replacement tile. Mix the thin-set mortar to a pancake batter consistency.
Let sit for 5 minutes, stir again, and begin spreading. Use a notched trowel to spread
mortar onto the subfloor and lay the new tile in. Use a level to ensure tile is laying
perfectly flat and also to determine that the newly set tile is flush with surrounding
tiles.
Grout the area according to the grout manufacturer's directions. Generally, it is
done the following way:
►Mix your grout in a clean container with fresh water. Slowly add a little bit of
water, mix and then repeat until you reach a consistency of pancake batter.
►Using a grout float, scoop out a bit of grout. Place the float at a 45-degree angle
and in diagonal strokes spread the grout in the gaps between the tiles.
►After 20-30 minutes your grout should start to harden, and you can clean the
surface of tiles with a wet sponge. You may need to do 2-3 rounds of cleaning.
8. SAFETY:
All works shall comply with safety procedure or instruction as set out in project
safety plan and municipality rules and regulations. All safety recommendations as
advised by the approved sub-contractor.
Basic PPE to be worn by all staff or laborers.
Provide lighting when working at night.
8
JAVTolentino
Project: Owner: Revision No:
9. REFERENCES:
ANSI A108
ANSI A118
9
JAVTolentino