Professional Documents
Culture Documents
Working Cast and Die Crown 1
Working Cast and Die Crown 1
Working cast
is the positive replica of the prepared teeth, ridge areas, and the other parts of the dental
arch. - The accuracy of a cast and die is a function of completeness and accuracy of the
impression.
Die
Positive reproduction of the prepared tooth and consists of a suitable hard substance of
) sufficient accuracy ( usually an improved stone , resin or metal
اما بقا ال ألسنان نفسها الي انا عملت لها preparedسوا واحده او اكتر هيكون اسمها dieوهي دي الي wax pattern
ويدخلها في ال casting machineوبيسيح ال waxويدخل مكانه metalعشان يطلع لي ال crown or inlay or onlay
الي انا عاوز اعمله في االخر يلزمني أن ال dieتكون removableعشان لما اجي اعمل عليها ال wax patternيبقا
سهل تحركها وتظبط ال marginكويس
طيب عشان اطلع كاست حكاية اي الي الزم يكون متوفر فيه ؟ ) There are requirements for good casts
) عشان يطلع كراون مظبوط في النهايةcast )في شوية متطلبات المفروض تتحق في ال
بتقولي ازاي هتفيدني بايه مش انا ممكن اعملEdentulous area لكل حاجة زي ال الstable dimension الزم تكون
فالزم يكون موضحها لي كويس بكل تفاصيلها وكمان الpontic والretainer بينها وبين الrelation وفيbridge
عشان أنا هحط الكاست دا بعد كدا علي ارتكيولتور فالزم اكونocclusal لstable طبعا و كمانprepared tooth
كويسdimensions ظابطه ال
–It must reproduce both prepared and unprepared tooth
الزم بديني صورة دقيقة من األسنان الي انا حضرتها أو الي االسنان الي في الفم كلها
–Unprepared teeth adjacent and opposing to the preparation must be free of avoid
crown خاليه من اي مشاكل الن عشان ابني الجزء الخاص بالadjacent and opposing وكمان الزم تكون األسنان الي
عشان يعملocclusion وكمان الContact area عشان يظبط الneighboring tooth and opposing محتاج
صحbuild up
–surface of teeth involved in anterior guidance and the occlusal surfaces of all unprepared teeth
must allow for precise articulation of the opposing cast
و ميبقاش فيه ايaccurate فالزم تكونanterior teeth من الocclusion الزم الجزء الي داخل في ال
عموماocclusion لي في الguide هو الanterior teeth بتاع الocclusion ودا عشان الfracture
صح وبالتالي هياثر ليarticulation فمش هعرف هعملocclusion ف لو في اي مشكلة فهيأثر علي ال
علي كل الخطوات بعد كدا
–All relevant soft tissues should be reproduced in the working cast ( Edentulous
spaces and residual ridge contours that will be involved in the fixed Prothesis )
بالنسبة لي والمعملguide هو الprepared tooth الي حوالين الsoft tissue المفروض أن كل ال
ميكنش نازل وضاغط علي الover contour ميبقاشmargin عشان الcrown لbuild up بيعمل
موجودsoft tissue فعشان كدا الزم يكون الgingiva
type III هتكون ابتدأ منdie 📌 اما األنواع الي انا هستخدمها أن اعمل بيها ال
Type III dental stone
Type IV: High-strength dental stone.
Type V: High-strength high-expansion stone. دا النوع الي يهمني
The physical properties of die stone are improved over those of dental stone because less
water is needed to obtain a sufficiently fluid mix.
يستخدم النسب دي مهم اني اعرفها ولكن ممكن تختلف تبعا لكل شركةstone للmix عشان اعمل
100 g of plaster requires 45 to 50 mL of water,
100g of dental stone requires 3o to 35 ml of water
100 g of die stone requires 20-25 ml.of water, depending on the particular Brand.
