Professional Documents
Culture Documents
Bảng 3: Thành phần hóa học dựa trên phân tích mẻ nấu— % Maximum
Grade C Si Mn P S N
CB240-T
0.05 0.05
CB300-T
a:
b: Other
Alloy CEV formulae
elements, such and values
as Cu, mayMo,
Ni, Cr, be used byTi
V, Nb, agreement between
and Zr, may the manufacturer
be added by agreementand purchase
between the manufacturer and
purchaser
Bảng 4: Thành phần hóa học dựa trên phân tích mẻ nấu— Sai số cho phép
P ≤ 0.05 +0.008
S ≤ 0.05 +0.008
CƠ TÍNH
Tính uốn-ISO 15630-1
Giới hạn
chảy trên Bền kéo
Steel grade Rm/ReH Giãn dài (%)
ReH (Rm,Mpa)
(N/mm2)
Kích cỡ
Bảng 2 — Kích thước, khối lượng 1m chiều dài và sai lệch cho phép
Diện tích mặt cắt Khối lượng 1m dài
=0.00785 x An
Đường kính thanh danh ngang danh nghĩa An,
nghĩa, (d, mm) mm2
An=0.7854 x d2 Yêu cầu (kg/m) Sai lệch (%)
6 28.3 0.222 ±8
8 50.3 0.395 ±8
10 78.5 0.617 ±6
12 113 0.888 ±6
14 154 1.21 ±5
16 201 1.58 ±5
18 254.4 2 ±5
20 314 2.47 ±5
22 380 2.98 ±5
25 490.9 3.85 ±4
28 615.8 4.83 ±4
32 804.2 6.31 ±4
36 1017.9 7.99 ±4
40 1256.6 9.86 ±4
Composition (%)
UNS
Desig- Type
nationA C P Si Other
Mg B SB Cr Ni
max max max Elements
AUSTENITIC
S20300 XM-1 0.08 5.0-6.5 0.04 0.18-0.35 1.00 16.0-18.0 5.0-6.5 Cu 1.75-2.25
S30300 303 0.15 2.00 0.20 0.15 min 1.00 17.0-19.0 8.0-10.0 -
S30310 XM-5 0.15 2.5-4.5 0.20 0.5 min 1.00 17.0-19.0 7.0-10.0 -
S30323 303 Se 0.15 2.00 0.20 0.06 1.00 17.0-19.0 8.0-10.0 Se 0.15 min
Mo 0.40-0.60
S30345 XM-2 0.15 2.00 0.05 0.11-0.16 1.00 17.0-19.0 8.0-10.0
Al 0.60-1.0
MARTENSITIC
S41600 416 0.15 1.25 0.06 0.15 min 1.00 12.0-14.0 - -
S18200 XM-34 0.08 2.50 0.04 0.15 min 1.00 17.5-19.5 - Mo 1.50-2.50
Mo 2.00-2.50
Ti 0.30-1.00
S18235 - 0.025 0.50 0.03 0.15-0.35 1.00 17.5-19.5 1.00
N 0.025 max
C+N 0.035 max
B
Maximum unless otherwise noted
CƠ TÍNH
Table 3 Mechanical Test Requirements
A
Condition B applies only to wire annealed and cold worked to produce high
EN-standard EN-standard
SAE grade UNS
Steel no. k.h.s DIN Steel name
1.4109 X65CrMo14 440A S44002
X1NiCrMoCuN25-20-
1.4529 N08926
7
X1CrNiMoCuN20-18-
1.4547 254SMO S31254
7
ISO 6935-1: Steel for the reinforcement of concrete — Part 1: Plain bars
Chemical composition based on cast analysis — Maximum values of mass fractions, in
percentage
Grade C Si Mn P S N CEVa
B240A-P
B240B-P
B240C-P
0.06 0.06
B300A-P
B300B-P
B300C-P
B240D-P
0.05 0.05
B300D-P
B420D-P
0.3 0.55 1.5 0.04 0.04 0.012 0.56
B420DWPb
a:
b: Other
Alloy CEV formulae
elements, such and values
as Cu, mayMo,
Ni, Cr, be used byTi
V, Nb, agreement between
and Zr, may the manufacturer
be added by agreementand purchase
between the manufacturer and
purchaser
Chemical composition based on product analysis —
Permissible deviation of the product analysis in percentage by mass
Permissible deviation in
Specified maximum value in cast product analysis from the
Elements
analysis in Table 3 specified limits of the cast
analysis in Table 3
C > 0.25 +0.03
Si ≤ 0.6 +0.05
Mn ≤ 1.65 +0.06
≤ 0.05 +0.008
P
> 0.05 +0.01
≤ 0.05 +0.008
S
> 0.05 +0.01
By agreement between the manufacturer and purchaser, the type of elongation shall be selected
between A5 and Agt. If the type of elongation is not specified by agreement, Agt should be used
