Professional Documents
Culture Documents
01.ANSYS Trusses
01.ANSYS Trusses
Static analysis
A structure consisting of two equal steel bars, each of length l and cross-sectional area A, with hinged ends is
subjected to the action of a load F. Determine the stress, σ, in the bars and the deflection, δ, of point 2. Neglect the
weight of the bars as a small quantity in comparison with the load F.
Thanh chỉ chịu kéo/nén Trusses
F = 5000 lb Nội lực chỉ có thành phần lực dọc Nz
N z 5000
N z 5000 (lb) z 10000 (lb/in2)
F = 5000 lb A 0.5
2 N Nz
F F
z
EA EA
Working area
Main menu
Model control
Global Coordinate toolbar
System
Current setting
Pre-Processor
stage
Visualization of results
displacements
stress
safety factor
…
7 21.07.2021 MaiDucDai_Special subject on CAE Aalysis_Static Analysis of Trusses FMD Dept.
Change project title
Utility menu File Change Title…
Project title
Input cross section area (nhập giá trị diện tích tiết diện ngang thanh)
Its should be noted that a consistent unit system much be used
Cần sử dụng đơn vị tương thích
Linear > Elastic > Isotropic: vật liệu tuyến tính, đồng nhất đẳng hướng
EX: Young’s modulus – modul đàn hồi
PRXY: Poisson’s ratio – Hệ số Poisson
Cần sử dụng đơn vị tương thích
12 21.07.2021 MaiDucDai_Special subject on CAE Aalysis_Static Analysis of Trusses FMD Dept.
Consistent unit systems (hệ đơn vị tương thích)
Mass: kg
Density: kg/m3
Length: m
SI Stress: Pa (N/m2)
Time: s
Gravity: 9.81 m/s2
Force: N
There is no unit system is defined in ANSYS Classic, user have responsibility on using consistent
units for their input parameters.
Reference: https://www.dynasupport.com/howtos/general/consistent-units
- Keypoints:
x y z
a 2 cos , b sin 1 0 0 0
y cos
2 sin 0
a
3 2 cos 0 0
1 x 3
-Lines
b Keypoint #1 Keypoint #2
2 1 1 2
2 2 3
Nếu create trực tiếp các nodes, elements (FEM model) không cần bước meshing
Mặc định, đơn vị đo góc RAD, bên dưới hướng dẫn cách chuyển sang DEGREE
Meshing
Node #1
Node ID
Nodal coordinates
Node #2
node #1 node #3
element #1 element #2
Front view
Fit view
Nodes (nplot)
Elements (eplot)
Geometrical model
Meshing
FEM model
Generate Apply
Nodes, Elements BC’s
Keypoint #1
Keypoint ID
Keypoint #2 Keypoint coordinates
Keypoint #1 Keypoint #3
Keypoint #2
Line #1 Line #2
Step 1: Định nghĩa số phần tử trên line 1 phần tử/line cho hệ thanh kéo/nén
Step 1
Step 2
Step 2: Chọn button Mesh chọn tất cả các line OK (option “lines” phải được chọn trong listbox Mesh)
Step 1: trên hộp thoại MeshTool chọn button Clear chọn các phần tử cần delete
Step 2: OK
Step 1
Step 2
Step 3
Step 1: Chọn các nodes #1, #3 (các nodes cần áp ràng buộc)
Step 2: Chọn ALLDOF trong listbox DOFs to be constrained
Step 3: Nhập 0 vào box Displacement value
Step 3: Ok
Main Menu Preprocessor Load Define Loads Apply Structural Force/Moment On Nodes
Step 3: Ok
Length: in
Force: lb (pound)
Output:
Displacement: in
Force: lb
Stress: psi (lb/in2)
UY = - 0.12 in
UX = 0 in
2500 lb 2500 lb
4330.1 lb 4330.1 lb
Node #1 Node #3
5000 lb (input)
Phần tử #1, Nội lực dọc trục = 5000 lb, ứng suất pháp = 10.000 lb/in^2