بشكلmix وابدا اعملpowder االول وبعدين احط عليه الwater وأحط الrubber بجيب الhand mixing ال
عشان كدا الزم أخرجهاaccuracy ودي طبعا هتاثر علي الmix موجوده جوا الair bubbles ولكن بيكون فيmanually
air bubbles واطلع بيه الvibrating فبستخدم جهاز اسمه
vacuum mixing عن طريقmix أو الطريقة التانية اعمل ال
powder والstone جهاز بحط فيه ال
air bubbles تطلع الtubes وبنركب عليها حاجة زيpowder والstone كدا بحط فيها الplastic boil فبركب
الي جواها
high accuracy بيطلعmix وال
Advantages of Gypsums
– Reasonable Dimensional accuracy
– Good surface details reproduction with type IV , Type V Gypsum products
– Inexpensive
– Easy for use
greatest disadvantage
ولكن حل المشكلة دي بإضافة بعض المواد عشان تزود الabrasion لpoor resistance مشكلته الوحيده هو أن عنده
colloidal silica(Gypsum Hardeners) زي الhardness and abrasion resistance
cyanoacrylate زيlow viscosity resin وكمان ممكن اضيف
is its relatively poor resistance To abrasion. Attempts to increase surface hardness and abrasion
Resistance have included the use of so called ‘gypsum hardeners’ (colloidal silica) improves the
abrasion resistance. Another method Is by impregnating the surface of the die with a low
viscosity resin
Cyanoacrylate or epoxy resins etc. A solution of 10% polystyrene
stone ويستخدمه عشان يطلع لي الGypsum علي الresin وهو اني اضيف الresinrock وفي نوع تاني اسمه
عاليةresistance abrasion بتاعي كويس وكمان عندهhardness بتاعي ال
Amalgam dies :
– These dies are made in impressions made With impression compound in the copper band
procedure.
؟ تعرف ليه ؟؟ ألن االملجم وانا بعملهamalgam مينفعش اصبه بالrubber base الي انا باخده بالImpression ال
rubber علي حاجةcondensation فمينفعش اعملcondenser باستخدام الcondensation بيعمد علي ال
Impression عشان اخد الcompound فعشان كدا بستخدم في الحالة دي ال
ألن هيمسك في األسنان ومش هيطلع ف انا باخد امبرشنcompound لكل االسنان بالImpression كمان مينفعش اخد
undercut بس وشرطها كمان أن تكون االسنان دي خالية من أيprepared لالسنان ال
يرجع سوفت تاني عشان ميكسرش السنةImpression الحل لو االمبرشن مسك علي السنة اني احط ماء دافئ وهيخلي ال
single tooth ودي بيتستخدم بس لو عنديcopper ring الي عبجيب حاجة زي ال
condensation اقدر اعملmix فبالتالي بعد ما اعملvery hard وطبعا بيكونcompound بدأ اخد امبرشن طبعا بال
preparation tooth فبالتالي يطلع يديني شكل ال
اليdetails بيتشكل بالضغط بتاعي وبيأثر علي الcondensation فلما اجي اعملrubber base اما لو استخدمت ال
بالنسبه لناaccurate انا محتاجاها تكون
Advantages
• Produces a hard die
• Adequate reproduction of fine details and sharp margins.
hard بتاخد مواصفات دقيقة وكمان هي
Disadvantages
Expansion so its dimensions not accurate
• Can only be picked into a rigid impression
• Time consuming process
• High thermal conductivity can cool a wax pattern. This can be Overcome by warming the
die.
Resin dies
Resin materials have Also been used for fabrication of dies for the preparation of inlays,
Crowns, fixed partial dentures using the indirect technique. These Materials show good
properties of strength, hardness, abrasion,
Advantages
1. Better strength and abrasion resistance than high strength Stone dies.
Not need expansive equipment
2. Dimensionally stable and can be cured at room temperature.
3. Ideal material for reproducing details can reproduce groove Depth up to 20 µm.
Disadvantages
–More Expansive than Gypsum
–shrinkage
Undergoes shrinkage during polymerisation which is approxi-Mately the same as
expansion with stone dies. Hence, prosthesis
layer by later دا اني بحطهshrinkage بنتغلب علي ال
أوsilver طريقة صعبه أن حد يعملها والي بعتمد فيها علي الترسيب الكهربي ( الكاثود واالنود) اني احط في جهة ال
copper والsilver مادة تجذب الprepared وبدهن علي ال جزء الcast والعمود التاني بيكون الcopper ال
Bink wax وكمان ب غطي االسنان الي مش عاوزه يترسب عليها ب
ألن بيدوم فترة طويلة جدا مبيتاثرش وطبعا وطبعا بيستغرقresearch وطبعا دا غالب بيستخدم غالبا ألغراض ال
وقت طويل عشان اعمله
Advantages
1. Dimensionally stable.
2. Strong.
4. Can be saved for many years.
Disadvantages
Time consuming nearly 12 hour
Performed slowly
★Silicone Impression . Are difficult to electroplate evenly Because of their low surface energies.
Thank yo u