By agreement between the manufacturer and purchaser, the type of elongation shall be selected
between A5 and Agt. If the type of elongation is not specified by agreement, Agt should be used
Dimension
Table 2 — Dimensions, mass per unit length and permissible deviations
Mass per unit length
Nominal cross-sec An, =0.00785 x An
Nominal bar diameter,
mm2
(d, mm)
An=0.7854 x d2 Requirement (kg/m) Deviation (%)
6 28.3 0.222 ±8
8 50.3 0.395 ±8
10 78.3 0.617 ±5
12 113 0.888 ±5
14 154 1.21 ±5
16 201 1.58 ±5
20 314 2.47 ±5
22 380 2.98 ±5
manufacturer and
0.01776 0.6 0.013333 0.75
254.4696 1.9939
201.0624
JIS G3505: 2004 LOW CARBON STEEL WIRE RODS
Grade C Si Mn P S
SWRM 6 0.08 0.6 0.04 0.04
SWRM 8 0.1 0.6 0.04 0.04
SWRM 10 0.08 - 0.13 0.3 - 0.6 0.04 0.04
SWRM 12 0.1 - 0.15 0.3 - 0.6 0.04 0.04
SWRM 15 0.13 - 0.18 0.3 - 0.6 0.04 0.04
SWRM 17 0.15 - 0.2 0.3 - 0.6 0.04 0.04
SWRM 20 0.18 - 0.23 0.3 - 0.6 0.04 0.04
SWRM 22 0.2 - 0.25 0.3 - 0.6 0.04 0.04
Killed steel --->K: SWRM 10 K
Grade C Si Mn P S
SWRM 2 0.04 0.6 0.04 0.04
SWRM 4 0.06 0.6 0.04 0.04
For profile wires of high strength for welded steel wire fabrics: Mn 0.6%min (preferable 0.6-0.9%)
Binding wire,
SWRM 6/1006 420 30
Annealed wire
Telegraph wire,
SWRM 8/1008 440 25
nails
Galvanized wire,
SWRM 10/1010 460 23
Barbed wire
Concrete
SWRM 22/1022 600 20
Reinforcement
Commercial
-
1020
DS
N
vẽ dây tốt
2. Chemical compostion
Table 2 - Chemical composition (max % by mass)
C P S Na
Cast Analysis 0.220 0.050 0.050 0.012
Product Analysis 0.240 0.055 0.055 0.014
a: Higher Nitrogen contents are permissible if sufficient quatities of nitrogen binding elements are present.
Ce=C+Mn/6+(Cr+V+Mo)/5+(Cu+Ni)/15
3. Mechanical Properties
Table 4 — Tensile properties
Nominal YS, Re Rm/Re Total EL at max
thickness, Grade force Agt
d (mm) (min, MPa) min
≤ 12 250 250 1.15a 5
<8 500 500 1.02 1
≤8 500 500 1.05 2.5
Values of Re specified are characteristic with p=0.95 (95%).
Values of Rm/Re and Agt specified are characteristic with p=0.9 (90%).
Calculate the values of Rm and Re using the nominal cross section erea.
For YT (Re), the upper YT (Reh) shall apply. Determine the YT (Re) from 0.2% proof strength (Rp0.2) if the yield p
Rebend test: max 4d, d (nominal thickness) * Note: Bend the test pieces through an angle of 90o, age
4. Dimensions
Table 4 — Cross sectional area and mass
Nomimal demensions
mass)
Cu Ce
0.800 0.42
0.850 0.44
ents are present.
525
ough an angle of 90 o, age the test pieces and bend back by at least 20 o
d≤6 0.035
p=0.95 (95%)
6 < d ≤ 12 0.04
rom the nominal diameter. The
ual to 45 o, and the transition from
of between 35 o-75o
16120-2
BẢNG TỔNG HỢP CÁC MÁC THÉP CHO WIRE R
Steel designation European material No. Steel designation n/nr/ya Steel designation n/nr/ya
SWRH42A nr
C42D 1.0541 C42D y
SWRH42B nr
SWRH47A nr
C48D 1.0517 C48D y
SWRH47B nr
C50D 1.0586 nr C50D y
SWRH52A nr
C52D 1.0588 C52D y
SWRH52B nr
C56D 1.0518 nr C56D y
SWRH57A nr
C58D 1.0609 C58D y
SWRH57B nr
C60D 1.061 nr C60D y
SWRH62A nr
C62D 1.0611 C62D y
SWRH62B nr
C66D 1.0612 nr C66D y
SWRH67A
C68D 1.0613 nr C68D y
SWRH67B
C70D 1.0615 nr C70D y
SWRH72A
C72D 1.0617 nr C72D y
SWRH72B
C76D 1.0614 nr C76D y
SWRH77A
C78D 1.062 nr C78D y
SWRH77B
C80D 1.0622 nr C80D y
SWRH82A
C82D 1.0626 nr C82D y
SWRH82B
C86D 1.0616 C86D y
C88D 1.0628 C88D y
C92D 1.0618 C92D y
Note:
a: Độ lệch khi phân tích hóa học (phân tích bằng nhiệt) theo như tiêu chuẩn ISO 16120-2: n: không, nr = không phù hợp, y = phù hợp
THÉP CHO WIRE ROD
Thành phần hóa học
Nguyên tố Mác thép Độ lệch cho phép
TCVN 1651-1:2008 CB240-T Min 380 Min 240 20 20 20 20 20 20 20 20 Min (BK/GHC: 1.46)
ISO 16120-2 2011 C4D to C20D Không yêu cầu, thỏa thuận Dung sai ± 80
ASTM A581/A581M-95b:
2014
S18235 A 415-620 - - - - - - - - -
S18235 B 550-830 - - - - - - - - -
ASTM A581/A581M-95b:
2014
All (Except S18235 A) 585-860 - - - - - - - - -
TCVN 1651-1:2008 - - - - - - - - - - -
BS 4482-2005 - - - - - - - - - - -
ISO 16120-2 2011 C72D to C92D Không yêu cầu, thỏa thuận
4 TCVN 1651-1:2008 - - - - - - - - - - -
ISO 6935-1:2007 - - - - - - - - - - -
BS 4482-2005 - - - - - - - - - - -
2. UỐN
Độ bền uốn, d, min (%)
STT Tiêu chuẩn Grade Ghi chú
10 13 16 19 22, 25 29, 32 36 43, 57
ISO 16120-2 2011 C4D To C20D Không yêu cầu, thỏa thuận
ASTM A581/A581M-95b:
2014
S18235 A - - - - - - - -
SR295 - - - - - - - -
SD295B - - - - - - - -
500 (< 8) - - - - - - - -
BS 4482-2005
500 (≥ 8) - - - - - - - -
ISO 16120-2 2011 C26D To C70D Không yêu cầu, thỏa thuận
S18235 B - - - - - - - -
ASTM A581/A581M-95b:
2014
All (Except S18235 A) - - - - - - - -
BS 4482-2005 -
ISO 16120-2 2011 C72D To C92D Không yêu cầu, thỏa thuận
4 TCVN 1651-1:2008 - - - - - - - - -
ISO 6935-1:2007 - - - - - - - - -
BS 4482-2005 - - - - - - - - -
3. Yêu cầu về chất lượng bề mặt sản phẩm - Tiêu chuẩn ISO 16020-1:2011
Bị trầy do các cuộn ma sát
Bị trầy do ma sát vào sàn bê tông Bị trầy do quá trình xếp chồng bị ma sát vào nhau
vào nhau
TCVN 1651-1:2008
Chiều dài theo tiêu chuẩn
(m)
Dung sai (mm)
6
0/+100
0/+100
12
6 0.222 ±8 ±6 0.222 ±8
8 0.395 ±8 ±6 0.395 ±8
18 1.994 ±5 ±4.5 2 ±5
25 - - ±4.5 3.85 ±4
28 - - ±6 ±4.5 4.83 ±4
32 ±6 ±4.5 6.31 ±4
0.96 max
36 ±6 ±4.5 7.99 ±4
40 ±6 ±4.5 9.86 ±4
500 (< 8)
BS 4482-2005 Xem thông tin chi tiết sheet TC
500 (≥ 8)
TCVN 1651-1:2008 - - - - - - -
3 JIS G 3112 : 2010 SD390 0.29 0.55 1.80 0.040 0.040 0.55
BS 4482-2005 -
JIS G 3112 : 2010 SD490 0.32 0.55 1.80 0.040 0.040 0.60
4 TCVN 1651-1:2008 - - - - - - -
ISO 6935-1:2007 -
- -
380-520 235
~290 250
415-620 -
Min 440 -
- -
510 500
525 500
550-830 -
585-860 -
- -
- 420-540
560 390-510
- -
795-1000 -
620 490-625
- -
- -
- -
- -
- -
Soi dưới kính hiển vi để xem các lỗi bề mặt bị gián đoạn trong quá trình sản xuất
Tiêu chuẩn D Dạng
TCVN 1651-1 6 Coil/Bar
TCVN 1651-1 8 Coil/Bar
TCVN 1651-1 10 Coil/Bar
TCVN 1651-1 12 Bar
TCVN 1651-1 14 Bar
TCVN 1651-1 16 Bar
TCVN 1651-1 18 Bar
TCVN 1651-1 20 Bar
TCVN 1651-1 22 Bar
TCVN 1651-1 25 Bar
TCVN 1651-1 28 Bar
TCVN 1651-1 32 Bar
TCVN 1651-1 36 Bar
TCVN 1651-1 40 Bar
ISO 6935-1 6 Coil/Bar
ISO 6935-1 8 Coil/Bar
ISO 6935-1 10 Coil/Bar
ISO 6935-1 12 Coil/Bar
ISO 6935-1 14 Coil/Bar
ISO 6935-1 16 Coil/Bar
ISO 6935-1 20 Coil/Bar
ISO 6935-1 22 Coil/Bar
BS 4482 2.5
BS 4482 5
BS 4482 6
BS 4482 7
BS 4482 8
BS 4482 9
BS 4482 10
BS 4482 12